Third Generation F-Body Message Boards

 
Page 1 of 10
1
2
3
4
5
Last »
Search: Posts Made By: MoJoe
Showing results 1 to 50 of 500
Search took 0.09 seconds.
Forum: LTX and LSX
09-09-2022, 07:13 AM
Replies: 68
Views: 50,228
Posted By MoJoe

Re: Connector ID, PN and interchanges

Yeah, there was some "oops" to the original design and the pre-MetriPack connectors. Engine heat, electrical heat, and age shrinks the insulation covering the wires to the Fuel Pump Relay, exposing...
Forum: Members Camaros
10-06-2021, 05:17 PM
Replies: 31
Views: 75,095
Posted By MoJoe

Re: Third time's a charm - 87 IROC

@DynoDave - Thanks.

The AIR tube is the factory piece to supply the driver's side. I just couldn't replicate the (tight)bends and brackets. Since I moved the diverter valve, I made/used simple...
Forum: Members Camaros
10-06-2021, 01:58 PM
Replies: 31
Views: 75,095
Posted By MoJoe

Re: Third time's a charm - 87 IROC

I'm back. When my wife goes to visit her mom, I get car time. During her trip earlier this year;

I pulled the engine,
swapped cams ... I decided LT4 HOT was too much for LTRs, swapped to GM...
Forum: Engine/Drivetrain/Suspension Wanted
10-06-2021, 01:38 PM
Replies: 3
Views: 258
Posted By MoJoe

Re: Wanted- Lt4 Hotcam

I have one I can ship from Denver.

Does $125 Paypal Friends-and-Family work for you?
...
Forum: LTX and LSX
09-08-2021, 07:50 AM
Replies: 1,905
Views: 333,821
Posted By MoJoe

Re: What ever happened to QwkTrip's car anyway?

For 16", if you step up to 255/50-16, there are 3 brands available (at DiscountTire)
BFG G-Force Sport Comp 2
Mickey Thompson - ET Street S/S
Toyo - Proces R888R
Forum: Organized Drag Racing and Autocross
05-27-2021, 07:43 AM
Replies: 397
Views: 25,150
Posted By MoJoe

Re: headers $2000 GOING Big Block!

The frame side mounts look like they have an offset, and both are in the "make the engine lower" position. This also makes the through bolts closer to each other.
What happens if you flip one or...
Forum: LTX and LSX
04-04-2021, 08:33 AM
Replies: 1,905
Views: 333,821
Posted By MoJoe

Re: What ever happened to QwkTrip's car anyway?

The springs are trying to rotate the nose of the axle up. If the car is sitting on the tires, then the weight is increasing that upwards force at the tip of the torque arm.

To remove the torque...
Forum: Engine/Drivetrain/Suspension Parts for Sale
02-21-2021, 06:03 PM
Replies: 1
Views: 541
Posted By MoJoe

SOLD! TPIS twin 58mm Throttle Body $400, new, shipped

SOLD!

I have a TPIS 58mm throttle body that needs a new home. It is in new condition, includes billet IAC housing, TPiS plate, gasket, and screws for TPS sensor.

The throttle arm accommodates...
Forum: LTX and LSX
12-08-2020, 10:46 AM
Replies: 1,905
Views: 333,821
Posted By MoJoe

Re: What ever happened to QwkTrip's car anyway?

I watched the video... 2.5 times! And have some questions about the specifics.

On the frame side bracket:

1. Stepped bolt -> M12 -> drill out holes for 9/16 bolts. Do you have the bolt length...
Forum: Transmissions and Drivetrain
10-27-2020, 03:36 PM
Replies: 8
Views: 8,009
Posted By MoJoe

Re: U-JOINT HELP, PLEASE

Thanks Midias. That chart looks familiar, and should help the next person wondering. :thumbsup:
Forum: Transmissions and Drivetrain
10-27-2020, 08:47 AM
Replies: 8
Views: 8,009
Posted By MoJoe

Re: U-JOINT HELP, PLEASE

Sorry to bring this thread back from its 13 year nap... During my swap to install a Dana 44 in place of the factory 10-bolt, I couldn't figure out why the u-bolts wouldn't fit over the u-joint...
Forum: Aftermarket Product Review
10-26-2020, 05:22 PM
Replies: 3
Views: 1,483
Posted By MoJoe

Re: L31 TPI Build

Welcome rpl!

