Third Generation F-Body Message Boards

 
Page 1 of 5
1
2
3
4
5
Search: Posts Made By: ratfink6923
Showing results 1 to 50 of 206
Search took 0.04 seconds.
Forum: Tech / General Engine
Today, 10:34 AM
Replies: 6
Views: 139
Posted By ratfink6923

Re: Loss of acceleration power after highway trip

Also, you may want to have someone press the accelerator while you watch the travel at the carb. Given your description of the shifting issue, you may have a stretched accel cable that isn't giving...
Forum: Tech / General Engine
Today, 10:33 AM
Replies: 6
Views: 139
Posted By ratfink6923

Re: Loss of acceleration power after highway trip

Once you find and correct your vacuum leak, put a vacuum gauge on it at idle and post your readings. Pay attention to any fluctuation at idle.
Vacuum gauge is a cheap, old school diag tool that...
Forum: Suspension and Chassis
05-13-2024, 10:28 PM
Replies: 3
Views: 95
Posted By ratfink6923

Re: Eibach pro kit did not lower front need help

That's definitely your issue, if they were stock v8 springs you'd be scraping low flying birds.

Rather than cut the eibachs, why not sell them whole and buy stock replacement V6 springs to cut?;...
Forum: Engine/Drivetrain/Suspension Parts for Sale
05-10-2024, 11:20 AM
Replies: 0
Views: 66
Posted By ratfink6923

(8) new in box Delco injectors for 6.0L LY6 $175

New in box GM fuel injectors for 2009-2010 6.0 33.9 lb/hr Part # 12587269
$175 shipped, obo. ...
Forum: Electronics
05-09-2024, 03:54 PM
Replies: 7
Views: 177
Posted By ratfink6923

Re: Firebird vs Camaro C100 Question

"F" car means the body line. That covers both models.
Forum: Engine/Drivetrain/Suspension Wanted
05-09-2024, 07:47 AM
Replies: 6
Views: 150
Posted By ratfink6923

Re: Tuned Port intermediate fuel feed pipes

I'm interested. No rush whatsoever
Forum: Engine/Drivetrain/Suspension Wanted
05-08-2024, 07:23 PM
Replies: 6
Views: 150
Posted By ratfink6923

Re: Tuned Port intermediate fuel feed pipes

I don't have a pic. 88-92 style.
Forum: Engine/Drivetrain/Suspension Wanted
05-08-2024, 05:38 PM
Replies: 6
Views: 150
Posted By ratfink6923

Tuned Port intermediate fuel feed pipes

Looking for the steel lines that run between the fuel rail and soft lines, mounted under the alternator. Twisted and broke mine removing the engine.
Forum: Interior Parts for Sale
05-08-2024, 09:00 AM
Replies: 4
Views: 177
Posted By ratfink6923

Re: Black interior plastics from 92 $100 for all

Unfortunately it didn't have a ttop bag.
The drivers side panel is prohibitively large, the pallet fee would be more than these are worth I believe. Where are you located?
Forum: Interior Parts for Sale
05-08-2024, 08:59 AM
Replies: 4
Views: 177
Posted By ratfink6923

Re: Black interior plastics from 92 $100 for all

I will try to get quotes by end of week. I still have your zip I believe.
Forum: Engine/Drivetrain/Suspension Parts for Sale
05-07-2024, 06:05 PM
Replies: 0
Views: 103
Posted By ratfink6923

Moog CC635 springs new in box $50obo

Found a set of Eibach springs after my return window closed. Prefer local pickup, shipping wont be worth it. ...
Forum: Engine/Drivetrain/Suspension Parts for Sale
05-07-2024, 06:01 PM
Replies: 1
Views: 110
Posted By ratfink6923

PCM with memcal1227165 (AKFM)

1227165 AKFM came out of my 88 305 auto
has not been tested. $275 shipped ...
Forum: Interior Parts for Sale
05-07-2024, 05:49 PM
Replies: 4
Views: 177
Posted By ratfink6923

Black interior plastics from 92 $100 for all

Removed from my donor car. Non carpeted. In fair to ok condition. Will not ship. Near Tampa, FL.
(2)Kick panels
(2) Sill plates. Drivers has crack but complete ...
Forum: Interior Parts for Sale
05-07-2024, 05:41 PM
Replies: 0
Views: 65
Posted By ratfink6923

Delco CD player out of 99 Camaro $85 plus shipping

Picked this up for my 88 but decided I wanted a backup camera. I replaced all of the knobs. Has not been tested, priced accordingly. ...
Forum: Engine/Drivetrain/Suspension Parts for Sale
05-07-2024, 05:34 PM
Replies: 0
Views: 145
Posted By ratfink6923

SOLD! SDPC Vortec Intake Manifold with TPIS EGR block off plates $450 obo

Purchased one for my build a few months ago. This one came up on marketplace near me with the fuel rails and runners I needed so I bought the package. Sandblasted and hot tanked. Comes with TPIS EGR...
Forum: TBI
05-04-2024, 07:19 PM
Replies: 3
Views: 126
Posted By ratfink6923

Re: CFI inlet manifold

The angles of the center intake mounting holes will be at a different angle. You can use a die grinder to wallow the intake out a little to get it to line up. Otherwise, should match up.
Forum: Cooling
04-23-2024, 10:29 AM
Replies: 35
Views: 590
Posted By ratfink6923

Re: A/c woes

Did you convert to r134? If you would, attach a picture of the high side fitting.
Forum: Cooling
04-21-2024, 04:20 PM
Replies: 8
Views: 210
Posted By ratfink6923

Re: Help 1986 Trans Am AC Pancake to rotary Compressor.

