Third Generation F-Body Message Boards

 
Page 1 of 10
1
2
3
4
5
Last »
Search: Posts Made By: NoEmissions84TA
Showing results 1 to 50 of 489
Search took 0.02 seconds.
Forum: Transmissions and Drivetrain
05-10-2024, 07:34 PM
Replies: 16
Views: 436
Posted By NoEmissions84TA

Re: Urgent question

:huh:
:eek: :doh: :eek: :doh: :eek:

:idiot:
Forum: Tech / General Engine
05-10-2024, 05:34 PM
Replies: 19
Views: 575
Posted By NoEmissions84TA

Re: PCV Valve Delete and RMS Oil Leak - Thoughts?

Few know this and even fewer actually know to use sealer here:

https://cimg2.ibsrv.net/gimg/www.thirdgen.org-vbulletin/546x971/rear_main_cap_37dc159d8b51dbb64882f169c6badbd09fb33757.jpg

It's a...
Forum: Tech / General Engine
04-27-2024, 10:02 PM
Replies: 2
Views: 181
Posted By NoEmissions84TA

Re: Short Rough Idle After Start Up

Sounds like lack of fuel or a large vacuum leak.
Check your TBI base gasket.
Also manually work the EGR valve. It could be stuck open.
Forum: Tech / General Engine
04-15-2024, 06:18 PM
Replies: 21
Views: 468
Posted By NoEmissions84TA

Re: Wierd ticking problem

Step #1 - find the source of your tick. Use a length of vacuum / windshield washer size tubing to locate.
Put one end in your ear and use the other end to probe around. You are just guessing until...
Forum: Engine Swap
04-15-2024, 06:05 PM
Replies: 4
Views: 167
Posted By NoEmissions84TA

Re: SBC L31 to 700R4

The converter is not supposed to be bottomed out in the pump.
1/8" clearance is ideal. Use flat washers between to achieve that clearance.
Your flexplate IS installed correctly.
Forum: Tech / General Engine
04-15-2024, 04:56 PM
Replies: 5
Views: 264
Posted By NoEmissions84TA

Re: PCV Routing Question (305 SBC)

Did you also swap to a vacuum advance distributor?

And if that intake manifold is an Edelbrock Torker II single plane, then this is completely wrong if your engine is stock or nearly so.
Forum: Electronics
04-07-2024, 08:16 PM
Replies: 7
Views: 238
Posted By NoEmissions84TA

Re: rattler 300 removal.

RATTLER 300 INSTALLATION MANUAL Pdf Download | ManualsLib (https://www.manualslib.com/manual/928841/Rattler-300.html)
Forum: Electronics
04-06-2024, 08:24 PM
Replies: 7
Views: 238
Posted By NoEmissions84TA

Re: rattler 300 removal.

Anything installed after the car left the dealer can be removed.
The difficulty will depend on how much of a hack job was done during the installation.
Not familiar with Rattler 300, but most...
Forum: Carburetors
03-28-2024, 04:19 PM
Replies: 4
Views: 279
Posted By NoEmissions84TA

Re: Seeking carb help: E4ME out of a 1984 camaro

https://cimg5.ibsrv.net/gimg/www.thirdgen.org-vbulletin/800x600/1711660632_886d2fac4c19d331911819a6f63029284d462cbf.jpeg

Cliffs High Performance Quadrajets – Quadrajet Rebuild Kits, Cabruretor...
Forum: DFI and ECM
03-28-2024, 11:13 AM
Replies: 0
Views: 175
Posted By NoEmissions84TA

How to unbrick your Holley ECU

I found this while surfing:

https://www.youtube.com/watch?v=h5nCI8xYCoA
Forum: Tech / General Engine
03-04-2024, 09:45 PM
Replies: 544
Views: 38,278
Posted By NoEmissions84TA

Re: Some questions during install of my new 406 SBC - street/strip/show/autoX

I am no expert on this, but I would think that you need a breather somewhere to let "filtered" air in.
Otherwise the vacuum pump could create enough negative pressure to suck in some of the gaskets.
Forum: Engine/Drivetrain/Suspension Wanted
03-04-2024, 09:20 PM
Replies: 5
Views: 168
Posted By NoEmissions84TA

Re: WTB OE for '86, 305 4V, Carb, intake, egr,, ex manifllds, engine harness etc.

I have the LG4 exhaust manifolds.
I have a good rebuildable E4ME carb also.
It's from an 87 Monte Carlo SS 17087129
And the quadrajet intake, sandblasted and clean.
It's time to clean some of...
Forum: Tech / General Engine
03-04-2024, 08:18 PM
Replies: 544
Views: 38,278
Posted By NoEmissions84TA

Re: Some questions during install of my new 406 SBC - street/strip/show/autoX

He wants to properly vent the crankcase without sucking out all of the oil.
Larger diameter = less velocity.
Forum: Engine Swap
03-04-2024, 08:13 PM
Replies: 18
Views: 510
Posted By NoEmissions84TA

Re: 1986 TA originally a 305 LG4, what's a good Smogable, 350 EASY swap?

