Third Generation F-Body Message Boards

Search: Posts Made By: bassxlr8r
Showing results 1 to 13 of 13
Search took 0.04 seconds.
Forum: Interior
06-05-2023, 02:38 AM
Replies: 4
Views: 709
Posted By bassxlr8r

Re: '91 Camaro Z28 - Headliner Material

If you are still looking, it may be worth giving Ben at Colorado Auto Trim Supply a call. Large selection of a lot of hard to find materials, many are NOS and older aftermarket. Much easier to deal...
Forum: Engine Swap
11-07-2022, 09:53 PM
Replies: 19
Views: 954
Posted By bassxlr8r

Re: 5.3 Swap questions

Hope you didn't check out on that purchase yet, those are LT1 accessories (not compatible with 5.3).
Forum: Electronics
05-23-2021, 12:43 AM
Replies: 3
Views: 405
Posted By bassxlr8r

Re: Ignition Switch Replacement Roadblocks

If you haven't already, I'd start at the battery terminal connections. Since you've had them off, that would be the first thing to check. Clean the contacts, or at minimum wiggle them around with the...
Forum: Interior
03-20-2021, 10:53 AM
Replies: 17
Views: 1,305
Posted By bassxlr8r

Re: Suggestions for Sound/Vibrational dampening material such as Dynamat

As far as the Peel and Seal, my experience is not as good. I had a customer bring a roll in for an El Camino I was working on to try to save money. Even with surface prep and using a solid wood...
Forum: Wheels and Tires
03-20-2021, 09:57 AM
Replies: 49
Views: 2,796
Posted By bassxlr8r

Re: xxr 18x10.6

I used a lug centric spacer/adapter, and in my opinion once bolted becomes an extension of the hub. Bolted on properly, it just extends the wheel's mounting plane out further. I had to flatten the...
Forum: Wheels and Tires
01-26-2021, 01:56 AM
Replies: 49
Views: 2,796
Posted By bassxlr8r

Re: xxr 18x10.6

A 285 is still a hell of a lot more than what was there stock, and overall height remains virtually the same. The stock 245/50/16 is 25.65 inches tall, where the 285/35/18 is 25.85. Even with the...
Forum: Wheels and Tires
01-25-2021, 08:17 AM
Replies: 49
Views: 2,796
Posted By bassxlr8r

Re: xxr 18x10.6

Yes, I believe you can. When I was looking, it seems there was someone running a 315/30 on these all the way around. Can't remember if that one was lowered or not, or if they had spacers. Mine is...
Forum: Wheels and Tires
01-11-2021, 11:03 PM
Replies: 49
Views: 2,796
Posted By bassxlr8r

Re: xxr 18x10.6

All of the 18x10.5 in the 5x120 pattern are +20 offset. The black car (dbltke) has a few more mods done to his suspension (lcarbs, camber plates, weight jacks) and metal clearance than mine, and his...
Forum: Wheels and Tires
01-10-2021, 03:30 PM
Replies: 49
Views: 2,796
Posted By bassxlr8r

Re: xxr 18x10.6

I used a 1.25" adapter on the fronts (also flattened bearing dust cap for center cap clearance) and a .75" adapter on the rear, with 285/35 all around. Mine is lowered by taking 1 coil off of the...
Forum: Car Audio
01-06-2021, 05:24 AM
Replies: 1
Views: 1,265
Posted By bassxlr8r

Re: Need some alarm help

The door lock system in your car requires a positive trigger to activate locking/unlocking. On many older alarm systems, the door lock outputs had provisions built into the brain unit that would...
Forum: Electronics
04-27-2019, 10:22 AM
Replies: 1
Views: 8,181
Posted By bassxlr8r

Re: Alarm install - remote locking - where to splice?

To answer the "where to splice" question, your Firebird's factory door locks use a positive triggered relay. The wires from either switch are not isolated, meaning that you can run a lock and unlock...
Forum: Electronics
04-12-2019, 10:03 AM
Replies: 1
Views: 377
Posted By bassxlr8r

Re: Push button

Depending on the button type you have, there are a few ways to go about it. Instructions below are based on a simple 2 or 3 pin momentary push button/switch.

If you are just wanting crank function...
Forum: Classified Ads Feedback Board
09-01-2015, 12:07 PM
Replies: 0
Views: 631
Posted By bassxlr8r

Navy8125

Prompt and excellent communication, had the parts shipped out the same day payment was received. Packaged well, and provided tracking information. Couldn't ask for a better transaction or seller. ...
Showing results 1 to 13 of 13


 
Forum Jump


All times are GMT -5. The time now is 03:22 AM.