Third Generation F-Body Message Boards

Search: Posts Made By: JNRSingh
Showing results 1 to 39 of 39
Search took 0.07 seconds.
Forum: Car Audio
04-05-2021, 09:14 PM
Replies: 421
Views: 94,182
Posted By JNRSingh

Re: Double Din Radio Bezel

I would like to order one also. The ebay link had 0 items listed...is there an updated link where I can check out and buy your product?
Forum: Exterior Parts Wanted
02-28-2015, 12:22 AM
Replies: 2
Views: 432
Posted By JNRSingh

Re: Wade Passenger Headlight Cover - Smoke wanted

Thank you for the offer, however I would really like to find the 1 Wade.
Forum: Exterior Parts Wanted
10-07-2014, 11:51 PM
Replies: 2
Views: 432
Posted By JNRSingh

Wade Passenger Headlight Cover - Smoke wanted

I am looking for a passenger side Wade#922-31286
Headlight Cover
Smoke
1985-92 Chevy Camaro IROC-Z28

My passenger side flew off while on the highway and I can't find any single ones for sale...
Forum: Tech / General Engine
09-01-2014, 12:26 AM
Replies: 40
Views: 2,741
Posted By JNRSingh

Re: Car not starting

Ok gentlemen, I have finally resolved the issue! Thank you to everyone who contributed to this post!

I checked the coolant temp sensor by comparing its resistance at different temperatures to that...
Forum: Tech / General Engine
07-20-2014, 11:44 PM
Replies: 40
Views: 2,741
Posted By JNRSingh

Re: Car not starting

Ok so just an update on what is going on:

I received the injectors back from Southbay and they all were cleaned and in working order. I re-installed them and also changed the spark plus for good...
Forum: Tech / General Engine
05-23-2014, 08:37 PM
Replies: 40
Views: 2,741
Posted By JNRSingh

Re: Car not starting

red rock I will first see if the injector issue solves my issue then pull a few plugs to see their condition after that fix. Eventually I will change the plugs. Do you recommend any particular...
Forum: Tech / General Engine
05-23-2014, 06:57 PM
Replies: 40
Views: 2,741
Posted By JNRSingh

Re: Car not starting

Jcase350 , yea I am running ACDelcos. And yea JEGS does not describe their products accurately, I've had similar compatibility issues with them. Check your idle air control (IAC) valve on your...
Forum: Tech / General Engine
05-23-2014, 06:15 PM
Replies: 40
Views: 2,741
Posted By JNRSingh

Re: Car not starting

Yea I cleaned off the plugs using a little dremel wire brush tool on a drill gun last night as I had them out. I have a 305 5.0L engine so I have 19lb injectors, I believe the 22s are for 350s, but...
Forum: Tech / General Engine
05-23-2014, 05:22 PM
Replies: 40
Views: 2,741
Posted By JNRSingh

Re: Car not starting

Thanks Rusty Vango, I will try and get that CEL fixed ASAP. Also blue iroc and Jcase350 I think I have found the primary issue.

Yesterday I began working on the car again and the battery had held...
Forum: Tech / General Engine
04-22-2014, 11:36 PM
Replies: 40
Views: 2,741
Posted By JNRSingh

Re: Car not starting

blue iroc, I have been busy lately and have not resolved the issue yet. I plan to tackle it next month with the help of a friend and will post my results. My goal is to get the car fixed, insured and...
Forum: Tech / General Engine
11-22-2013, 05:29 PM
Replies: 40
Views: 2,741
Posted By JNRSingh

Re: Car not starting

Ok so I took a step forward and now I have taken the same amount back...the car is not starting at all now. I installed an inline check valve right after my fuel filter as it was the closest spot I...
Forum: Tech / General Engine
11-09-2013, 02:17 AM
Replies: 40
Views: 2,741
Posted By JNRSingh

Re: Car not starting

Ok so here is my progress so far:

Lynn1990IrocZ thanks for your advice, but all my injectors are above 12 ohms. So I pulled the fuel rails with the fuel lines and injectors connected to it and...
Forum: TPI
11-09-2013, 01:56 AM
Replies: 10
Views: 2,236
Posted By JNRSingh

Re: Erratic Idle after Injector Swap

I though I solved the issue with the new fuel line...but I did not...my issue continues in this thread:

https://www.thirdgen.org/forums/tech-general-engine/691690-car-not-starting.html#post5661506...
Forum: Tech / General Engine
11-04-2013, 05:05 AM
Replies: 40
Views: 2,741
Posted By JNRSingh

Re: Car not starting

I suspect the bulb may be bad...I am not sure how to get to it though....

