Third Generation F-Body Message Boards

 
Page 1 of 10
1
2
3
4
5
Last »
Search: Posts Made By: paulo57509
Showing results 1 to 50 of 499
Search took 0.14 seconds.
Forum: Car Audio
10-19-2023, 01:13 PM
Replies: 12
Views: 859
Posted By paulo57509

Re: Speakers: What size and where? Best bang 4 your buck, AND effort.

Yes, just plain 4x6 up front. They were designed to be fit under the dash pad; supplied with no grills. Pioneer did supply plastic spacers with them that were needed for clearance because the...
Forum: Car Audio
10-18-2023, 07:30 PM
Replies: 12
Views: 859
Posted By paulo57509

Re: Speakers: What size and where? Best bang 4 your buck, AND effort.

This was decades ago; I used Pioneer coaxial 4x6's in the dash and 6x9's in the sail panels. I went with the stock size and locations to avoid any panel or bracket cutting. I can't recall what model...
Forum: Interior
10-18-2023, 07:01 PM
Replies: 11
Views: 631
Posted By paulo57509

Re: Interior dimensions question

I brought home a Home Depot, cheap a$$ Bushwood (or whatever brand), 72" high cabinet kit in the 3rd gen. I had to lash down the hatch. IIRC, there was a couple of feet sticking out the back with...
Forum: Body
10-17-2023, 07:02 PM
Replies: 8
Views: 678
Posted By paulo57509

Re: (Firebird) Hood stuck shut in a weird way...

Looks like the hood latch was in the closed position and the hood was slammed shut. Now the safety latch is holding the hood closed. There's no room to push the hood down to release the safety...
Forum: Electronics
10-04-2023, 02:00 PM
Replies: 4
Views: 330
Posted By paulo57509

Re: Car clicks and looses all power right before I go to start the car (ignition )

FWIW, it's most likely the Main Relay that's giving you problems. Classic issues with Honda and Acura.

...
Forum: Carburetors
10-04-2023, 01:56 PM
Replies: 3
Views: 348
Posted By paulo57509

Re: Newbie with LG4 automatic and SES light

Is your OBD connector look like this?

https://cimg5.ibsrv.net/gimg/www.thirdgen.org-vbulletin/474x275/th_1995057092_c7d09f01577db8dcc0a1529b9ad3b7329cf896ca.jpg

You need to jump terminals A&B.
Forum: Tech / General Engine
09-26-2023, 03:25 PM
Replies: 16
Views: 1,415
Posted By paulo57509

Re: Replacing hard fuel line with rubber section/fuel filter housing size

There was a time when you could lookup every part a particular carburetor used just by providing the carburetor number. Does such a thing (used to be a parts book) exist anymore?
Forum: Transmissions and Drivetrain
09-22-2023, 09:22 AM
Replies: 9
Views: 565
Posted By paulo57509

Re: How do you judge a quality roller bearing?

How do I judge bearing quality? This is one way.

I searched for more than a few years for hubs that were NLA. I finally found hubs that came with bearings. These were promptly thrown into the...
Forum: Body
09-22-2023, 09:06 AM
Replies: 2
Views: 241
Posted By paulo57509

Re: Rear hatch struts

There's different supports depending on how the hatch is configured (read: weight).
...
Forum: TPI
09-18-2023, 05:38 PM
Replies: 13
Views: 921
Posted By paulo57509

Re: TPI runner removal advice needed

This bolt?


https://cimg8.ibsrv.net/gimg/www.thirdgen.org-vbulletin/474x316/untitled_42_93d350e0c7dba3467e7df1ed4c7c04dcee07b96e.jpg
It's been a long while (:huh:).....these bolts are SHCS, yes?...
Forum: Tech / General Engine
09-14-2023, 06:43 PM
Replies: 25
Views: 1,501
Posted By paulo57509

Re: Californians, What are the options?

