Third Generation F-Body Message Boards

 
Page 1 of 2
1
2
Search: Posts Made By: curtalert89
Showing results 1 to 50 of 90
Search took 0.05 seconds.
Forum: Body
06-16-2019, 03:23 PM
Replies: 0
Views: 2,524
Posted By curtalert89

Wiper transmission linkages, and problems

https://cimg9.ibsrv.net/gimg/www.thirdgen.org-vbulletin/2000x1504/57efe281_e9a4_481b_91e5_ea728fa71448_8b904de2dc939308e9f937e6ecb060d02bbc7495.jpeg...
Forum: Interior
12-03-2017, 10:39 PM
Replies: 111
Views: 126,898
Posted By curtalert89

Re: The 4th Gen Dash Swap Guide.

so im guessing the white wire would be the dome lights? I don’t have the original body harness, it was to hacked up so I installed a new one. But most of the colors are GM spec.
Forum: Interior
11-26-2017, 04:01 PM
Replies: 111
Views: 126,898
Posted By curtalert89

Re: The 4th Gen Dash Swap Guide.

I’m doing a fourth gen dash swap. Dash is out of a 94 firebird I believe. Most of the wiring is done, except I can’t figure out one wire. It’s the Grey wire on the dimmer knob. The connector has four...
Forum: Engine Swap
12-10-2014, 08:29 PM
Replies: 28
Views: 15,748
Posted By curtalert89

Re: one wire alternator?

I have an alternator from a 96 chevy truck it's a single wire plug with it. My original is a two wire plug. What would I have to do to get it to work on my car.

1991 Camaro with an 88 350 tbi...
Forum: Electronics
12-10-2014, 08:20 PM
Replies: 6
Views: 40,330
Posted By curtalert89

Re: What is the 2 wire plug in the alternator for?

So I have a single wire plug alternator from a 96 chevy truck that I'm wanting to install on my car. Anyone done this. How would I hook this up!
Forum: Carburetors
12-04-2014, 05:45 PM
Replies: 11
Views: 15,685
Posted By curtalert89

Re: holley fuel pressure regulator problems

So glad I found this post. And sorry I have to bring it back. I'm having the same problem. Except my 3 port holley regulator is only letting 2psi come through. I'll explaing what I've done to the...
Forum: Transmissions and Drivetrain
08-07-2014, 08:51 PM
Replies: 7
Views: 640
Posted By curtalert89

Re: 4th gen rear in 92RS

Well I have yet to drive it on the road, just around my driveway, I still need exhaust and make it legal. The car use to be a 3.1 v6, I swaped it for a carbed 350 and this new rear. I do like how...
Forum: Transmissions and Drivetrain
08-06-2014, 09:03 PM
Replies: 7
Views: 640
Posted By curtalert89

Re: 4th gen rear in 92RS

Ah cool, thank you good sir!!
Forum: Transmissions and Drivetrain
08-06-2014, 04:02 PM
Replies: 7
Views: 640
Posted By curtalert89

Re: 4th gen rear in 92RS

I just did the same swap in my 91 Camaro, rearend came out of a 94. And I believe it is also the 3:43 gears. It's all mounted up perfectly, I was just wanting to know what the pigtail at the top of...
Forum: Engine Swap
04-02-2014, 08:33 PM
Replies: 4
Views: 1,206
Posted By curtalert89

Re: 3.1 to 350 wire harness question.

Okay thanks guys for all the input, but I stumbled across what I think my problem with the starting with key problem. Could it be that it's because my neutral safety switch is not hooked up. I'm...
Forum: Carburetors
03-19-2014, 07:33 PM
Replies: 7
Views: 11,934
Posted By curtalert89

Re: 3.1 to 350 carb swap how did you do your wiring harness

I also kept electric fan(just wiring it up to a switch). And my starter the only wires it has running to it it the main battery cable and the purple wire(which goes directly to the c100 bulk head....
Forum: Engine Swap
03-19-2014, 07:01 PM
Replies: 4
Views: 1,206
Posted By curtalert89

3.1 to 350 wire harness question.

Okay guys I just completed my 1991 v6 to 350 carb swap. And I'm wanting to know how you set up your wire harness for your car.

I built mine but it has a few problems.

Won't turn over with the...
Forum: Carburetors
03-19-2014, 10:18 AM
Replies: 7
Views: 11,934
Posted By curtalert89

Re: 3.1 to 350 carb swap how did you do your wiring harness

Okay, are you running your ECU?
I'm not running one. I did away with most of the harness, and kept temp sender fuel pump relay. I'm having some issues tho. The car starts up perfect but my key...
Forum: Electronics
03-17-2014, 10:46 PM
Replies: 7
Views: 652
Posted By curtalert89

Re: Wire mix up

There is a thread on here that explains how to do it.

Okay and I'll check that as well.

