Repinning TBI to Speed Density TPI
#352
Junior Member
Join Date: Dec 2020
Location: Colorado Springs, Colorado
Posts: 14
Likes: 0
Received 0 Likes
on
0 Posts
Car: 91 camaro rs
Engine: 350 Police tbi
Transmission: 700r4
Axle/Gears: 12 bolt 373 posi
Re: Repinning TBI to Speed Density TPI
Is this the pin out ? I have a 8746.
#354
Member
Join Date: May 2000
Location: Chilliwack, BC
Posts: 415
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1992 Camaro RS
Engine: 5.7 V8 TPI
Transmission: T-5 5-Speed Manual
Re: Repinning TBI to Speed Density TPI
I’ve just completed the repining of the TBI harness on my ‘92 RS and almost everything seems to be good. The one issue I have, is that the SES light is on and jumpering the a/b pins on the ALDL does nothing. No code 12 and no other codes, just a steady glow of the SES light.
any ideas?
any ideas?
#356
Member
Join Date: May 2000
Location: Chilliwack, BC
Posts: 415
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1992 Camaro RS
Engine: 5.7 V8 TPI
Transmission: T-5 5-Speed Manual
#357
Member
Join Date: Jan 2013
Location: minnesota
Posts: 115
Received 0 Likes
on
0 Posts
Car: 89 Firebird
Engine: 5.7
Transmission: 700r4
Axle/Gears: unkown
Re: Repinning TBI to Speed Density TPI
Step 4: 1227730 conversion
Splice the right bank injector wires to 4 injector plugs. All the grounds go together to one wire, all the positives go together to the other wire. Now, splice the left bank in place to the left 4 injector plugs. If using TPI plugs, the green plugs go on right side, the red plugs go on left side.
Remove the ESC module. Cut the connector off, and splice wires C and E together. Tape up, and hide someplace neat.
Connect MAT, TPS, CTS, and IAC. Extend wires if needed.
Step 5: Repin
Now, repin ECM connector using following table:
Step 6: Calibration changes
At minimum, you will need to change the VSS constant from "magnetic" to "optical" because the 4-out buffer box outputs 2k pulses per mile, vs the 4k pulses per mile that the $8D calibration expects.
You may need to disable VATS, EGR, etc depending on how you did your swap.
Splice the right bank injector wires to 4 injector plugs. All the grounds go together to one wire, all the positives go together to the other wire. Now, splice the left bank in place to the left 4 injector plugs. If using TPI plugs, the green plugs go on right side, the red plugs go on left side.
Remove the ESC module. Cut the connector off, and splice wires C and E together. Tape up, and hide someplace neat.
Connect MAT, TPS, CTS, and IAC. Extend wires if needed.
Step 5: Repin
Now, repin ECM connector using following table:
Step 6: Calibration changes
At minimum, you will need to change the VSS constant from "magnetic" to "optical" because the 4-out buffer box outputs 2k pulses per mile, vs the 4k pulses per mile that the $8D calibration expects.
You may need to disable VATS, EGR, etc depending on how you did your swap.
#360
Junior Member
Join Date: Feb 2019
Location: Deer Lodge, TN
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
Car: '91 S-10 & '27 T coupe
Engine: 350
Transmission: 700r4
Re: Repinning TBI to Speed Density TPI
I would like to know if this pinning order, is the same for going from a 8062 ecu wiring, to a 7730 ecu.
I am installing TPI 350, speed density into my '91 TBI S-10. I had the chip burned for the 7730. Now I just need to find out what the re-pinning order is for it. Mine has 3 plug-ins on it. The 2 black side plugs, plug right in, but the 3rd is totally different.
Thanks, Pat
I am installing TPI 350, speed density into my '91 TBI S-10. I had the chip burned for the 7730. Now I just need to find out what the re-pinning order is for it. Mine has 3 plug-ins on it. The 2 black side plugs, plug right in, but the 3rd is totally different.
Thanks, Pat
#362
Junior Member
Join Date: Feb 2019
Location: Deer Lodge, TN
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
Car: '91 S-10 & '27 T coupe
Engine: 350
Transmission: 700r4
Re: Repinning TBI to Speed Density TPI
I've registered a couple of days ago, there, but they still won't let me read/see what you posted.
#364
Junior Member
Join Date: Feb 2019
Location: Deer Lodge, TN
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
Car: '91 S-10 & '27 T coupe
Engine: 350
Transmission: 700r4
Re: Repinning TBI to Speed Density TPI
Still won't let me look at them yet this morning! They Need to wake up over there. This wait is ridicules!
#365
TGO Supporter/Moderator
Thread Starter
iTrader: (12)
Join Date: Jul 1999
Location: SALEM, NH
Posts: 11,732
Likes: 0
Received 89 Likes
on
75 Posts
Car: '88 Formula, '94 Corvette, '95 Bird
Engine: LC9, 355" LT1, LT1
Transmission: T5, Zf6, 4L60E
Axle/Gears: 3.42, Dana44 3.45, 3.23
Re: Repinning TBI to Speed Density TPI
Crazy.. I started this thread 20 years ago. People are still repining these and using factory ECMs.
#366
Member
Join Date: Sep 2002
Location: honolulu
Posts: 185
Likes: 0
Received 10 Likes
on
10 Posts
Car: '86MCSS
Engine: 396 .030"
Transmission: M20
Re: Repinning TBI to Speed Density TPI
I have no problem seeing any of the attached items in your thread that you started over there. You need to be logged in to that site to see or download any of the attachments there. ...or maybe you're clicking on the actual picture of theattached xls/pdf, try clicking on the number/words of the posted file.
Thread
Thread Starter
Forum
Replies
Last Post