lost my keys
12-05-2009, 11:31 AM
#1
Senior Member
Thread Starter
Join Date: Jul 2007
Location: Manteca, Ca
Posts: 582
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1983, 1986, 2001 Trans Am
Engine: 305 cfi, 350 carb, LS1
Transmission: 700,Edge 2800 th350,Edge 3400 4L60E
Axle/Gears: 9 Bolt 3.27 Borg-Warner, built 3.73
lost my keys
got a new ignition cylinder and i cant get the lock plate off any help
12-05-2009, 12:26 PM
#2
Supreme Member
iTrader: (16)
Join Date: Jun 2002
Location: Vancouver, WA
Posts: 1,296
Likes: 0
Received 4 Likes
on
3 Posts
Car: 87 IROC-Z28
Engine: 305 TPI-New 355 on the engine stand
Transmission: T56
Axle/Gears: 3.73 Eaton posi-Soon a 9" Ford!
Re: lost my keys
Auto parts stores rent lock plate removal tools. Usually you pay a deposit and then when you bring it back you get all your money back. Autozone, Schucks, oreilly's have them for rent. I use one so much I bought one to take with me to the wrecking yards.
Last edited by alloy; 12-05-2009 at 12:34 PM. Reason: added pic
12-05-2009, 01:23 PM
#3
Senior Member
iTrader: (2)
Join Date: Aug 2006
Location: LONG ISLAND, NY
Posts: 548
Likes: 0
Received 11 Likes
on
10 Posts
Car: 1991 camaro rs convertible
Engine: Built ls1
Transmission: T56
Axle/Gears: 3:42
Re: lost my keys
Yep you are going to need that tool to take the plate off and put it back on. They are pretty cheap actually, I just bought one to save the trouble of renting it.
12-07-2009, 04:47 PM
#4
Re: lost my keys
If you dont want to buy the tool you can build your own.. I did it, I will quote my post from another thread intead of writing a new one
So thats another way to go if you dont want to buy the tools, cheap and worked the same way
QUOTED Thread: https://www.thirdgen.org/forums/tech...placement.html
You need an Steering Wheel puller and a Lock Plate Depressor,
Star by removing the bolts and horn button.
Steering wheel removed, and the Lock Plate is showing
I built my own Lock Plate Depressor, as shown below:
Remove the locker ring
Lockplate gone. Remove all loose things, and photo to remember how it was assebled
The black bolt is for removing the ignition lock cylinder
You dont have vats so you wouldnt have the wire into the lock cylinder, Just turn the lock cylinder clockwise (i think it was) and remove it, install the newone turning it counterclock wise and insert bolt and then check to see if it turns ok.. if it does assemble everything, if not, adjust the lock cylinder.
You got more pictures from my change of the ignition lock cylinder : http://theking.joakimweb.se/z28/proj...nitionlock.htm
Its in swedish but you see the pictures, hope this post help you out.
Star by removing the bolts and horn button.
Steering wheel removed, and the Lock Plate is showing
I built my own Lock Plate Depressor, as shown below:
Remove the locker ring
Lockplate gone. Remove all loose things, and photo to remember how it was assebled
The black bolt is for removing the ignition lock cylinder
You dont have vats so you wouldnt have the wire into the lock cylinder, Just turn the lock cylinder clockwise (i think it was) and remove it, install the newone turning it counterclock wise and insert bolt and then check to see if it turns ok.. if it does assemble everything, if not, adjust the lock cylinder.
You got more pictures from my change of the ignition lock cylinder : http://theking.joakimweb.se/z28/proj...nitionlock.htm
Its in swedish but you see the pictures, hope this post help you out.
QUOTED Thread: https://www.thirdgen.org/forums/tech...placement.html
Thread
Thread Starter
Forum
Replies
Last Post
Gunner242
Electronics
7
12-25-2015 04:49 PM
Linson
Auto Detailing and Appearance
12
10-01-2015 09:50 PM
3.8TransAM
NW Indiana and South Chicago Suburb
1
09-27-2015 08:37 PM