I would stick with the Delco style, but only if you're going to thoroughly flush and leak test the system. Make sure you change orifice tube sizes (I believe orange is the preferred for our climate)...
Forum: Suspension and Chassis
04-19-2024, 01:26 PM
Replies: 2
Views: 158
Posted By ratfink6923

Re: Iroc Struts

Any 40 year old strut is going to be toast. Most likely the springs are as well. Nearly any replacement you could find would be an improvement
Forum: Engine Swap
04-16-2024, 07:19 PM
Replies: 3
Views: 196
Posted By ratfink6923

Re: 305 to 350 swap for my Firebird

Transmission will be fine to keep. Make sure you go with an 87 or up 350, otherwise you'll need a different flex plate.

Otherwise, the swap is pretty straight forward
Forum: Electronics
04-15-2024, 09:48 PM
Replies: 8
Views: 228
Posted By ratfink6923

Re: 1992 Camaro RS needs interior wirning

There will be different connections for clutch pedal and backup lights. The backup lights may be engine harness side though, I'll have to check.
Forum: Electronics
04-15-2024, 09:32 PM
Replies: 8
Views: 228
Posted By ratfink6923

Re: 1992 Camaro RS needs interior wirning

Automatic car. 305 tbi. Power windows/locks/hatch release. Rear defrost. Cruise control. Intermittent wipers. Standard dome light. Base radio/rearview mirror (non lighted) vats car obviously. I'll...
Forum: Electronics
04-15-2024, 06:56 PM
Replies: 8
Views: 228
Posted By ratfink6923

Re: 1992 Camaro RS needs interior wirning

This was a manual seat car with rear defrost. Adding the power for the seat is relatively easy.
if you don't come up with anything let me know, I'd have to pull it yet.
Forum: Electronics
04-15-2024, 06:21 PM
Replies: 8
Views: 228
Posted By ratfink6923

Re: 1992 Camaro RS needs interior wirning

I have a power window 92 harness still in car that hasn't been molested aside from the stereo connections.
where are you located?
Forum: Cooling
04-15-2024, 06:14 PM
Replies: 19
Views: 395
Posted By ratfink6923

Re: Cooling Q…not sure of problem

Sounds like you've narrowed it down to bad switches. You can check continuity between the terminal and switch body in with a hotplate. Obviously boiling water won't exceed 212.
Forum: Exterior Parts for Sale
04-14-2024, 08:32 PM
Replies: 7
Views: 353
Posted By ratfink6923

Re: 92 CAMARO 25TH ANNIVERSARY BADGE

That's dirty
Forum: Body
04-11-2024, 10:16 PM
Replies: 1
Views: 157
Posted By ratfink6923

Re: Back spoiler loose

Near the decklid? If so, the studs come in vertically from the top, no need to pull the bumper, should be able to access with the plastic interior trim removed from the left quarter.
Forum: Brakes
04-11-2024, 08:16 AM
Replies: 8
Views: 304
Posted By ratfink6923

Re: Need help with drum brake installation

Is the edge of the forward shoe resting on the ridge of the backing plate? Pull the shoe towards you just a bit and see if it doesn't spring into place
Forum: Tech / General Engine
04-10-2024, 11:19 AM
Replies: 3
Views: 207
Posted By ratfink6923

Re: Small white plastic T gizmo?

That's a vacuum check valve for the HVAC system. For an makes universal ones in the "HELP" section
Forum: Engine/Drivetrain/Suspension Parts for Sale
04-03-2024, 08:44 PM
Replies: 5
Views: 430
Posted By ratfink6923

Re: LT4 Hot Cam Kit 12480002 New in Box

It was a great find, and I tried to price it fair. Its arguably a better cam than I'm sticking with (comp xe268) but the rockers, springs, and misc would have gone to waste with my heads.
Forum: Cooling
04-01-2024, 07:23 AM
Replies: 4
Views: 162
Posted By ratfink6923

Re: Part name or code needed

You're welcome. Be prepared for that piece to break flush with the manifold when you go to remove it. Lisle and a few others make special tools to remove the broken piece from the manifold. Most look...
Forum: Miscellaneous Third Gen Items!
03-31-2024, 08:00 PM
Replies: 7
Views: 334
Posted By ratfink6923