The only time I had the inspection tech look for CARB EO numbers was after a recent fail; they crawled underneath to check that the cat had the required CARB EO stamps. This was with a '92 Lumina.
Forum: Transmissions and Drivetrain
09-01-2023, 11:24 PM
Replies: 1
Views: 255
Posted By paulo57509

Re: Decode the date of this axle possible ?

I think you need the numbers that are stamped on one of the axle tubes. However, the only production info is the day it was assembled. This is from the '87 FSM for Saginaw built rear axles. No...
Forum: Tech / General Engine
09-01-2023, 10:52 PM
Replies: 9
Views: 501
Posted By paulo57509

Re: How does this unusual hose clamp work?

If you absolutely have to reuse this type of clamp, open them up before removing the hose; loosen the screw, take a wide, bladed screwdriver, place it where the arrows are and smack the handle with...
Forum: Exhaust
09-01-2023, 10:00 PM
Replies: 7
Views: 652
Posted By paulo57509

Re: Any other headers fit the SLP y-pipe?

Are SLP headers for 3rd gens rare animals? If so, I'd be inclined to leave them as-is and cap the AIR tubes. IIRC, SLP uses 304SS for their headers.
...
Forum: Electronics
08-20-2023, 09:22 PM
Replies: 6
Views: 301
Posted By paulo57509

Re: Dash light dinner function?

Correct headlight switch operation:

Full CCW after click = full cluster brightness and courtesy lights on
Full CCW before click = full cluster brightness
Full CCW before click to CW = variable...
Forum: Transmissions and Drivetrain
08-05-2023, 05:28 PM
Replies: 7
Views: 777
Posted By paulo57509

Re: 700r4 pan with drain plug

If you're going to go with a universal drain plug kit, I prefer the Dorman 65128; it has a straight thread plug that I use with a seal washer (stat-o-seal or aluminum). I think it seals better than...
Forum: Cooling
08-02-2023, 07:43 PM
Replies: 3
Views: 427
Posted By paulo57509

Re: Cooling Fan Doesn’t Turn on with AC (1987 L98 w/Dual Fans)

See attached. Sorry the schematic isn't in color.
Forum: Tech / General Engine
07-28-2023, 03:43 PM
Replies: 32
Views: 1,721
Posted By paulo57509

Re: Bent pushrod

Jumped timing chain = bent and broken push rods. No bent valves.


https://cimg0.ibsrv.net/gimg/www.thirdgen.org-vbulletin/1480x2000/pushro_1_2__1889b3dfb80796e3deb6054da70a4611c735d946.jpg
1968...
Forum: Electronics
07-16-2023, 07:37 PM
Replies: 3
Views: 362
Posted By paulo57509

Re: Key has a hard time starting the car

More definition needed regarding, "it sounds like it's having a hard time turning it over". What sound is it making?
Forum: Cooling
07-05-2023, 05:56 PM
Replies: 3
Views: 577
Posted By paulo57509

Re: Best AC compressor recommendations please

If the refrigerant leaked out, chances are there's air in the system that needs to be removed before refrigerant is put in. Are you sure there's nothing in the system?

First step is to sniff out...
Forum: Suspension and Chassis
07-04-2023, 09:41 PM
Replies: 8
Views: 1,078
Posted By paulo57509

Re: Strut to spindle bolt size?

If you're going to be buying a lot of fasteners, you're going to need a way to ID them, like caliper and thread gauges. There are a lot of options.

They are M16 of fine (unknown) threads/mm and...
Forum: Interior
07-04-2023, 04:32 PM
Replies: 4
Views: 493
Posted By paulo57509

Re: Spare Tire Tools Proper Storage

Forgot to mention that there's a plastic spacer that fits in the bottom of the well under the spare tire.

Search for P/N 14090308 to find images.
Forum: Tech / General Engine
07-04-2023, 04:23 PM
Replies: 1
Views: 444
Posted By paulo57509

Re: Please Help! O k, check this out my number 3. Intake Valve broke in half across

Reversion. Just follow the intake runner from #3. It probably ends up at #8.

