cylinder select error
07-26-2009, 11:28 AM
#1
Member
Thread Starter
iTrader: (5)
Join Date: Apr 2005
Location: chicago, IL
Posts: 353
Likes: 0
Received 0 Likes
on
0 Posts
Car: 89 Iroc-z
Engine: 5.7 lt
Transmission: 700r4
Axle/Gears: 9 bolt
cylinder select error
i am having a guy tune my ECM and it keeps coming up with a cylinder select error. is that an error on his side or is that an error with a sensor or something along that line with the car.
07-26-2009, 12:56 PM
#2
Supreme Member
iTrader: (1)
Join Date: Apr 2004
Location: Browns Town
Posts: 3,178
Likes: 0
Received 3 Likes
on
3 Posts
Car: 86 Monte SS (730,$8D,G3,AP,4K,S_V4)
Engine: 406 Hyd Roller 236/242
Transmission: 700R4 HomeBrew, 2.4K stall
Axle/Gears: 3:73 Posi, 7.5 Soon to break
Re: cylinder select error
Memcal is probably wrong for the application
07-26-2009, 10:36 PM
#4
Supreme Member
iTrader: (1)
Join Date: Apr 2004
Location: Browns Town
Posts: 3,178
Likes: 0
Received 3 Likes
on
3 Posts
Car: 86 Monte SS (730,$8D,G3,AP,4K,S_V4)
Engine: 406 Hyd Roller 236/242
Transmission: 700R4 HomeBrew, 2.4K stall
Axle/Gears: 3:73 Posi, 7.5 Soon to break
Re: cylinder select error
https://www.thirdgen.org/forums/dfi-...om-calpak.html
This is a sticky in the DFI & ECM board.
there is a resistor(s) that indicate if the Memcal is for a V6 or V8.
Cylinder select error indicates the software is stating one thing and the hardware is for another.
there are ways around this if needed. Search memcal in the DIY-Prom board.
This is a sticky in the DFI & ECM board.
there is a resistor(s) that indicate if the Memcal is for a V6 or V8.
Cylinder select error indicates the software is stating one thing and the hardware is for another.
there are ways around this if needed. Search memcal in the DIY-Prom board.
07-28-2009, 11:06 PM
#5
Member
Thread Starter
iTrader: (5)
Join Date: Apr 2005
Location: chicago, IL
Posts: 353
Likes: 0
Received 0 Likes
on
0 Posts
Car: 89 Iroc-z
Engine: 5.7 lt
Transmission: 700r4
Axle/Gears: 9 bolt
Re: cylinder select error
ok i get this now the ecm is the stock 350 ecm that GM installed in the car. the guy that is tuning the car said he changed the cylinder select to 8 in the computer what should it be set at 0?
07-29-2009, 06:14 PM
#6
Supreme Member
iTrader: (1)
Join Date: Apr 2004
Location: Browns Town
Posts: 3,178
Likes: 0
Received 3 Likes
on
3 Posts
Car: 86 Monte SS (730,$8D,G3,AP,4K,S_V4)
Engine: 406 Hyd Roller 236/242
Transmission: 700R4 HomeBrew, 2.4K stall
Axle/Gears: 3:73 Posi, 7.5 Soon to break
Re: cylinder select error
Yes, It should be 00 for 8 cylinders in that application.
If you still get that error, The memcal is from a V6 or other.
If you still get that error, The memcal is from a V6 or other.
Thread
Thread Starter
Forum
Replies
Last Post
