Dyno Day 2 (The Sequel)
#51
Member
Join Date: Mar 2008
Location: Lakewood, California
Posts: 375
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1992 Camaro RS 25th Anniversary
Engine: Stock 305 TBI, LT1 soon.
Transmission: V6 NWC T5 by choice
Axle/Gears: Zexel Torsen LSD with 3.23's
Re: Dyno Day 2 (The Sequel)
Ok, so showing up to spectate is ok too? I really just interested in talking to all of you guys and picking your brains lol.
#52
Supreme Member
Thread Starter
iTrader: (1)
Join Date: Jul 2000
Location: Carson, CA
Posts: 1,290
Likes: 0
Received 0 Likes
on
0 Posts
Car: '88 GTA, 90 Formula
Engine: 5.7 TPI, fed growth hormones
Transmission: 700r4 4u2?
Axle/Gears: 9bolt
Re: Dyno Day 2 (The Sequel)
OK, trying to figure out a count! We can't do more than 7, six is actually plenty. The cars will go on in the order that you signed up. Please check your timing and fuel pressure (spout connector disconnected to check timing) so we don't waste dyno time doing that. If you need help with that, let us know before the car is on the dyno, and someone will help you. You are welcome to come and watch/spy/learn, and trust me, you will learn.
1. Troy (TA)
2. Lon (lonsal)
3. Burnout91 (Bill)
4. Luis (Godreject)
5. Julie (JulieGTA)
6. Mike (itsMikey)
7. if time allows
TA
1. Troy (TA)
2. Lon (lonsal)
3. Burnout91 (Bill)
4. Luis (Godreject)
5. Julie (JulieGTA)
6. Mike (itsMikey)
7. if time allows
TA
#53
Member
Join Date: Mar 2008
Location: Lakewood, California
Posts: 375
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1992 Camaro RS 25th Anniversary
Engine: Stock 305 TBI, LT1 soon.
Transmission: V6 NWC T5 by choice
Axle/Gears: Zexel Torsen LSD with 3.23's
Re: Dyno Day 2 (The Sequel)
I'll definitely be there to watch and learn then. Look out for a completely black RS.
#55
Senior Member
iTrader: (1)
Join Date: May 2007
Location: CPT (Southern Cali)
Posts: 754
Likes: 0
Received 0 Likes
on
0 Posts
Car: 09 GSXR/88 iroc/91 RS B4C
Engine: 600cc/l5.7/5.7
Transmission: 6 speed/TH 350/auto
Axle/Gears: 45tooth rear?/3.23/3.42
Re: Dyno Day 2 (The Sequel)
I will have to withdrawl my name from the list, my car is not any different then last dyno(besides new exhaust) and i did not do some changes i needed to make, i will attend though and spy, i hope to be ready for the next session though
#56
Supreme Member
iTrader: (4)
Join Date: Nov 2003
Location: santa barbara,ca
Posts: 1,194
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1990 iroc z
Engine: LSX 376 F1A
Transmission: 4l60e
Axle/Gears: 12 bolt 3.42
Re: Dyno Day 2 (The Sequel)
We'll I am still planning to be there tomorrow so I hope there Is still a spot in for me. My car needs tuning bad..
#57
Supreme Member
Join Date: Apr 2009
Location: Scottsdale, AZ
Posts: 2,852
Likes: 0
Received 1 Like
on
1 Post
Car: 89 GTA/93 S13/91 Si
Engine: 5.7 350 TPI
Transmission: 700R4
Axle/Gears: 3.23
Re: Dyno Day 2 (The Sequel)
still planning on coming...me,dad(wicketmike) and my girlfreind..tryin to get her into the thirdgen scene too
#58
Supreme Member
Thread Starter
iTrader: (1)
Join Date: Jul 2000
Location: Carson, CA
Posts: 1,290
Likes: 0
Received 0 Likes
on
0 Posts
Car: '88 GTA, 90 Formula
Engine: 5.7 TPI, fed growth hormones
Transmission: 700r4 4u2?
Axle/Gears: 9bolt
Re: Dyno Day 2 (The Sequel)
Everyone is welcome to come and watch. Don did not sign on to test, I don't think his exhaust mods are ready yet, and this looks like a pretty full day already, so we'll definately be going again pretty soon.
1. Troy (TA)
2. Lon (lonsal)
3. Burnout91 (Bill)
4. Julie (JulieGTA)
5. Mike (itsMikey)
6. 90-irocdx3 (Name?)
7. if time allows
TA
1. Troy (TA)
2. Lon (lonsal)
3. Burnout91 (Bill)
4. Julie (JulieGTA)
5. Mike (itsMikey)
6. 90-irocdx3 (Name?)