L31/TPI - vortec heads are good. Vortec TPI base is reported to flow poorly. You will have to add an external exhaust-to-EGR supply, which is not available with stock manifolds, but...
Forum: Transmissions and Drivetrain
07-01-2020, 04:56 PM
Replies: 2
Views: 454
Posted By MoJoe

Re: Labor price to install ring & pinion?

GD - thanks for the information.
Forum: Transmissions and Drivetrain
07-01-2020, 11:22 AM
Replies: 2
Views: 454
Posted By MoJoe

Labor price to install ring & pinion?

I got a quote of $500 labor to install a R&P? Is that a fair charge for labor? Parts are extra.

Details: Dana 44, not in-car, 4.11 to 3.92 so I can re-use the carrier. The rest of the quote...
Forum: Transmissions and Drivetrain
06-22-2020, 08:21 AM
Replies: 71
Views: 79,114
Posted By MoJoe

Re: Automatic to T56 swap MADE EASY Tutorial *Pics*

Here are some typical wire coding off the top of my head:
Red - battery voltage, always hot.
Pink - hot in run+start
Orange - hot in accessory+run

To activate the solenoid, one side needs to...
Forum: TPI
12-23-2019, 08:09 AM
Replies: 124
Views: 18,851
Posted By MoJoe

Re: TPI Combo - Low Dyno Results

Dan, the transmission guy, thought the trans case is/was warped, and not usable?
Forum: Fabrication
12-04-2019, 08:06 PM
Replies: 12
Views: 4,446
Posted By MoJoe

Re: LS valve covers on SBC?

Thanks, Shifty. While disappointing (adapter not likely), this is the kind of answer I was hoping would come out.
Forum: Fabrication
12-02-2019, 07:11 AM
Replies: 12
Views: 4,446
Posted By MoJoe

Re: LS valve covers on SBC?

Thanks Drew. Have you found an adapter to put LS valve covers on SBC center bolt heads?
Forum: Fabrication
12-01-2019, 09:28 AM
Replies: 12
Views: 4,446
Posted By MoJoe

Re: LS valve covers on SBC?

Those cast aluminum covers are GM #12480127. I found them at Summit Racing, for a lot more than I remember! Or similar is GM Performance slant-edge #141-925. Neither I've seen as polish or chromed....
Forum: Fabrication
12-01-2019, 08:54 AM
Replies: 12
Views: 4,446
Posted By MoJoe

Re: LS valve covers on SBC?

Not engraved, but more of a cast-in lettering. The LS and/or SBC perimeter-bolt covers have a substantial logo, while the SBC center bolt covers tend to get a dinky after-thought of a logo. And even...
Forum: Fabrication
11-29-2019, 04:55 PM
Replies: 12
Views: 4,446
Posted By MoJoe

LS valve covers on SBC?

Everyone and their brother offers an adapter to put old school valve covers on an LS.
But, does anyone offer an adapter to go the other way...? LS valve covers on an SBC?... preferably center bolt...
Forum: Members Camaros
08-18-2019, 10:34 AM
Replies: 901
Views: 101,270
Posted By MoJoe

Re: Long time coming AKA My 91 Z28 Vert build thread

Thanks for the link. Fabrication can be fun. But, sometimes it is worth the time to purchase pre-made. :)
Forum: Members Camaros
08-18-2019, 08:07 AM
Replies: 901
Views: 101,270
Posted By MoJoe

Re: Long time coming AKA My 91 Z28 Vert build thread

Whose bracket did you buy? Are you happy with it (fit, finish)? Or do recommend a different one?
Forum: Body
07-29-2019, 11:43 AM
Replies: 25
Views: 9,953
Posted By MoJoe

Re: How to remove lower ground fx skirt?

It is a 7mm hex head on a basic sheet metal screw. Since it is just a sheet metal screw, any close replacement should work. I'd guess 3/4" length, maybe a #6 (3/32?) diameter. Take your last one...
Forum: Interior Parts for Sale
07-08-2019, 09:20 PM
Replies: 486
Views: 62,515
Posted By MoJoe

Re: power window relay kit EASY to install!