So 25 years and done with smog - the same here in Connecticut. :thumbsup:
Forum: Tech / General Engine
01-29-2024, 08:11 PM
Replies: 19
Views: 575
Posted By NoEmissions84TA

Re: PCV Valve Delete and RMS Oil Leak - Thoughts?

2 piece RMS? Are the seal lips facing the engine?
Did you offset the parting lines?
If YES to all, then remove and clean the rearmost oil pan bolts and apply a sealer to them.
Please report...
Forum: Auto Detailing and Appearance
01-29-2024, 07:48 PM
Replies: 29
Views: 4,264
Posted By NoEmissions84TA

Re: I am truly disgusted by the TEMU ad banners

No SkinnyZ. Do use the adblockers. You can set an exception for sites like your Weather Network.
Forum: Tech / General Engine
01-19-2024, 09:16 PM
Replies: 14
Views: 375
Posted By NoEmissions84TA

Re: 357: My Assembly of Parts

It's nice to see that someone did the machining correctly:
.008” deck, 4.100" x .032" head gasket, 4.040” bore.
Forum: Classified Ads Feedback Board
01-16-2024, 10:57 PM
Replies: 8
Views: 947
Posted By NoEmissions84TA

Re: Scammed via classifieds "wayatlas@yahoo.com"

Since the subject has been brought up.....
I just got on FB to use Marketplace.
I googled a phone number for FB (they don't have any way of contacting a human) and dialed the number.
After a long...
Forum: Tech / General Engine
01-14-2024, 07:48 PM
Replies: 1
Views: 294
Posted By NoEmissions84TA

Re: Wrong Spark Plugs?

GM 3973370 SB Chevy Heads H-12-1969 1.94/1.50 Stock Camel Hump Over the Counter | eBay (https://www.ebay.com/itm/386312255020)

If this is what you've got, they are nothing special.
Also these...
Forum: Car Audio
01-14-2024, 07:33 PM
Replies: 12
Views: 1,037
Posted By NoEmissions84TA

Re: Old school baffle board install

Since your woofers will be facing opposite directions, are you changing the phase of the wiring to one of them so that both are throwing the air in the same direction, or do you want them opposing? ...
Forum: Interior
01-14-2024, 07:13 PM
Replies: 5
Views: 353
Posted By NoEmissions84TA

Re: Bonneville steering wheel in 1992 Firebird?

I like it. Any steering wheel with something like this grafted on in the center is FUGLY....
Forum: Body
12-20-2023, 11:02 AM
Replies: 18
Views: 849
Posted By NoEmissions84TA

Re: Crooked door?

The door hinges are welded, therefore non-adjustable.
I was told by the Pontiac dealer that the "fix" is to actually bend the door.
At least that's what they do for sagging doors.
Supposedly they...
Forum: Camaros for Sale
12-14-2023, 06:48 PM
Replies: 12
Views: 1,659
Posted By NoEmissions84TA

Re: Buy ASEDoc's IROC

Pictures please.
Forum: Members Firebirds
12-08-2023, 09:27 PM
Replies: 50
Views: 2,098
Posted By NoEmissions84TA

Re: 86 T/A KITT conversion

I hope you didn't have just plain water in the cooling system. :doh: Been there, done that.
One night of freezing temps is all it takes.
Forum: V6
10-22-2023, 05:49 PM
Replies: 3
Views: 336
Posted By NoEmissions84TA

Re: Fasteddi turbo build part 2

Awesome. :goodidea:
Forum: Engine Swap
10-16-2023, 07:16 PM
Replies: 18
Views: 1,069
Posted By NoEmissions84TA

Re: 400 SBC options

They were using spark plugs that were TOO SHORT.

And the 2 center exhaust valves are severely sunk.

Solve your problem by using better heads that have the accessory holes that you need.
Forum: Body
10-16-2023, 07:03 PM
Replies: 8
Views: 725
Posted By NoEmissions84TA

Re: (Firebird) Hood stuck shut in a weird way...

Take it for a slow ride taking hard left and right turns. It might pop open on its own.
Forum: Tech / General Engine
09-29-2023, 07:55 PM
Replies: 16
Views: 1,486
Posted By NoEmissions84TA

Re: Replacing hard fuel line with rubber section/fuel filter housing size

https://cimg2.ibsrv.net/gimg/www.thirdgen.org-vbulletin/202x200/38873_cb1355695794c6b33bd9815ac7d28ef854296e02.jpg

I got mine at NAPA. 3/8" barb to 3/8" inverted flare swivel. Edelmann 822660....
Forum: Carburetors
09-22-2023, 06:20 PM
Replies: 10
Views: 649
Posted By NoEmissions84TA

Re: What does this do and is it necessary?