7. if time allows
TA
#60
Senior Member
Join Date: Jul 2006
Location: 4-22 / 7-25
Posts: 811
Likes: 0
Received 2 Likes
on
2 Posts
Car: '91 Z28 L98 G92
Engine: Modded L98
Transmission: Modded 700R4
Axle/Gears: Modded 10-Bolt
Re: Dyno Day 2 (The Sequel)
RESULTS!
OK, let me start with saying that my results were achieved with an HSR intake. MY HSR will soon be equipped with a fully functional EGR system. 'Nuff said.
With some part throttle tuning by Kevin91Z, the base-line run was 382 rwhp / 346rwtq. (I thought we were looking at the wrong runfile...) Kevin added some fuel up top and the second pull was 385rwhp / 37xrwtq, 30 ft. / lb. gain.
Added some fuel up top, took some away down low. 387rwhp / 376rwtq.
It was still a tad lean up top, but Kevin discovered the injectors were maxed-out @ 109% duty cycle. It still had a little more power, if it had more fuel.
These pulls were made on the same dyno that indicated 321rwhp / 377rwtq with an Edelbrock base & modded SLP runners. No changes, other than the intake, were made. Oh, except a little work to open up the airlid outlet, and switching from a Flowmaster muffler to a Magnaflow muffler.
I was blown away.
Thanks to all present (Don, Kevin, Julie, Lon, Troy, Mike, Mikey, Vincent, Allen, Luis, Mark) for the help during the session. Everyone contributed, it was way cool.
Bill
P.S.: Do I have a hangover? Nope, but it wasn't for lack of trying.
OK, let me start with saying that my results were achieved with an HSR intake. MY HSR will soon be equipped with a fully functional EGR system. 'Nuff said.
With some part throttle tuning by Kevin91Z, the base-line run was 382 rwhp / 346rwtq. (I thought we were looking at the wrong runfile...) Kevin added some fuel up top and the second pull was 385rwhp / 37xrwtq, 30 ft. / lb. gain.
Added some fuel up top, took some away down low. 387rwhp / 376rwtq.
It was still a tad lean up top, but Kevin discovered the injectors were maxed-out @ 109% duty cycle. It still had a little more power, if it had more fuel.
These pulls were made on the same dyno that indicated 321rwhp / 377rwtq with an Edelbrock base & modded SLP runners. No changes, other than the intake, were made. Oh, except a little work to open up the airlid outlet, and switching from a Flowmaster muffler to a Magnaflow muffler.
I was blown away.
Thanks to all present (Don, Kevin, Julie, Lon, Troy, Mike, Mikey, Vincent, Allen, Luis, Mark) for the help during the session. Everyone contributed, it was way cool.
Bill
P.S.: Do I have a hangover? Nope, but it wasn't for lack of trying.
Last edited by Burnout91; 09-13-2009 at 11:44 AM. Reason: Forgot about the muffler.
#62
Supreme Member
iTrader: (3)
Re: Dyno Day 2 (The Sequel)
Congratulations Bill to a well built motor. Bill's car has a 700R4 tranny. By the way another example of Dyno Don short tubes headers making good power.
As a side note our Third Gens should make a real good showing at the LA Invitational next year. We should have quite a few low 12 second cars and most likely some in the 11's.
As a side note our Third Gens should make a real good showing at the LA Invitational next year. We should have quite a few low 12 second cars and most likely some in the 11's.
#63
Senior Member
Re: Dyno Day 2 (The Sequel)
I just had my car dynoed today. I got 181 hp and 190ft lbs. Now this is on a engine with 176,xxx miles edelbrock baseplate, SLP runners, magnaflow catback, k&n filters with gutted airbox, jegs stage 1 tune up kit, 24lb injectors, with a tune done by my neighbor. My car kept on kicking down to second gear though during the session. Do these numbers sound about right or do you guys think it sould of been better or worse?
#64
Supreme Member
iTrader: (7)
Join Date: Mar 2000
Location: Orange, CA
Posts: 5,674
Likes: 0
Received 106 Likes
on
65 Posts
Car: '90 Trans Am-12.45@110.71
Engine: 355 w/AFR 195's Elem. 400/430 HP/TQ
Transmission: Tremec T-56
Axle/Gears: 12 Bolt 3.73
Re: Dyno Day 2 (The Sequel)
You need help, that is not good.
A 305 should be about 205 325
A 305 should be about 205 325
#65
Senior Member
#67
Supreme Member
Join Date: Apr 2009
Location: Scottsdale, AZ
Posts: 2,852
Likes: 0
Received 1 Like
on
1 Post
Car: 89 GTA/93 S13/91 Si
Engine: 5.7 350 TPI
Transmission: 700R4
Axle/Gears: 3.23
Re: Dyno Day 2 (The Sequel)
I was happy with my results =] 250hp 328torque
Last edited by Kevin91Z; 09-14-2009 at 04:49 PM.