I think I am loosing fuel pressure based on a simple test...when I remove the gas tank cap after attempting to start the...
Forum: Tech / General Engine
11-03-2013, 11:53 PM
Replies: 40
Views: 2,741
Posted By JNRSingh

Re: Car not starting

Hey vetteoz, thanks for the advice, I updated my profile a bit...I could not test for the codes because my check engine light/ses light among other do not work, I don't know why and all my fuses in...
Forum: Tech / General Engine
11-03-2013, 06:56 AM
Replies: 40
Views: 2,741
Posted By JNRSingh

Re: Car not starting

The plugs are about two years old and looked black when removed...none were wet or anything... just coated with carbon all the same way...I do not have a gauge to check fuel pressure...I will try and...
Forum: Tech / General Engine
11-03-2013, 05:32 AM
Replies: 40
Views: 2,741
Posted By JNRSingh

Car not starting

So I have a 91 Camaro z28 305 TPI...recently the car was driving very poorly and I found that 4 fuel injectors were bad so I replaced all 8 with 19lbs Bosch IIIs from South Bay fuel injector co. The...
Forum: TPI
10-18-2013, 01:13 AM
Replies: 3
Views: 960
Posted By JNRSingh

Re: how do you clean fuel lines

Hmmm sorry to hear that...thanks for the heads up paulo57509
Forum: TPI
10-17-2013, 09:57 PM
Replies: 10
Views: 2,236
Posted By JNRSingh

Re: Erratic Idle after Injector Swap

Thank you very much for your advice lonestar7. I did realize I was losing fuel pressure and decided to change my fuel filter. Upon changing the fuel filter I found that the solid fuel line from the...
Forum: TPI
10-17-2013, 12:29 AM
Replies: 3
Views: 960
Posted By JNRSingh

Re: how do you clean fuel lines

Did you ever end up doing this? I was considering this....
Forum: TPI
10-16-2013, 02:41 PM
Replies: 10
Views: 2,236
Posted By JNRSingh

Re: Erratic Idle after Injector Swap

I was hoping this would not be the case as the fuel line connections had quite a bit of corrosion and its possible while reconnecting the metal lines that some rust could get in....however I do not...
Forum: TPI
10-15-2013, 03:50 PM
Replies: 10
Views: 2,236
Posted By JNRSingh

Re: Erratic Idle after Injector Swap

So another note about my issue...when the car is idling rough it chugs like a diesel truck engine and pours smoke out the exhaust ans spews out black carbon...if I rev the engine into the redline...
Forum: TPI
10-15-2013, 12:32 AM
Replies: 10
Views: 2,236
Posted By JNRSingh

Re: Erratic Idle after Injector Swap

I had the negative battery cable disconnected during the swap and reconnected it after, so I'm guessing it was reset.
Forum: TPI
10-14-2013, 10:34 PM
Replies: 10
Views: 2,236
Posted By JNRSingh

Erratic Idle after Injector Swap

Hey guys so I have an automatic 91 305 TPI. I recently found that 4 of my fuel injectors where bad (after my car was stalling out, lacked power, and would not shift gears smoothly) by testing and...
Forum: Cooling
09-26-2013, 12:50 AM
Replies: 6
Views: 1,401
Posted By JNRSingh

Re: Temp Sensor Wire

Hey Jonesyfxr, Nina, and Sofakingdom thanks all of you for your responses...I was finally able to find the wire...I located it on the main harness directly behind the driver side head as Jonesyfxr...
Forum: Engine/Drivetrain/Suspension Parts for Sale
09-22-2013, 01:52 AM
Replies: 77
Views: 3,722
Posted By JNRSingh

Re: parting out 1991 z28 5.7 tpi

Hi i was wondering if i could get quotes w/ shipping to 13850 for the following:

-the bracket of the sunvisor that bolts onto the car top and attaches to the visor
-the 3 bolts for the...
Forum: Cooling
09-21-2013, 05:22 PM
Replies: 6
Views: 1,401
Posted By JNRSingh

Re: Temp Sensor Wire

Thank you for your quick reply sofakingdom, I just checked and the only wires in that harness are the wires for the fuel injectors and the alternator...any pics or other suggestions?
Forum: Cooling
09-21-2013, 02:53 PM
Replies: 6
Views: 1,401
Posted By JNRSingh

Temp Sensor Wire

Hey guys, my issue is that I cannot find the wire that connects to the engine temperature sensor that is screwed into the driver side engine head. Based on my searches through the message board, it...
Forum: Exhaust
01-19-2011, 07:25 PM
Replies: 12
Views: 599
Posted By JNRSingh

Re: Headers Question

the y pipe isn't stock...its dynomax performance but built to hook up to the stock cat and stock manifolds...i was just wondering if there were headers that would be at the same angle/bolt directly...
Forum: Exhaust
01-17-2011, 01:53 AM
Replies: 12
Views: 599
Posted By JNRSingh

Re: Headers Question

bump
Forum: Suspension and Chassis
01-04-2011, 03:33 AM
Replies: 8
Views: 628
Posted By JNRSingh

Re: Best Brands for Specific parts

Yeah that makes sense. Thanks all for your input! I recently bought quite a few BMR suspension components as I was able to get them for a good deal. I plan on installing them in the following months...
Forum: Exhaust
01-04-2011, 03:31 AM
Replies: 12
Views: 599
Posted By JNRSingh

Headers Question

Ive got a 91 z28 305 tpi with a dynomax catback exhaust, stock cat, aftermarket y pipe with mandrel bends, and stock exhaust manifold w/ egr delete. I was wondering if anyone knows of a set of...
Forum: Suspension and Chassis
12-30-2010, 01:28 AM
Replies: 8
Views: 628
Posted By JNRSingh

Best Brands for Specific parts

hey i was just wanted some opinions on what are the best brands to buy for wonder bars, subframe connectors, strut towers braces and sway bars are. In my opinion just by looks, BMRs wonderbar looks...
Forum: Tech / General Engine
12-22-2010, 04:58 AM
Replies: 4
Views: 627
Posted By JNRSingh

Re: Intake Runners Removal: Help Needed

omg thank you so much!! i did not realize this..i didnt even think to check the other side, i was trying to remove the bolt from the front.
Forum: Tech / General Engine
12-22-2010, 02:59 AM
Replies: 4
Views: 627
Posted By JNRSingh

Re: Intake Runners Removal: Help Needed

thats what i thought at first, no its not the gasket, i am sure of this as i tried prying off the runners with a hammer, its a smaller bolt on the bottom closer to the car...im not sure how to get it...
Forum: Tech / General Engine
12-21-2010, 11:32 PM
Replies: 4
Views: 627
Posted By JNRSingh

Intake Runners Removal: Help Needed

Hey guys, I am currently trying to remove the intake runners on my 91 z28 305 TPI. I removed all the main bolts on the driver side, but i can't seem to get the runners off, they are very loose like a...
Forum: Third Gen Association of Ontario
12-03-2010, 09:56 AM
Replies: 17
Views: 5,144
Posted By JNRSingh

Re: GTA Cone Filter...

hey i was wondering if the cone is worth getting for performance...is it better than using the stock airbox with k&n rectangular filters...because the cone really would take in a lot of heat from the...
Forum: Tech / General Engine
09-27-2010, 11:24 AM
Replies: 7
Views: 12,048
Posted By JNRSingh

Re: Overheating and low oil pressure

thanks man i will double check teh fans and clean out the "fins" of the radiator...i was actually also planning on cutting real vents onto the hood where the hood louvers with the false vents are as...
Forum: Tech / General Engine
09-25-2010, 12:49 AM
Replies: 7
Views: 12,048
Posted By JNRSingh

Re: Overheating and low oil pressure

hey i was wondering if the original poster ever resolved this problem, and if so how. I have a 92 z28 5.0L. I put on a dynomax performance exhaust, a throttle body air foil, K&N high flow filters,...
Showing results 1 to 39 of 39


 
Forum Jump


All times are GMT -5. The time now is 10:27 AM.