I've seen a valve seat break apart on a 330ci FE Ford. I found pieces of the seat in four other cylinders.
Forum: Interior
07-02-2023, 08:13 PM
Replies: 4
Views: 493
Posted By paulo57509

Re: Spare Tire Tools Proper Storage

Hopefully this helps a bit. From the 1987 owner's manual. This one is for the scissor jack. Sorry the reference photo doesn't show much. If you have an aluminum space saver there's a plastic...
Forum: Electronics
06-29-2023, 10:29 PM
Replies: 4
Views: 547
Posted By paulo57509

Re: Weird switch inside motor

It's a switch with only one wire. It's not really functional in its current state.

It's a decoy switch. :rolleyes:
Forum: Tech / General Engine
06-27-2023, 07:22 PM
Replies: 7
Views: 927
Posted By paulo57509

Re: Removing steering plate

I inherited an OTC 7815. The arbor that screws on the steering shaft is tapered. Makes putting the wire retaining ring back in place like installing valve stem seals. Makes it easier for us guys...
Forum: Cooling
06-23-2023, 01:19 PM
Replies: 2
Views: 623
Posted By paulo57509

Re: 1987 Camaro Iroc Z 5.o TPI cooling issue

This won't help when the car is stationary, but is the air deflector under the radiator support present?
Forum: Electronics
06-20-2023, 05:42 PM
Replies: 11
Views: 1,495
Posted By paulo57509

Re: What does this wire go to?

The temperature diagnostic switch is essentially a temperature sensor. The sensor wire is routed along the passenger side fuel rail (IIRC). It looks like this:...
Forum: Cooling
06-20-2023, 05:26 PM
Replies: 6
Views: 485
Posted By paulo57509

Re: Part number or name for this heater core like

Roll some (hose) beads in the tube and you'll have a real trick replacement.
Forum: Electronics
06-19-2023, 06:40 PM
Replies: 11
Views: 1,495
Posted By paulo57509

Re: What does this wire go to?

EGR Temperature Diagnostic Switch
Forum: Cooling
06-19-2023, 06:22 PM
Replies: 6
Views: 485
Posted By paulo57509

Re: Part number or name for this heater core like

If you have a part number:

https://www.rearcounter.com/

https://www.partsvoice.com/

Good luck
Forum: Transmissions and Drivetrain
05-18-2023, 07:47 PM
Replies: 8
Views: 600
Posted By paulo57509

Re: Cannot remove diff cover

This used with a hammer works every time.

https://cimg3.ibsrv.net/gimg/www.thirdgen.org-vbulletin/2000x971/20211002_182745_k_d_aa034555a9336715c667134d472f55f9c1a71d70.jpg
Forum: Electronics
05-12-2023, 08:37 PM
Replies: 12
Views: 483
Posted By paulo57509

Re: starter wiring heat problem

Sometimes, the symptoms described can be worn solenoid contacts within.

Back in the day when I was cash poor, I would do this to get more mileage out of a GM solenoid with worn contacts (pardon...
Forum: Fabrication
05-06-2023, 03:18 PM
Replies: 32
Views: 1,007
Posted By paulo57509

Re: Rivet nuts

I have one of these:
...
Forum: Interior
05-03-2023, 02:54 PM
Replies: 1
Views: 344
Posted By paulo57509

Re: '88 IROC turn signal covers

If you can't find them you can make your own. IIRC, one side of the original discs is matte finished to diffuse the light. Perhaps some Testors Dull Cote would work?
...
Forum: Interior
04-19-2023, 11:28 PM
Replies: 12
Views: 528
Posted By paulo57509

Re: Dash Vent Detent Washers

I used o-rings as well. They've been in place since 1990.
Forum: Tech / General Engine
02-15-2022, 05:54 PM
Replies: 6
Views: 453
Posted By paulo57509

Re: can anyone identify these heads on a 350

I came across images of World Product heads that look like what's posted. Might be just a stock photo. I would pull a VC to confirm.
Forum: Body
04-02-2021, 06:51 PM
Replies: 18
Views: 21,005
Posted By paulo57509

Re: Front end jacking and Jack stand points?