It's the UFO valve. It sends out a signal to alert the aliens when you are driving on an isolated road out in the middle of nowhere at night.
Then they beam you up and give you an anal probe....
Forum: Interior Parts for Sale
09-17-2023, 09:20 PM
Replies: 1
Views: 555
Posted By NoEmissions84TA

Re: Almost NOS 1982 140 mph speedometer Z28

Watching this.
If you can get that price, then I will put up my TransAm version NIB with ZERO miles.
Forum: Theoretical and Street Racing
09-17-2023, 07:50 PM
Replies: 2
Views: 671
Posted By NoEmissions84TA

Re: dynamic compresion ratio

General rule - multiply by 10.
So your 7.2:1 DCR needs 72 octane.
Forum: Auto Detailing and Appearance
09-14-2023, 04:15 PM
Replies: 29
Views: 4,264
Posted By NoEmissions84TA

Re: I am truly disgusted by the TEMU ad banners

AdBlock Plus and AdGuard is what I am using.
You want the extension, not the program.
Forum: Firebirds for Sale
09-11-2023, 02:59 PM
Replies: 10
Views: 8,326
Posted By NoEmissions84TA

Re: 1984 15th anniversary Trans am for sale!

Look at the date of the post!
Forum: Electronics
09-10-2023, 06:43 PM
Replies: 36
Views: 1,003
Posted By NoEmissions84TA

Re: Finally doing the nuclear option

I better not have have jinxed myself with this praise for my old junk. I need it to work! Soon too.

:iagree: Welcome to my world.

The Progressive distributor sounds great "on paper", but I...
Forum: Electronics
09-10-2023, 06:00 PM
Replies: 36
Views: 1,003
Posted By NoEmissions84TA

Re: Finally doing the nuclear option

We are talking about an old-school 20+ year old MSD (non digital) box wired directly to the distributor's magnetic pickup coil via the green and purple wires from the MSD box.
Edit: it looks like...
Forum: Cooling
09-10-2023, 05:37 PM
Replies: 4
Views: 321
Posted By NoEmissions84TA

Re: Sanden compressor in place of somg pump with V-belt

OMG, that looks factory OEM. I love it.
Forum: Electronics
09-10-2023, 05:17 PM
Replies: 36
Views: 1,003
Posted By NoEmissions84TA

Re: Finally doing the nuclear option

skinny z - your distributor is set up the same as mine is - as in NO ICM at all.
The magnetic pickup triggers the MSD box directly. :thumbsup:
Forum: Engine Swap
09-09-2023, 10:43 PM
Replies: 14
Views: 887
Posted By NoEmissions84TA

Re: 305 multiport swap to 383 disaster

Throw that Thumpr cam in the trash.
Forum: Transmissions and Drivetrain
09-09-2023, 07:57 PM
Replies: 15
Views: 977
Posted By NoEmissions84TA

Re: Correct tool- T5 drain plug pictures

Ok then, use pipe thread sealant.
Forum: Transmissions and Drivetrain
09-09-2023, 05:24 PM
Replies: 15
Views: 977
Posted By NoEmissions84TA

Re: Correct tool- T5 drain plug pictures

This is what you have for your oil pan drain plug???

That is not the correct plug. You are showing a pipe plug with NPT (tapered) threads.

Your oil pan uses straight threads with a sealing...
Forum: Electronics
09-08-2023, 05:34 PM
Replies: 36
Views: 1,003
Posted By NoEmissions84TA

Re: Finally doing the nuclear option

What brand did you go with?
Forum: V6
09-08-2023, 03:53 PM
Replies: 3
Views: 336
Posted By NoEmissions84TA

Re: Fasteddi turbo build part 2

Nooooo! :huh:
Forum: Engine Swap
09-08-2023, 03:05 PM
Replies: 41
Views: 5,204
Posted By NoEmissions84TA

Re: 350 of a different color. 3.25" x 4.135"

Look at the date --- 2003 :doh: You're late by 2 decades.
Forum: Tech / General Engine
09-07-2023, 09:35 PM
Replies: 22
Views: 2,269
Posted By NoEmissions84TA

Re: Melling M55 Oil Pump: Suitability for High Performance

Images are from Grumpy's Performance Garage
skinny z - your new generic IS the stronger casting.
...
Forum: Body
09-03-2023, 09:07 PM
Replies: 5
Views: 578
Posted By NoEmissions84TA

Re: Paint Problem - Fish Eyes Galaore?

Good luck. I hope you don't have to start over.
Forum: Cooling
08-26-2023, 10:43 PM
Replies: 40
Views: 1,296
Posted By NoEmissions84TA

Re: overheating to 260*!!! Ive done everything!

Here is a couple that I found:
1955-1988 GM Cars Lower Radiator Coolant Hose Inner Support Spring 17" Long EA | eBay...
Forum: Cooling
08-26-2023, 06:02 PM
Replies: 40
Views: 1,296
Posted By NoEmissions84TA

Re: overheating to 260*!!! Ive done everything!

https://www.motortrend.com/uploads/f/167598725.jpg

The lower radiator hose should have a spring that keeps the hose from collapsing. The suction created by a properly working pump can flatten the...
Forum: European Region
08-26-2023, 05:47 PM
Replies: 5
Views: 392
Posted By NoEmissions84TA

Re: Hello from Holland!

Welcome.
Showing results 1 to 50 of 489
 
Page 1 of 10
1
2
3
4
5
Last »


 
Forum Jump


All times are GMT -5. The time now is 11:32 AM.