would it be worth it???? need quick answer
#1
Member
Thread Starter
Join Date: Dec 2006
Posts: 224
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 camaro z28
Engine: 350sbc
Transmission: TKO 600
Axle/Gears: stock axle with 4.11's
would it be worth it???? need quick answer
not sure where to post this...i have 84 z28 frame bent found a rs v6 camaro guy parting out body and frame in perfect shape...would it be worth it to convert everything over to the v6 one? motor trans...interior...rear end...driveshaft...suspension...my spoiler and change all the emblems to z28...or would it be better to take what i need from it and just get my frame fix and get all the body work fixed...???? need quick answer on this thx....mod if you want to move this into section you think is better plz do
#2
Supreme Member
iTrader: (3)
Join Date: May 2008
Location: boise, ID
Posts: 1,116
Likes: 0
Received 1 Like
on
1 Post
Car: 91 B4C "police special service"
Engine: L98 494hp
Transmission: tko-600 on order
Axle/Gears: 3.23 true trac
Re: would it be worth it???? need quick answer
depends on the amount of damage done to car....are you talking just front sub-frame damaged??
#3
Member
Thread Starter
Join Date: Dec 2006
Posts: 224
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 camaro z28
Engine: 350sbc
Transmission: TKO 600
Axle/Gears: stock axle with 4.11's
Re: would it be worth it???? need quick answer
on my car the frame is bent front pass wheel pushed back 2 inch and in about inch still drives just pulls to right a bit...and it has some dmg to pass quater panel...this is my current car one im going to look at has no body dmg...its a v6 though and paint is good and rims and tires good...just wanting to know if it be worth it or not
#4
Supreme Member
iTrader: (2)
Join Date: Mar 2005
Location: East Tennesse
Posts: 2,820
Likes: 0
Received 3 Likes
on
3 Posts
Car: 1991 RS Camaro
Engine: L03 (want LS1)
Transmission: 700R-4 (and T56)
Axle/Gears: 4th Gen 3.23 posi
Re: would it be worth it???? need quick answer
well, if your's is damaged and V6 car is not, and you have the mechanical know-how, I'd get the V6 car and swap all your car's stuff into the V6 shell
#5
Member
Thread Starter
Join Date: Dec 2006
Posts: 224
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 camaro z28
Engine: 350sbc
Transmission: TKO 600
Axle/Gears: stock axle with 4.11's
Re: would it be worth it???? need quick answer
yeah i got the know how...well ima go take a look tomarrow...if i dont get it i might just get a few parts off of it...anyways thx for advice
#6
Member
Thread Starter
Join Date: Dec 2006
Posts: 224
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 camaro z28
Engine: 350sbc
Transmission: TKO 600
Axle/Gears: stock axle with 4.11's
Re: would it be worth it???? need quick answer
ok well the guy lied about the car...he said it had no body dmg or scratches in paint...clear coat was peeling off back bumper had a huge dent in pass front bumper and the hole front end of car has been replaced and wasnt even painted it was primer grey and was being hidden under a nose bra...guy wasnt even there when i showed up even though he was oppose to be finally he calls me back and says he will be there in two hours...i said forget it not interested and hoped back in truck and drove 2 hours back home...so it was like a total of 4 hours of driving there and back...big waste of my time...bummer too i was excited about it...
Thread
Thread Starter
Forum
Replies
Last Post
[Sold] Quick fuel 750 cfm
mackjar66
Engine/Drivetrain/Suspension Parts for Sale
0
09-14-2015 01:17 PM