There are a lot of work-arounds that work.

1) I have a short stack of 1x12 pine boards screwed together like a pyramid, 1.5" works form me at stock ride height.
...
Forum: Body
09-04-2020, 03:50 AM
Replies: 25
Views: 13,411
Posted By paulo57509

Re: Just put new weatherstripping in and door closes hard

Try comparing the "slam" when closing the door with the window closed vs. the window opened.

It wouldn't appear that this is necessary, but I've had cars where the window needed to be re-adjusted...
Forum: Interior
09-01-2020, 09:12 PM
Replies: 21
Views: 758
Posted By paulo57509

Re: What parts to repair 1987 pull down hatch?

I think Lonsal (a member here) may have used parts.

Dorman has new housing/motor parts (check their catalog/ebay). However, I think Dorman quality can be rather sketchy - I bought a new...
Forum: Transmissions and Drivetrain
08-30-2020, 09:31 PM
Replies: 2
Views: 237
Posted By paulo57509

Re: Firebird Shifting not Returning

Can you have a helper operate the shifter while you look under the car to see what's going at the trans?
Forum: Tech / General Engine
08-29-2020, 04:44 PM
Replies: 3
Views: 1,010
Posted By paulo57509

Re: Fuel filler neck grommet installation?

https://www.thirdgen.org/forums/tech-general-engine/658641-changing-gas-tank-filler.html#post5356234
Forum: Car Audio
08-27-2020, 03:08 PM
Replies: 11
Views: 2,586
Posted By paulo57509

Re: Power Antenna

Different plastics, but I've used Lubriplate 105 in the plastic hatch pulldown with no ill effects. This was ~30 years ago.

Last time I opened it up, I used Lubriplate SFL-0 synthetic, food grade...
Forum: Carburetors
08-24-2020, 05:17 PM
Replies: 3
Views: 440
Posted By paulo57509

Re: Hard Starting - No Fuel Prime (LG4, non-CC)

The well plugs under the bowl are notorious for leaking.

Perform a search in this section and you'll find posts on how to diag and repair.
Forum: Cooling
08-21-2020, 03:35 PM
Replies: 4
Views: 273
Posted By paulo57509

Re: Testing a Used Compressor

How was this used compressor stored? Was it open to the atmosphere or was the ports plugged? Was the oil left in it or was it drained?

Personally, I would avoid using any used A/C components. ...
Forum: Cooling
08-21-2020, 03:24 PM
Replies: 4
Views: 298
Posted By paulo57509

Re: Air Cleaner Housing Removal

::deleted::
Forum: Electronics
08-11-2020, 04:17 AM
Replies: 11
Views: 355
Posted By paulo57509

Re: Turn Signal Wiring

Stupid question: Did you replace the correct flasher? There are two; one for the turn signals, one for the hazards.
Forum: Body
08-11-2020, 04:03 AM
Replies: 15
Views: 12,168
Posted By paulo57509

Re: Door vapor barrier glue - what is close to factory?

FWIW, I still have both left and right door vapor barriers that I special ordered from the dealership. They've been rolled up in a cabinet for +30 years. I can't even recall why I bought them. The...
Forum: Transmissions and Drivetrain
06-11-2020, 07:14 PM
Replies: 14
Views: 585
Posted By paulo57509

Re: Flexplate knock or spark knock due to timing way off

Sorry. The dementia is setting in these days.
Forum: Carburetors
06-11-2020, 07:07 PM
Replies: 4
Views: 3,005
Posted By paulo57509

Re: No compression in cylinder 8

Where's the leakage? Grease Monkey Method:

Take your oiler (https://i.postimg.cc/15gzcgzy/s-l1002.jpg (https://postimages.org/)) and squirt some engine oil (~tablespoon) in the cylinder through...
Showing results 1 to 50 of 499
 
Page 1 of 10
1
2
3
4
5
Last »


 
Forum Jump


All times are GMT -5. The time now is 09:43 PM.