Also when I turn the key to the "on" position the pink wire for the distributor gets power, when I turn...
Forum: Electronics
03-17-2014, 07:33 PM
Replies: 7
Views: 652
Posted By curtalert89

Re: Wire mix up

I did do the starter bypass and also pulled the fuse for Vats
Forum: Carburetors
03-17-2014, 07:28 PM
Replies: 7
Views: 11,934
Posted By curtalert89

3.1 to 350 carb swap how did you do your wiring harness

Okay guys I just completed my 1991 v6 to 350 carb swap. And I'm wanting to know how you set up your wire harness for your car.

I built mine but it has a few problems.

Won't turn over with the...
Forum: Electronics
03-17-2014, 04:54 PM
Replies: 7
Views: 652
Posted By curtalert89

Re: Wire mix up

Yes the c100 bulkhead is what I mean. And yes ground strap is connected . Ands as far as the purple starter wire is not getting power unless it's from my engine bay push button. And yes it has vats...
Forum: Electronics
03-17-2014, 08:57 AM
Replies: 7
Views: 652
Posted By curtalert89

Wire mix up

Okay guys I just completed my 1991 v6 to 350 carb swap. Motor starts up, but not with the key. The key only turns on acc. And fuel pump and to shut the engine down I have to pull the pos off the...
Forum: TBI
02-03-2014, 11:01 PM
Replies: 23
Views: 906
Posted By curtalert89

Re: Any ideas? 3.1 swap to 350tbi

Okay, so I did some reading and looking up and the harness that I'm using turned out to be one from a 454tbi truck.
Forum: TBI
01-22-2014, 08:02 PM
Replies: 23
Views: 906
Posted By curtalert89

Re: Any ideas? 3.1 swap to 350tbi

And all the sensors on the motor are getting power except for the coolant temp.
Forum: TBI
01-22-2014, 07:02 PM
Replies: 23
Views: 906
Posted By curtalert89

Re: Any ideas? 3.1 swap to 350tbi

Okay so I was looking at my VATs and the started relay has already been bypassed, but now I'm not sure about the vats it's still hooked up, vats fuse has power, but I'm not getting a security...
Forum: TBI
01-22-2014, 12:13 AM
Replies: 23
Views: 906
Posted By curtalert89

Re: Any ideas? 3.1 swap to 350tbi

I think I've narrowed it down to my VATS, I now have power to my fuel pump, and the red and white wires for the injectors that come on with the key! I'm just not getting any power to the blue and...
Forum: TBI
01-19-2014, 04:34 PM
Replies: 23
Views: 906
Posted By curtalert89

Re: Any ideas? 3.1 swap to 350tbi

Yes the ECM a6 pin is getting power
Blue d15 is not and green d14 is not!


And the red wire in the clearish plug (pin E) is for the red and white wires for the injector plugs, the white wire in...
Forum: TBI
01-19-2014, 12:42 PM
Replies: 23
Views: 906
Posted By curtalert89

Re: Any ideas? 3.1 swap to 350tbi

Yes, and it has power going to it!
Forum: TBI
01-19-2014, 11:52 AM
Replies: 23
Views: 906
Posted By curtalert89

Re: Any ideas? 3.1 swap to 350tbi

Yes, everything comes on as normally, even turns over. Just no power to the injectors or the ALDL.

And last night I think I may have come across why my inj. Have no power, there is a third plug...
Forum: TBI
01-19-2014, 10:37 AM
Replies: 23
Views: 906
Posted By curtalert89

Re: Any ideas? 3.1 swap to 350tbi

And the harness does have a knock sensor
Forum: TBI
01-19-2014, 10:32 AM
Replies: 23
Views: 906
Posted By curtalert89

Re: Any ideas? 3.1 swap to 350tbi

If I switch to a non VATs ECM would that give me problems with the car still not starting up?
Forum: TBI
01-18-2014, 08:55 PM
Replies: 23
Views: 906
Posted By curtalert89

Re: Any ideas? 3.1 swap to 350tbi

Sticker is worn away, took off plate and this is the info:

S/N # 153 721
Hypertech (c) '92
Pt# 122 362

G88IF
9235
M2732A-2FI
2IV FAST
Forum: TBI
01-18-2014, 06:34 PM
Replies: 23
Views: 906
Posted By curtalert89

Re: Any ideas? 3.1 swap to 350tbi

5.7
Forum: TBI
01-18-2014, 06:31 PM
Replies: 23
Views: 906
Posted By curtalert89

Re: Any ideas? 3.1 swap to 350tbi

Where would I look at on the ECM to see what number it has, and I don't have the ECM that went to the harness, but the truck was a 90' chevy 3500.
Forum: TBI
01-17-2014, 12:03 PM
Replies: 23
Views: 906
Posted By curtalert89

Re: Any ideas? 3.1 swap to 350tbi

So I'm guessing no one else knows either, ha!
Forum: TBI
01-16-2014, 08:56 PM
Replies: 23
Views: 906
Posted By curtalert89

Re: Any ideas? 3.1 swap to 350tbi

Thanks!
Forum: TBI
01-15-2014, 08:52 PM
Replies: 23
Views: 906
Posted By curtalert89

Any ideas? 3.1 swap to 350tbi

Okay first question, when I did my swap I used a truck harness from a 90' chevy truck, and I used a ECM that was given to me that came out of a 91 Camaro 305 tbi. Will they work together?

