Looking at putting on a set of cobra wheels on
#1
Junior Member
Thread Starter
iTrader: (4)
Join Date: Oct 2006
Location: Indiana
Posts: 64
Likes: 0
Received 4 Likes
on
4 Posts
Car: 1991 Camaro Rs/Z28 clone
Engine: 5.3LSX
Transmission: T-56
Axle/Gears: DTS 12 Bolt 4.10
Looking at putting on a set of cobra wheels on
Now before anyone goes on a rant about the blasphemy of doing this, I already have my mind set on doing this if they'll fit. They are stock 96 cobra rims with 245s on the front and 275s on the rear. The adapter/spacer I'll need to make a ford bolt pattern is 1.25'' (31.75mm) thick. Cobra wheels have a +30mm offset with 5.72'' backspacing. So if I'm doing this right I'll be at a backspace of 4.47 inches with the adapter, with approximately a -1.75mm offset. From what I can see they would fit just fine, but I would appreciate a second opinion before I go spend the money on the spacers
#3
Supreme Member
iTrader: (14)
Join Date: Aug 2006
Location: Central NJ
Posts: 12,654
Likes: 0
Received 47 Likes
on
45 Posts
Car: 86 Trans Am, 92 Firebird
Engine: 408 sbc, 3.1L of raw power
Transmission: TKO600, T5
Axle/Gears: Moser 9", 3:70 trutac, 3:23 torsion
Re: Looking at putting on a set of cobra wheels on
Need to know the wheel widths before anybody can offer advice. That backspacing will fit the car, but without the width, I don't know if they will stick out. 4.5" of bs works with a 8 and maybe a 8.5 wheel, after that, its not enough
#4
Junior Member
Thread Starter
iTrader: (4)
Join Date: Oct 2006
Location: Indiana
Posts: 64
Likes: 0
Received 4 Likes
on
4 Posts
Car: 1991 Camaro Rs/Z28 clone
Engine: 5.3LSX
Transmission: T-56
Axle/Gears: DTS 12 Bolt 4.10
Re: Looking at putting on a set of cobra wheels on
Oh, forgot to mention, they are 17x8. If it does work, It'll be a few days before the spacers would arrive. I'll post some pics once mounted.
#6
Supreme Member
iTrader: (8)
Join Date: Oct 2001
Location: Il
Posts: 11,734
Received 795 Likes
on
528 Posts
Car: 1989-92 FORMULA350 305 92 Hawkclone
Engine: 4++,350 & 305 CIs
Transmission: 700R4 4800 vig 18th700R4 t56 ZF6 T5
Axle/Gears: 3.70 9"ford alum chunk,dana44,9bolt
Re: Looking at putting on a set of cobra wheels on
I wouldn't be mad about this if it was a good looking wheel but the 96 wheels are not good looking at all, even on a Stang.
Use a 17x9 95 cobra wheel with 275/40/17s all around and then you'll have something!
cool 95 wheels
not so cool 96 wheels
Use a 17x9 95 cobra wheel with 275/40/17s all around and then you'll have something!
cool 95 wheels
not so cool 96 wheels
Last edited by TTOP350; 06-12-2012 at 09:20 AM.
#7
Junior Member
Thread Starter
iTrader: (4)
Join Date: Oct 2006
Location: Indiana
Posts: 64
Likes: 0
Received 4 Likes
on
4 Posts
Car: 1991 Camaro Rs/Z28 clone
Engine: 5.3LSX
Transmission: T-56
Axle/Gears: DTS 12 Bolt 4.10
Re: Looking at putting on a set of cobra wheels on
To each their own, but I personally like the stock cobra rims, and they'll look a heck of a lot better than my old beat up stock wheels. I do have a set of cobra r replicas, but they're on my 94 gt. they would be way to big to fit on my camaro
Trending Topics
#8
Supreme Member
iTrader: (8)
Join Date: Oct 2001
Location: Il
Posts: 11,734
Received 795 Likes
on
528 Posts
Car: 1989-92 FORMULA350 305 92 Hawkclone
Engine: 4++,350 & 305 CIs
Transmission: 700R4 4800 vig 18th700R4 t56 ZF6 T5
Axle/Gears: 3.70 9"ford alum chunk,dana44,9bolt
Re: Looking at putting on a set of cobra wheels on
Why do you think the "R" wheels are to big? they are 17x9 or 9.5 right?? We put them on my friends 86 GT with 275/40/17s all around.
I have 17x9.5 96 WS6 wheels on my 89 formula 350 with a 275/40/17 tire on all 4 corners...
I have 17x9.5 96 WS6 wheels on my 89 formula 350 with a 275/40/17 tire on all 4 corners...
#9
Re: Looking at putting on a set of cobra wheels on
The stock cobra wheels are hideous! The cobra r wheels with some 275 tires would look perfectly on a 3rd gen. (Minus the cobra center cap)
#10
Junior Member
Thread Starter
iTrader: (4)
Join Date: Oct 2006
Location: Indiana
Posts: 64
Likes: 0
Received 4 Likes
on
4 Posts
Car: 1991 Camaro Rs/Z28 clone
Engine: 5.3LSX
Transmission: T-56
Axle/Gears: DTS 12 Bolt 4.10
Re: Looking at putting on a set of cobra wheels on
Cobra r's on my gt are 17x9 and 17x10.5. 275s on the front and 285s on the rear. I was using a 315 on the rear but they were causing some issues so I stepped down. With the ford offset, I'm pretty sure I couldnt get wider than an 8.5" ford rim on my camaro.