:imo:If you read the thread, you will have noticed John pops in for a couple days, then is gone for a couple months. Despite seemingly half of the 437 posts have been comments like yours; it's been X...
Forum: LTX and LSX
03-11-2019, 07:02 AM
Replies: 129
Views: 47,212
Posted By MoJoe

Re: HAWKS 408ci LSX Twin Turbo Convertible Formula Build w/ Pics

Not sure on the wheel width, but the tires are 335, so the wheel is likely 12.5", perhaps wider.
No, those are not the stock wheel tubs. Typically 285-295 is the widest tire in the factory tub. ...
Forum: LTX and LSX
02-18-2019, 07:22 AM
Replies: 1,905
Views: 333,821
Posted By MoJoe

Re: What ever happened to QwkTrip's car anyway?

To add one more option to the mix, you can use an LS master cylinder as well. The overall MC length is shorter than 3rd gens, and the port spacing is closer as well. It has metric threads. You can...
Forum: Cooling
10-11-2018, 07:57 AM
Replies: 8
Views: 13,237
Posted By MoJoe

Re: 98 vortec questions

That is a good point: Even if the pump and block have the bypass, because the stock Vortec head does not have the passage, you have to run the external bypass.

One of my preferred tips is to drill...
Forum: Members Camaros
08-31-2018, 07:23 AM
Replies: 901
Views: 101,270
Posted By MoJoe

Re: Long time coming AKA My 91 Z28 Vert build thread

Congratulations! Your hard work and attention to detail has been very impressive, even for those of us just lurking while following your (re)build.
Your car looks great. I am looking forward to...
Forum: Members Camaros
07-29-2018, 08:09 AM
Replies: 457
Views: 94,435
Posted By MoJoe

Re: Detroit Speed 1987 Camaro Test Car 2.0

Swapping the LS plastic tank is a popular swap. It has the charcoal can at / with / on the tank, to move it from under the hood, to at the tank.
Forum: Members Camaros
07-28-2018, 07:16 AM
Replies: 457
Views: 94,435
Posted By MoJoe

Re: Detroit Speed 1987 Camaro Test Car 2.0

Your description is backwards; the charcoal can catches vapors from the tank, and when running, the engine will draw off and burn those vapors. It will help your car stink less when you park it in...
Forum: Transmissions and Drivetrain
07-15-2018, 07:07 PM
Replies: 1
Views: 368
Posted By MoJoe

Dana 44 and LS1 (rear) brakes

I have a Dana 44, and want to swap out the iron (told to be) 1LE brakes, for LS1 brakes. I've swapped LS1 brakes onto the 10-bolt with no problem. All the information I've seen suggests putting the...
Forum: Alternative Port EFI Intakes
04-07-2018, 02:18 PM
Replies: 16
Views: 2,115
Posted By MoJoe

Re: Hawks custom mini ram

That's quite a Frankenstein. Looks like a tunnel ram intake with a lid welded on the plenum to make it forward facing. JB welding the injectors bungs instead of welding. Is there really not an...
Forum: History / Originality
03-04-2018, 03:32 PM
Replies: 299
Views: 37,244
Posted By MoJoe

Re: '82 CFI Pace Car Resto

Adding weight to the crank is expensive. Drilling into a counter weight to remove weight should be pretty cheap.

It also depends on how close the new pistons weigh vs factory. I don't know how...
Forum: Transmissions and Drivetrain
02-07-2018, 09:32 PM
Replies: 25
Views: 2,469
Posted By MoJoe

Re: Ordered Strange S60

Brand new parts sure are purdy! :nod:
Forum: Fabrication
12-31-2017, 08:21 AM
Replies: 16
Views: 6,149
Posted By MoJoe

Re: Custom serpentine belt tensioner

Grover, You have almost no belt wrap on the water pump. I'm surprised you don't get slippage and have overheating problems.
Forum: Tech / General Engine
11-18-2017, 05:08 PM
Replies: 14
Views: 2,167
Posted By MoJoe

Re: SP 383 GM

GM does have a crate 427! $10,500 at Summit (https://www.summitracing.com/parts/nal-19331572/overview/make/chevrolet)
Forum: LTX and LSX
10-02-2017, 07:09 AM
Replies: 1,905
Views: 333,821
Posted By MoJoe

Re: What ever happened to QwkTrip's car anyway?

