Any 8.5" rearends for Third Gens?
#1
Any 8.5" rearends for Third Gens?
I ask if there is a 8.5 that is close to fitting the third gens. I have seen a 8.5 with PBR aluminum calipers that was supposed to be in a 91 1LE camaro. I know it wasnt stock because it has upper ears like a Grand National. Any ideas?
#2
Supreme Member
iTrader: (14)
Join Date: Aug 2006
Location: Central NJ
Posts: 12,651
Likes: 0
Received 46 Likes
on
44 Posts
Car: 86 Trans Am, 92 Firebird
Engine: 408 sbc, 3.1L of raw power
Transmission: TKO600, T5
Axle/Gears: Moser 9", 3:70 trutac, 3:23 torsion
Re: Any 8.5" rearends for Third Gens?
if it had the upper ears, then no it was never in the 91 camaro, unless sombody went through all the hassle of rebuilding the rear frame for use with the triangulated 4 link from the GN
as for 8.5's, thats a 12bolt, and you cen get aftermarket 12 bolts form moser or strange engineering that will bolt right in. looking at a min of 2k though. Unless you can find a used one.
as for 8.5's, thats a 12bolt, and you cen get aftermarket 12 bolts form moser or strange engineering that will bolt right in. looking at a min of 2k though. Unless you can find a used one.
#3
Re: Any 8.5" rearends for Third Gens?
8.5"s are 10 bolts. Search Grand National and Second Gen Camaro rear ends.
I know its not stock.
http://i47.photobucket.com/albums/f1...7/Fullshot.jpg
http://i47.photobucket.com/albums/f1...n007/Cover.jpg
http://i47.photobucket.com/albums/f1...ren007/PBR.jpg
I know its not stock.
http://i47.photobucket.com/albums/f1...7/Fullshot.jpg
http://i47.photobucket.com/albums/f1...n007/Cover.jpg
http://i47.photobucket.com/albums/f1...ren007/PBR.jpg
Last edited by gwarren007; 07-03-2010 at 03:45 PM.
#4
Supreme Member
iTrader: (14)
Join Date: Aug 2006
Location: Central NJ
Posts: 12,651
Likes: 0
Received 46 Likes
on
44 Posts
Car: 86 Trans Am, 92 Firebird
Engine: 408 sbc, 3.1L of raw power
Transmission: TKO600, T5
Axle/Gears: Moser 9", 3:70 trutac, 3:23 torsion
Re: Any 8.5" rearends for Third Gens?
8.5"s are 10 bolts. Search Grand National and Second Gen Camaro rear ends.
I know its not stock.
http://i47.photobucket.com/albums/f1...7/Fullshot.jpg
http://i47.photobucket.com/albums/f1...n007/Cover.jpg
http://i47.photobucket.com/albums/f1...ren007/PBR.jpg
I know its not stock.
http://i47.photobucket.com/albums/f1...7/Fullshot.jpg
http://i47.photobucket.com/albums/f1...n007/Cover.jpg
http://i47.photobucket.com/albums/f1...ren007/PBR.jpg
that rear pictured is not for and 3rd gen and was never in one. move on.
#6
Re: Any 8.5" rearends for Third Gens?
The only rear ends that were built to fit the 3rd gen were the 7.5, 9 bolt and a few Dana 44s. There are after market 12 bolt and 9 inch Fords. No 8.5 corporate rear ends were ever built for the 3rd gen.
#7
Supreme Member
iTrader: (2)
Re: Any 8.5" rearends for Third Gens?
dana 44 was the only (sorta) stock 8.5" ring gear rear end for 3rd gen f-bodies, period. sold by gmpp and found in fire-hawks they are few and far between.
if you really want one for a "it was stock" reason pm me, otherwise get a 12bolt (8.75" ring gear) and call it done
if you really want one for a "it was stock" reason pm me, otherwise get a 12bolt (8.75" ring gear) and call it done
Trending Topics
#9
Re: Any 8.5" rearends for Third Gens?
I would say that the Impala, Caprice rear end would be closest to the right width for the 3rd gen. Maybe a '73 to '77 Monte Carlo or similar car.
#10
TGO Supporter
Join Date: Oct 2002
Location: Saskatoon, SK, Canada
Posts: 9,067
Likes: 0
Received 1 Like
on
1 Post
Car: '83 Z28, '07 Charger SRT8
Engine: 454ci, 6.1 Hemi
Transmission: TH350, A5
Axle/Gears: 2.73 posi, 3.06 posi
Re: Any 8.5" rearends for Third Gens?
2ndgen F-body used an 8.5" from '71-81 thats almost exactly the right width for a 3rdgen. IIRC, measured end to end, the 2ndgen 8.5" housing is less than an inch shorter than the 3rgen 7.5" housing.
Thread
Thread Starter
Forum
Replies
Last Post
Hotrodboba400
Firebirds for Sale
3
12-10-2019 07:07 PM
New2Chevy
Engine/Drivetrain/Suspension Parts for Sale
2
09-28-2015 12:35 AM