Re: Local guy liquidating his collection in Zephyrhills, FL

I just saw the same. He did mention he had some more parts in his upstairs area I believe
Forum: Miscellaneous Third Gen Items!
03-31-2024, 07:34 PM
Replies: 7
Views: 334
Posted By ratfink6923

Re: Local guy liquidating his collection in Zephyrhills, FL

https://m.facebook.com/marketplace/item/758070422945483/
Forum: Miscellaneous Third Gen Items!
03-31-2024, 07:26 PM
Replies: 7
Views: 334
Posted By ratfink6923

Re: Local guy liquidating his collection in Zephyrhills, FL

Id be willing to work that out. He only has white lettered radios, I have been keeping an eye out for a yellow lettered cd player. He said he only works on it on weekends, so probably won't receive...
Forum: Engine/Drivetrain/Suspension Parts for Sale
03-31-2024, 05:33 PM
Replies: 5
Views: 430
Posted By ratfink6923

SOLD!! LT4 Hot Cam Kit 12480002 New in Box

Purchased this from a local seller. Decided to stay with the Comp Cam I've already installed in my L31 long block build due to vortec head constraints. All pieces are still new in box, never...
Forum: Miscellaneous Third Gen Items!
03-31-2024, 04:48 PM
Replies: 7
Views: 334
Posted By ratfink6923

Local guy liquidating his collection in Zephyrhills, FL

I wasn't sure where to post this as it's not my collection.
found an ad on marketplace and went today to see for myself.

Guy has been collecting parts/cars since the late 90s. He has six irocs...
Forum: Cooling
03-31-2024, 04:37 PM
Replies: 4
Views: 162
Posted By ratfink6923

Re: Part name or code needed

If you're replacing it for a leak, make sure it's the piece circled and not the quick disconnect it connects to (that's typically the leak point)
if that's definitely the leaker, I will see if the...
Forum: TBI
03-25-2024, 08:20 PM
Replies: 16
Views: 605
Posted By ratfink6923

Re: New girl in town

Do you have access to a lift? That makes the job 100x easier.

​​​​​
Forum: Electronics
03-19-2024, 12:20 PM
Replies: 4
Views: 212
Posted By ratfink6923

Re: Amp is killing battery

The large positive and ground should have constant power. The remote is the only one that will be switched. If you can measure voltage at the remote terminal with the blue wire disconnected then the...
Forum: Aftermarket Product Review
03-18-2024, 04:16 PM
Replies: 16
Views: 767
Posted By ratfink6923

Re: Never Order Delphi Fuel Pump from Rock Auto

I work for a GM dealer and we've had some pretty terrible luck with them lately as well.
Forum: Electronics
03-17-2024, 04:47 PM
Replies: 3
Views: 133
Posted By ratfink6923

Re: Sigh... managed to break both ears off the fuse panel retainer....

On the fuse block itself? Have pictures?
Forum: Tech / General Engine
03-15-2024, 08:15 PM
Replies: 4
Views: 198
Posted By ratfink6923

Re: Replacing fuel hardlines - any pointers?

That's going to definitely make it interesting. I removed mine in the air and it was relatively simple. I have no decent advice for the ground. Sorry.
Forum: Tech / General Engine
03-15-2024, 11:46 AM
Replies: 4
Views: 198
Posted By ratfink6923

Re: Replacing fuel hardlines - any pointers?

If the lines are in one piece, I would leave them that way. Are you doing this on a lift or jack stands? A lift makes it dramatically easier as you can maneuver the lines a hell of a lot easier. Yes,...
Forum: V6
03-07-2024, 12:04 PM
Replies: 23
Views: 434
Posted By ratfink6923

Re: ICM testing?

That disparity shouldn't cause a no start
Forum: V6
03-07-2024, 10:03 AM
Replies: 23
Views: 434
Posted By ratfink6923

Re: ICM testing?

-40 is the default value for an open circuit. Id be willing to bet that's where your issue lies. Possible bad wire between ECM and ect. Are you familiar with continuity tests? The next thing I would...
Forum: V6
03-06-2024, 05:11 PM
Replies: 23
Views: 434
Posted By ratfink6923

Re: ICM testing?

It would be great if you could get a scanner on there and see data. Could be the pickup coil failing, could be a coolant temp sensor reporting extremely low temp and making it run extremely rich. ...
Forum: V6
03-06-2024, 02:36 PM
Replies: 23
Views: 434
Posted By ratfink6923

Re: ICM testing?

It could be but it usually is in an intermittent type of thing. Are the spark plugs fuel fouled? Have you pulled them to inspect them?
Forum: V6
03-06-2024, 01:51 PM
Replies: 23
Views: 434
Posted By ratfink6923

Re: ICM testing?

First thing, resistance isn't a definitive answer on a coil, but let's ignore that for now. Do you have access to a noid light set or an old school, incandescent test.light? We need to see if you're...
Showing results 1 to 50 of 206
 
Page 1 of 5
1
2
3
4
5


 
Forum Jump


All times are GMT -5. The time now is 04:31 PM.