Third Generation F-Body Message Boards

Search: Posts Made By: MrCaswell
Showing results 1 to 34 of 34
Search took 0.01 seconds.
Forum: Tech / General Engine
04-17-2024, 11:35 PM
Replies: 20
Views: 862
Posted By MrCaswell

Re: Low Voltage to Distributor

Well, I am happy to announce that the issue has been finally resolved. After replacing my ignition switch, rewiring my fusible links, hours of multimeter testing and chasing wires, the problem turned...
Forum: Tech / General Engine
03-01-2024, 12:50 PM
Replies: 20
Views: 862
Posted By MrCaswell

Re: Low Voltage to Distributor

Not yet. I was out of town for a week, but will continue to work on it as weather permits. Because the ignition switch was not faulty and the fusible links appear to have been replaced at some point...
Forum: Tech / General Engine
02-13-2024, 07:16 PM
Replies: 20
Views: 862
Posted By MrCaswell

Re: Low Voltage to Distributor

I measured the voltage at the red wire indicated by the arrow, and the pink wire. Both tested at a maximum of 11V. I also ended up replacing the ignition switch itself, but this did not solve the...
Forum: Tech / General Engine
02-13-2024, 12:27 PM
Replies: 20
Views: 862
Posted By MrCaswell

Re: Low Voltage to Distributor

Also, fusible link B has been replaced using 16 GA fusible link wire.
Forum: Tech / General Engine
02-13-2024, 12:24 PM
Replies: 20
Views: 862
Posted By MrCaswell

Re: Low Voltage to Distributor

Quick update. I tested voltage to the Ignition Switch and got a reading of ~11 V, which is consistent with the reading across the terminals of the battery using the same multimeter. Now beginning to...
Forum: Tech / General Engine
02-09-2024, 06:28 PM
Replies: 20
Views: 862
Posted By MrCaswell

Re: Low Voltage to Distributor

And yes, I did disconnect the pink wire before testing.
Forum: Tech / General Engine
02-09-2024, 11:04 AM
Replies: 20
Views: 862
Posted By MrCaswell

Re: Low Voltage to Distributor

Thank you so much Vader. This is invaluable.
Forum: Tech / General Engine
02-09-2024, 11:02 AM
Replies: 20
Views: 862
Posted By MrCaswell

Re: Low Voltage to Distributor

Well, one of the POs did attempt to wire a bass speaker into the rear hatch at one point, and there are some sketchy looking wires around the fuse box..
Forum: Tech / General Engine
02-09-2024, 12:24 AM
Replies: 20
Views: 862
Posted By MrCaswell

Re: Low Voltage to Distributor

Yes, it is. 1986 quadrajet 305 with the 5-speed T-5 gearbox.
Forum: Tech / General Engine
02-08-2024, 06:32 PM
Replies: 20
Views: 862
Posted By MrCaswell

Re: Low Voltage to Distributor

Additionally, do you know where I can find an appropriate set of wire diagrams for this vehicle?

This is what I have been referencing:...
Forum: Tech / General Engine
02-08-2024, 06:27 PM
Replies: 20
Views: 862
Posted By MrCaswell

Re: Low Voltage to Distributor

Excellent, thank you. It is always a good day to learn something new.
Forum: Electronics
02-08-2024, 04:58 PM
Replies: 2
Views: 373
Posted By MrCaswell

Re: Low Voltage to FiTech EFI

Here are the wiring diagrams that I have.
https://cimg2.ibsrv.net/gimg/www.thirdgen.org-vbulletin/1000x1101/fig24_1986_5_0l_carbureted_engine_wiring_1_f68928ab9af292fda192f6256d00204d70731051.gif...
Forum: Electronics
02-08-2024, 04:40 PM
Replies: 2
Views: 373
Posted By MrCaswell

Low Voltage to FiTech EFI

Hey guys, I'm looking for some electrical expertise. On my 1986 Trans Am I am running a FiTech throttle body EFI system which requires a 12v signal from the ignition circuit via a white 'key' wire....
Forum: Tech / General Engine
02-08-2024, 04:15 PM
Replies: 20
Views: 862
Posted By MrCaswell

Low Voltage to Distributor

Hey guys, I'm looking for some electrical expertise.

On my 1986 Trans Am I am running a FiTech throttle body EFI system which requires a 12v signal from the ignition circuit via a white 'key'...
Forum: Body
09-26-2021, 03:19 PM
Replies: 2
Views: 332
Posted By MrCaswell

Re: Does Anyone Have These Paint Codes?

Thanks! I was able to find this on another thread.
https://cimg9.ibsrv.net/gimg/www.thirdgen.org-vbulletin/720x631/20210926_161822_73451309901992f8aa8074b9303f9d24e21cabad.jpg
Forum: Body
09-25-2021, 11:04 AM
Replies: 2
Views: 332
Posted By MrCaswell

Does Anyone Have These Paint Codes?

https://cimg6.ibsrv.net/gimg/www.thirdgen.org-vbulletin/791x444/1_46475defc79c4ab33152aeb68e5fbcab8e1b40e8.jpg...
Forum: Cooling
07-06-2021, 04:26 PM
Replies: 8
Views: 456
Posted By MrCaswell

Re: Radiator Cooling Fan Not Coming On

Does the switch ground via the threads?
Forum: Cooling
07-06-2021, 04:01 PM
Replies: 8
Views: 456
Posted By MrCaswell

