how to install a B&M console ratchet shifter
#2
TGO Supporter
iTrader: (2)
Open the box and read the instructions?
------------------
The IROC Homepage
<A HREF="http://www.rit.edu/~jli4307/camaro" TARGET=_blank>
View the restoration of an 85 IROC</A>
"I didn't know a bored out Ford could go so slow" -Shenandoah
------------------
The IROC Homepage
<A HREF="http://www.rit.edu/~jli4307/camaro" TARGET=_blank>
View the restoration of an 85 IROC</A>
"I didn't know a bored out Ford could go so slow" -Shenandoah
#3
------------------
92 Z28 L98 350
---------------
Ported and polished heads, ported stock TPI base, ported plenum, Comp Cams XR270HR-10 cam (lift .495/.502 duration 218/224 lobe separation 110), Edelbrock TES headers, LT4 valve springs, Crane AFPR, Flowmaster catback with LT1 style tips, MSD coil & wires...
"Take that auto, drop it in first, hold the brakes, stomp the gas and grin from ear to ear! :-)
#4
i have the b and m console shifter in my 88 formula and i love it just took pics of it should be back soon. it wasnt that hard to do actually. i did have to take the saw zall to the console plate but other than that it went pretty smooth other then the relay that i had to put in but if u have any other questions let me know at stahlja@hotmail.com ok..
------------------
1988 firebird formula350tpi msd 6al box blaster 3 coil accel 8.8 wires flowmaster cat back pro shift light a pillar gauge pod and water temp and air/fuel ratio gauges b&m mega console shifter
------------------
1988 firebird formula350tpi msd 6al box blaster 3 coil accel 8.8 wires flowmaster cat back pro shift light a pillar gauge pod and water temp and air/fuel ratio gauges b&m mega console shifter
#5
i just put mine in! its very nice i even added a 8 ball to top it off. you will { on mine that is} cut out that little bar thats in the counsel and drill 2 new holes at the top of the shifter. then you can mount it in. then the electrical is easy. the cable is a sinch. and you wont use one of them cause there are 2 in there. good luck. the best part is that you cant miss a shift from 1 2 3 then it goes into nuetral but you cant hit it in to reverse. you have to put it back in drive and lift up the handle in order to go into reverse or park. if ya got any more questions let me know later.
------------------
84 camaro 350sb 750 carb edelbrock intake 1.6 roller rockers manley severe duty valves crane fireball cam holley high volume fuel pump hp pistons stock crank mellings high volume oil pump edelbrock tes headers flowmaster 3 inch exhaust turbo 350 tranny rebuilt w/shift kit b&m deep aluminum pan msd ignition b&m rachet shifter lakewood lowercontrol arms polyurethane tranny mount {red}richmonds 4:10 gears with minispool.
------------------
84 camaro 350sb 750 carb edelbrock intake 1.6 roller rockers manley severe duty valves crane fireball cam holley high volume fuel pump hp pistons stock crank mellings high volume oil pump edelbrock tes headers flowmaster 3 inch exhaust turbo 350 tranny rebuilt w/shift kit b&m deep aluminum pan msd ignition b&m rachet shifter lakewood lowercontrol arms polyurethane tranny mount {red}richmonds 4:10 gears with minispool.
#6
Junior Member
Join Date: Dec 2007
Location: Las Vegas NV
Posts: 2
Likes: 0
Received 0 Likes
on
0 Posts
Car: 85 Camaro Z28
Engine: 305
Re: how to install a B&M console ratchet shifter
I am trying to install the Quicksilver Shifter on my car and I can not figure out which wires go where. There are four slots on the sensors but there are 6 wires on the harness. can some one help me?
#7
Junior Member
Join Date: Sep 2011
Location: Vancouver, BC
Posts: 21
Likes: 0
Received 0 Likes
on
0 Posts
Car: 89 firebird
Engine: 2.8 soon to be built 3.4
Transmission: 700r4
Axle/Gears: 4th gen posi
Re: how to install a B&M console ratchet shifter
does anyone have pics of this shifter installed?
Trending Topics
#8
Junior Member
Join Date: Sep 2012
Location: Niagara Falls, Ontario, Canada
Posts: 9
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1987 Pontiac Firebird
Engine: 5.7L T.P.I.
Re: how to install a B&M console ratchet shifter
I have installed the b&m console megashfter on my 87 Firebird. Where do u mount the new light for the gear selector?
Thread
Thread Starter
Forum
Replies
Last Post
1992 Trans Am
History / Originality
27
05-10-2023 07:19 PM
1985, 350, aluminum, bm, camaro, console, forum, install, installation, installing, pan, quicksilver, ratchet, shifter, turbo