#72
Senior Member
#73
Senior Member
Join Date: Jul 2006
Location: 4-22 / 7-25
Posts: 811
Likes: 0
Received 2 Likes
on
2 Posts
Car: '91 Z28 L98 G92
Engine: Modded L98
Transmission: Modded 700R4
Axle/Gears: Modded 10-Bolt
Re: Dyno Day 2 (The Sequel)
Dyno Don, could you post the graph from my dyno run...having trouble opening those files. What was the barometric pressure?
Oh, nevermind...I just noticed you posted it, along with a comparison to your graph, over in the "TPI" forum.
Bill
Oh, nevermind...I just noticed you posted it, along with a comparison to your graph, over in the "TPI" forum.
Bill
Last edited by Burnout91; 09-16-2009 at 01:28 PM. Reason: Just noticed thread in "TPI" forum.
#74
Senior Member
Join Date: Jul 2006
Location: 4-22 / 7-25
Posts: 811
Likes: 0
Received 2 Likes
on
2 Posts
Car: '91 Z28 L98 G92
Engine: Modded L98
Transmission: Modded 700R4
Axle/Gears: Modded 10-Bolt
Re: Dyno Day 2 (The Sequel)
Trusted sources have discovered that the dyno's barometric pressure reference was indeed incorrect on 9/12/09...looks like my rwhp was ~363*. I still like it, love the powerband.
Bill
*More to follow...
Bill
*More to follow...
Last edited by Burnout91; 09-16-2009 at 04:23 PM.
#75
Supreme Member
Join Date: Apr 2009
Location: Scottsdale, AZ
Posts: 2,852
Likes: 0
Received 1 Like
on
1 Post
Car: 89 GTA/93 S13/91 Si
Engine: 5.7 350 TPI
Transmission: 700R4
Axle/Gears: 3.23
Re: Dyno Day 2 (The Sequel)
well i didnt really get to drive it till sunday cuz my dad made my mom drive it home >:/ but its running great..MPG is up..acceleration is definitly up..and all around it just feels great. THANKS KEVIN
#76
Supreme Member
iTrader: (7)
Join Date: Mar 2000
Location: Orange, CA
Posts: 5,674
Likes: 0
Received 106 Likes
on
65 Posts
Car: '90 Trans Am-12.45@110.71
Engine: 355 w/AFR 195's Elem. 400/430 HP/TQ
Transmission: Tremec T-56
Axle/Gears: 12 Bolt 3.73
Re: Dyno Day 2 (The Sequel)
Now correct that to what it really was, 30.2 and you do indeed have 380+
Remember, 28.6 is like 2000 ft. we were at sea level (30.2)
The machine was reading 363 uncorrected for that error in baro press.
Last edited by Dyno Don; 09-16-2009 at 05:57 PM.
#77
Member
iTrader: (1)
Join Date: Oct 2006
Location: Fulshear, TX
Posts: 115
Received 0 Likes
on
0 Posts
Car: 89 IROC Z-28
Engine: 5.7
Transmission: A4
Axle/Gears: 3.42
Re: Dyno Day 2 (The Sequel)
SURE you were at 363 Bill, but that was BEFORE 5000 RPM!!
Congrats Bill, can't wait till ya put some fuel in that animal!
Pat
Congrats Bill, can't wait till ya put some fuel in that animal!
Pat
#78
Senior Member
Join Date: Jul 2006
Location: 4-22 / 7-25
Posts: 811
Likes: 0
Received 2 Likes
on
2 Posts
Car: '91 Z28 L98 G92
Engine: Modded L98
Transmission: Modded 700R4
Axle/Gears: Modded 10-Bolt
Re: Dyno Day 2 (The Sequel)
I will post a full write-up; may be close to year-end before I have the time for the project.
OK, thanx Don
Injectors are on the way.
Bill
Bill
#79
Senior Member
Join Date: Jul 2001
Location: OC, CA
Posts: 783
Likes: 0
Received 1 Like
on
1 Post
Car: 92 Trans Am - Sold
Re: Dyno Day 2 (The Sequel)
Well, better late than never.
Here's a few videos from Dyno Day 2 Sept 2009.
http://www.youtube.com/view_play_lis...0A0C35C9876C1B
Here's a few videos from Dyno Day 2 Sept 2009.
http://www.youtube.com/view_play_lis...0A0C35C9876C1B
Thread
Thread Starter
Forum
Replies
Last Post
RedLeader289
Tech / General Engine
10
05-28-2019 01:47 PM
darwinprice
Organized Drag Racing and Autocross
17
10-11-2015 11:51 PM