Re: Radiator Cooling Fan Not Coming On

https://cimg0.ibsrv.net/gimg/www.thirdgen.org-vbulletin/2000x1504/20210706_170042_71a2ab01eabf021fe4a8d00bbed62f4b94318741.jpg
This is what I'm looking for?
Forum: Cooling
07-06-2021, 03:56 PM
Replies: 8
Views: 456
Posted By MrCaswell

Re: Radiator Cooling Fan Not Coming On

Yes, on the passenger side. I have not seen any frayed wiring. I'll take a look.
Forum: Cooling
07-06-2021, 03:02 PM
Replies: 8
Views: 456
Posted By MrCaswell

Radiator Cooling Fan Not Coming On

Hello everyone. I've noticed recently that my radiator cooling fan (single fan, originally LG4 car with A/C delete) hasn't been turning on even between 220 and 260 degrees. I've tested the fan itself...
Forum: Tech / General Engine
06-13-2021, 07:23 PM
Replies: 5
Views: 764
Posted By MrCaswell

Re: Coolant Temp Sender and Fan Switch Relocation

Yes, I realize that. The car is currently running 2" side pipes with no cats. Stock manifolds unfortunately, but that can change in the near future.
Forum: Tech / General Engine
06-13-2021, 06:50 PM
Replies: 5
Views: 764
Posted By MrCaswell

Re: Coolant Temp Sender and Fan Switch Relocation

Ah, somehow I didn't notice the threaded holes until you pointed it out. Doh.
As far as the choice of intake and carb I based it on this:...
Forum: Tech / General Engine
06-13-2021, 06:30 PM
Replies: 5
Views: 764
Posted By MrCaswell

Re: Coolant Temp Sender Relocation

I'd also like to mention if it is of any help that this particular car is, or was, an LG4 car with the T5 transmission.
Forum: Tech / General Engine
06-13-2021, 06:13 PM
Replies: 5
Views: 764
Posted By MrCaswell

Coolant Temp Sender and Fan Switch Relocation

Hey everyone, I've been assembling the top end of the 305 in my 1986 Trans Am and have now come to the stage where I am beginning to bolt on accessories, exhaust manifolds, and carb. Included in the...
Forum: Tech / General Engine
05-30-2021, 10:14 PM
Replies: 7
Views: 477
Posted By MrCaswell

Re: Torquing Down Obscured Head Bolts

https://cimg8.ibsrv.net/gimg/www.thirdgen.org-vbulletin/2000x1504/20210530_210810_530cad19c714d40587c98616dfa0b3bba698161c.jpg...
Forum: Tech / General Engine
05-30-2021, 02:48 PM
Replies: 7
Views: 477
Posted By MrCaswell

Re: Torquing Down Obscured Head Bolts

Thanks for the reply. I was referring to torquing down the new head bolts after the new heads are installed. I suppose I'll just have to remove the manifolds entirely.
Forum: Tech / General Engine
05-30-2021, 01:54 PM
Replies: 7
Views: 477
Posted By MrCaswell

Torquing Down Obscured Head Bolts

Good Evening everyone, today I am continuing the process of installing a new set of World Products 305 S/R heads on my 1986 Trans Am. Currently I'm removing the old head bolts on the passenger side...
Forum: Tech / General Engine
05-16-2021, 10:07 PM
Replies: 9
Views: 882
Posted By MrCaswell

Re: Small Crack in Used 305 S/R Head Casting

Yes, that would be correct. Seems that not only did I get a damaged cylinder head, but I also recieved the wrong casting altogether. Yikes. Fortunately the other cyclinder head purchased directly...
Forum: Tech / General Engine
05-16-2021, 05:45 PM
Replies: 9
Views: 882
Posted By MrCaswell

Re: Small Crack in Used 305 S/R Head Casting

Looks to be casting number 1901695V. 4360.
https://cimg6.ibsrv.net/gimg/www.thirdgen.org-vbulletin/2000x1504/20210516_184355_e0e7d31449c27affbd9be96269c03f6e6b08359a.jpg
Forum: Tech / General Engine
05-16-2021, 01:03 PM
Replies: 9
Views: 882
Posted By MrCaswell

Re: Small Crack in Used 305 S/R Head Casting

Yes, it is without a doubt due to shipping damage. The corner of the machined surface is slightly bent upwards and there is a visible indentation now that you mentioned it....
Forum: Tech / General Engine
05-16-2021, 12:18 PM
Replies: 9
Views: 882
Posted By MrCaswell

Re: Small Crack in Used 305 S/R Head Casting

I submitted a request for a return, so hopefully I'll hear back from the seller shortly. Thanks for your time.
Forum: Tech / General Engine
05-16-2021, 11:25 AM
Replies: 9
Views: 882
Posted By MrCaswell

Small Crack in Used 305 S/R Head Casting

Hello everyone, I purchased recently a set of World Products cylinder heads, one from new and the other I found used on ebay. Unfortunately upon closer inspection I discovered this exterior crack on...
Forum: Body
09-28-2020, 01:46 AM
Replies: 3
Views: 481
Posted By MrCaswell

Re: Fasteners for Window Weatherstrip

Thanks for the reply. This looks like the closest I could find on their site.
https://www.fastenal.com/products/details/11236402
Forum: Body
09-27-2020, 11:32 PM
Replies: 3
Views: 481
Posted By MrCaswell

Fasteners for Window Weatherstrip

Hello all, this is my first post on the forums. I bought my 1986 TA a few months ago and one of the first things I have done is replacement of the original window beltline weatherstripping which was...
Showing results 1 to 34 of 34


 
Forum Jump


All times are GMT -5. The time now is 04:19 AM.