#11
Supreme Member
iTrader: (8)
Join Date: Oct 2001
Location: Il
Posts: 11,734
Received 795 Likes
on
528 Posts
Car: 1989-92 FORMULA350 305 92 Hawkclone
Engine: 4++,350 & 305 CIs
Transmission: 700R4 4800 vig 18th700R4 t56 ZF6 T5
Axle/Gears: 3.70 9"ford alum chunk,dana44,9bolt
Re: Looking at putting on a set of cobra wheels on
I thought they were close? your going to need a spacer most likely anyway.
Im sure if I looked I could find the info..
#12
Junior Member
Thread Starter
iTrader: (4)
Join Date: Oct 2006
Location: Indiana
Posts: 64
Likes: 0
Received 4 Likes
on
4 Posts
Car: 1991 Camaro Rs/Z28 clone
Engine: 5.3LSX
Transmission: T-56
Axle/Gears: DTS 12 Bolt 4.10
Re: Looking at putting on a set of cobra wheels on
I'm assuming they are the same as the cobra wheels, not so much that is a problem, it's more that I haven't seen an adapter wider than 1.25''. No way I could put them on with that adapter.
#13
Junior Member
Thread Starter
iTrader: (4)
Join Date: Oct 2006
Location: Indiana
Posts: 64
Likes: 0
Received 4 Likes
on
4 Posts
Car: 1991 Camaro Rs/Z28 clone
Engine: 5.3LSX
Transmission: T-56
Axle/Gears: DTS 12 Bolt 4.10
Re: Looking at putting on a set of cobra wheels on
To each their own, I personally like them, and it's a nice changed from your everyday corvette/4th gen wheel that most 3rd gens run
#14
Supreme Member
iTrader: (5)
Join Date: Jan 2008
Location: Paradise, Hawaii
Posts: 1,127
Likes: 0
Received 1 Like
on
1 Post
Car: Too many cars
Re: Looking at putting on a set of cobra wheels on
Im running 2" & 2.25" adapters on my camaros ZR1 rims & they are GS offsets. I got a deal on some Black Bullit rims 17x8.5 & 17x10.5 ford bolt pattern. Gonna use 2" ford to chevy adapters.
#16
Junior Member
Thread Starter
iTrader: (4)
Join Date: Oct 2006
Location: Indiana
Posts: 64
Likes: 0
Received 4 Likes
on
4 Posts
Car: 1991 Camaro Rs/Z28 clone
Engine: 5.3LSX
Transmission: T-56
Axle/Gears: DTS 12 Bolt 4.10
Re: Looking at putting on a set of cobra wheels on
Nice, If you don't mind, where did you find 2'' adapters, I've only found the 1.25'' ones
#17
Supreme Member
iTrader: (8)
Join Date: Oct 2001
Location: Il
Posts: 11,734
Received 795 Likes
on
528 Posts
Car: 1989-92 FORMULA350 305 92 Hawkclone
Engine: 4++,350 & 305 CIs
Transmission: 700R4 4800 vig 18th700R4 t56 ZF6 T5
Axle/Gears: 3.70 9"ford alum chunk,dana44,9bolt
Re: Looking at putting on a set of cobra wheels on
Google is your friend
http://www.google.com/search?q=wheel...w=1441&bih=686
http://www.google.com/search?q=wheel...w=1441&bih=686
#18
Supreme Member
Join Date: Apr 2012
Location: Streetsboro Oh
Posts: 1,353
Likes: 0
Received 1 Like
on
1 Post
Car: 1987 T/A WS6 T-Tops/92 RS
Engine: LB9/3.1
Transmission: 700R4/700R4
Axle/Gears: 2.73/3.23
Re: Looking at putting on a set of cobra wheels on
Yeah IMO the 96 Cobra wheels are not very good looking. I had a set of the silver 99 Cobra wheels on my slammed 95 stang and it looked killer.
#20
Supreme Member
iTrader: (1)
Join Date: Jun 2001
Location: Tacoma, Wa
Posts: 3,109
Likes: 0
Received 25 Likes
on
17 Posts
Car: '91 TA vert
Engine: turboLSx
Transmission: T56
Axle/Gears: 3.23
Re: Looking at putting on a set of cobra wheels on
I've always thought those were a marginally cool wheel at best. But since they now offer them for every make of car out there, and it's common place, they've lost their sliver of appeal. I think I've seen them (in person, not just on the interwebs) on everything from focus', taurus', s10s, civics, to even a bmw. It's like the 2000's version of the torque thrust.
#21
Junior Member
Thread Starter
iTrader: (4)
Join Date: Oct 2006
Location: Indiana
Posts: 64
Likes: 0
Received 4 Likes
on
4 Posts
Car: 1991 Camaro Rs/Z28 clone
Engine: 5.3LSX
Transmission: T-56
Axle/Gears: DTS 12 Bolt 4.10
Re: Looking at putting on a set of cobra wheels on
Got the spacers today and mounted the wheels on, I personally think they look pretty sharp now that they are actually on the car, no fitment issues whatsoever. I'll post pics once I get a chance to take some, have to go to work shortly so no time now
#22
Supreme Member
iTrader: (8)
Join Date: Oct 2001
Location: Il
Posts: 11,734
Received 795 Likes
on
528 Posts
Car: 1989-92 FORMULA350 305 92 Hawkclone
Engine: 4++,350 & 305 CIs
Transmission: 700R4 4800 vig 18th700R4 t56 ZF6 T5
Axle/Gears: 3.70 9"ford alum chunk,dana44,9bolt
Re: Looking at putting on a set of cobra wheels on
Yeah, get some pix up asap.. would like to see em..
Thread
Thread Starter
Forum
Replies
Last Post
colton_carlson
Firebirds for Sale
7
03-08-2019 12:21 PM
kah992
Engine/Drivetrain/Suspension Parts for Sale
2
08-19-2015 02:55 PM