And for someone who didn't already know the name Tony Mamo, I was surprised when DuckDuckGo returned several responses.
Forum: Members Camaros
09-20-2017, 07:22 AM
Replies: 115
Views: 10,194
Posted By MoJoe

Re: Steve's IROC Z

Depending on your resources, getting the body up and over the drivetrain can be very difficult. Compare that to; if you have an engine hoist, you can always remove the engine the conventional way.
...
Forum: Organized Drag Racing and Autocross
09-12-2017, 09:11 PM
Replies: 8
Views: 1,174
Posted By MoJoe

Re: Will I run 12s

Camel hump heads - great in 1970. Much better designs are available.
Vortec - great bang for the buck. $600-ish new, or the better bargain shoppers can find used in the $100 range.
AFR, etc - If...
Forum: Interior Parts for Sale
08-15-2017, 07:12 AM
Replies: 486
Views: 62,515
Posted By MoJoe

Re: power window relay kit EASY to install!

Mine arrive last night.
Forum: LTX and LSX
08-12-2017, 07:55 AM
Replies: 54
Views: 3,330
Posted By MoJoe

Re: Spending money too fast....LS swap

LS input shaft is longer than the LT.


The Cavalier slave is larger than the T5/T56 slave. As the slave/driven cylinder, being larger reduces the travel. (Less output for the given input). This...
Forum: LTX and LSX
08-12-2017, 07:44 AM
Replies: 54
Views: 3,330
Posted By MoJoe

Re: Spending money too fast....LS swap

I think you have the idea correct, and excuse me if I get too nit-picky, but your description is lacking:
Every(?) manual transmission has a ThrowOut Bearing (TOB) to push on the pressure plate to...
Forum: LTX and LSX
08-05-2017, 07:56 AM
Replies: 54
Views: 3,330
Posted By MoJoe

Re: Spending money too fast....LS swap

T56s are in demand. I got a local LT T56 for $1700, add the mechanical speedo conversion for $325. I haven't driven it, yet, so I don't know its condition.

For the kind of prices for used, buying...
Forum: Suspension and Chassis
08-05-2017, 07:41 AM
Replies: 4
Views: 3,623
Posted By MoJoe

Re: Panhard Bar Relocation Kits- Which One To Buy

The 2064 kit is adjustable (1 3/4"-4"), while the 2063 kit is not (2 1/4"). If you need adjustability, then the choice is clear. If not, the 2063 is a simpler install.

You already have the...
Forum: Electronics
08-05-2017, 07:29 AM
Replies: 7
Views: 482
Posted By MoJoe

Re: Reverse lights on in every gear

The ground for the reverse lights is at the lights. The on/off switch at the shifter connects power from the fuse box to the wire running to the lights. It is a blue and light green wire. These...
Forum: Interior Parts for Sale
08-04-2017, 07:13 AM
Replies: 486
Views: 62,515
Posted By MoJoe

Re: power window relay kit EASY to install!

It sounds like business is good. While I'm not in a hurry at the moment (basement construction), I don't want to forget about it, nor be forgotten! :)
Forum: Transmissions and Drivetrain
07-15-2017, 09:26 PM
Replies: 7
Views: 791
Posted By MoJoe

Re: Auto to T56. Lt or Ls? Wiring help

Would have helped if I noticed you are going LS3, and actually read your whole post... :doh:

1) Yes, getting an LS T56 would be easiest, and probably cheapest in the long run. Piecing a swap...
Forum: Transmissions and Drivetrain
07-15-2017, 08:34 AM
Replies: 7
Views: 791
Posted By MoJoe

Re: Auto to T56. Lt or Ls? Wiring help

1) The LT T56 is a bolt on, but you are limited to the pull style clutch. It worked for the factory, even with upgrades. Unless you are going to 400+ HP, you are likely covered. I think converting...
Forum: History / Originality
07-13-2017, 05:49 PM
Replies: 33
Views: 2,874
Posted By MoJoe

Re: New N10 on eBay???

Pricy for sure. I though an aftermarket company (MagnaFlow) built a dual cat SS exhaust that has since been discontinued. Mandrel bends means not factory. But could be SLP.
Showing results 1 to 50 of 500
 
Page 1 of 10
1
2
3
4
5
Last »


 
Forum Jump


All times are GMT -5. The time now is 01:22 PM.