Now if...
Forum: TBI
01-15-2014, 08:07 PM
Replies: 0
Views: 331
Posted By curtalert89

Swapped my 3.1 for a 350 tbi

Okay first question, when I did my swap I used a truck harness from a 90' chevy truck, and I used a ECM that was given to me that came out of a 91 Camaro 305 tbi. Will they work together?

Now if...
Forum: TBI
01-14-2014, 09:38 PM
Replies: 0
Views: 294
Posted By curtalert89

Swapped my 3.1 v6 for a 350 tbi

Alright so I have no power going to my fuel pump, the injector pigtails, and the ALDL connector. I've checked the ECM and it's not getting any power to the wires that control each one (blue,green,...
Forum: TBI
01-14-2014, 03:13 PM
Replies: 1
Views: 346
Posted By curtalert89

Re: Wire harness ???

It won't let me upload the pics from my phone, so do you guys know what I'm talking about without a picture?
Forum: TBI
01-14-2014, 03:08 PM
Replies: 1
Views: 346
Posted By curtalert89

Wire harness ???

Okay so here's my problem, I just dropped in a 1990 tbi 350 into my 1991 v6 Camaro after the shitty v6 crapped out. So now the only hold up I have is the wire block on the driver side that bolts to...
Forum: Carburetors
01-14-2014, 01:02 PM
Replies: 0
Views: 416
Posted By curtalert89

Wiring up????

Okay so here's my problem, I just dropped in a 1990 tbi 350 into my 1991 v6 Camaro after the shitty v6 crapped out. So now the only hold up I have is the wire block on the driver side the bolts to...
Forum: Fabrication
12-21-2013, 12:25 PM
Replies: 72
Views: 13,754
Posted By curtalert89

Re: . . .Dash project. . .

Just wanted to see some finished product pics, if there is any.
Forum: Fabrication
12-18-2013, 08:19 PM
Replies: 72
Views: 13,754
Posted By curtalert89

Re: . . .Dash project. . .

Was this ever finished?
Forum: Brakes
12-03-2013, 05:40 PM
Replies: 22
Views: 32,995
Posted By curtalert89

Re: Disk brakes on any differential - DIY

So the same concept should work for my stock thirdgen rear end with fourth gen calipers and rotors with the mounts?
Forum: TBI
10-17-2013, 12:05 AM
Replies: 6
Views: 1,866
Posted By curtalert89

Re: 3.1 to 5.0 TBI Fuel Injection Swap

Okay, heres my question, I'm fixing to do a v6 (3.1) swap to a 350 Tbi v8 which came from an 89 truck. I have harness, computer, mounts ect. Even the tranny. Since my Camaro is a 91 and the speedo is...
Forum: Tech / General Engine
08-16-2013, 09:46 PM
Replies: 22
Views: 17,328
Posted By curtalert89

Re: 1991 camaro rs 3.1 v6 wont start just cranks

Okay so here's the run down on my problem. I have a 91 v6 and the original motor went to crap, ordered another from hawks thirdgen and did a complete swap. Started up first try. Drive it 15 miles...
Forum: Tech / General Engine
03-16-2013, 06:36 PM
Replies: 11
Views: 8,730
Posted By curtalert89

Re: speedo cable 88 camaro....HELP! lol

Checked it, it's still clipped in by the little lock piece
Forum: Tech / General Engine
03-16-2013, 05:25 PM
Replies: 11
Views: 8,730
Posted By curtalert89

Re: speedo cable 88 camaro....HELP! lol

Okay so my original speedo cable broke a couple months back, I replaces it yesterday with one from Autozone around 5pm, and I was driving to the local salvage yard to pick up a headliner for my car...
Forum: Electronics
01-28-2013, 08:18 PM
Replies: 5
Views: 1,301
Posted By curtalert89

Re: Aftermarket headlights ???

Awesome, thanks for the link!
Forum: Electronics
01-28-2013, 06:05 PM
Replies: 5
Views: 1,301
Posted By curtalert89

Re: Aftermarket headlights ???

It's there any way to fix that?
Forum: Electronics
01-28-2013, 06:03 PM
Replies: 15
Views: 12,601
Posted By curtalert89

Re: no power to ac compressor

Yes there is, I'm thinking it may be the relay, because I disconnected it and switches it with the other and when I do that my car won't start, but when I switch it back it starts up!
Forum: V6
01-21-2013, 01:13 PM
Replies: 7
Views: 2,273
Posted By curtalert89

Re: AC compressor inop

And do you know what the pressure is suppose to be for these
Forum: V6
01-21-2013, 11:41 AM
Replies: 7
Views: 2,273
Posted By curtalert89

Re: AC compressor inop

Awesome, thanks for the link, I checked the relay and switches them over, and I think it out because when I switch them around my car won't start, but when I switch them back it starts right up
Showing results 1 to 50 of 90
 
Page 1 of 2
1
2


 
Forum Jump


All times are GMT -5. The time now is 12:56 PM.