Third Generation F-Body Message Boards

 
Page 1 of 3
1
2
3
Search: Posts Made By: rocn7roc
Showing results 1 to 50 of 114
Search took 0.10 seconds.
Forum: TPI
10-08-2019, 07:16 AM
Replies: 1
Views: 450
Posted By rocn7roc

tps sensor

87 camaro tps sensor set at .54 idle position, full throttle only gets to 3.66 have 5.0 volts reference. the sensor will go to 4.2 if I use my finger to max it out but the throttle wide open only...
Forum: Tech / General Engine
08-16-2018, 03:29 PM
Replies: 4
Views: 329
Posted By rocn7roc

Re: cruise control adjustment? seems jerky

Thanks On another issue is there any way to test to see if my purge cannister may of gotten deleted when it was reprogrammed for vats and Egr delete . Smelling gas fumes on hot days. Thanks Mike
Forum: TPI
08-16-2018, 01:58 PM
Replies: 55
Views: 3,886
Posted By rocn7roc

Re: Can you eliminate the purge cannister without problems?

I think my purge may have been disabled when he did the vats is there a easy to test for this? I am getting srtrong gas smell especially on hot days.Thanks Mike
Forum: Tech / General Engine
08-16-2018, 01:28 PM
Replies: 1
Views: 236
Posted By rocn7roc

91 camaro seems lopey on highway

Hi I have built my dream Camaro 91 convertible Rs added subframe connectors ,installed 86 Vette L98 with some mods mild porting to heads air plenun clean up etc Bosch injectors, Xtreme energy 262...
Forum: Tech / General Engine
08-16-2018, 12:46 PM
Replies: 4
Views: 329
Posted By rocn7roc

cruise control adjustment? seems jerky

Hi I have a 91 Camaro with an 86 L98 TPI ,got it all running and tried the cruise it does work but seems jerky at highway speeds.It accels to hard lets off does it all again. Is there some adjustment...
Forum: Body
08-14-2017, 07:51 AM
Replies: 2
Views: 510
Posted By rocn7roc

Re: Help 91 camaro convertiblewhere do these parts go .

Thanks so Much I knew I coudn't find a spot for them must of got mixed in with the vert parts from a car I parted thanks Mike
Forum: Convertibles
08-13-2017, 01:52 PM
Replies: 70
Important/Useful : Convertible Schematic Sheets
Views: 24,882
Posted By rocn7roc

Re: THANK YOU!!!

Hi I have a 91 vert I did a thread starter on a couple of trim pieces I can't figure out. Tiltle says Help 91 convertible trim pieces. Maybe you can Identify the Thanks Mike
Forum: Electronics
10-06-2016, 08:16 AM
Replies: 0
Views: 685
Posted By rocn7roc

Intellitronix dash update

Hi I purchased an Intellitronix digital dash for my 91 Camaro,received the dash and the sender.Instructions vary basic , The problem is I want to use my VSS signal to ecm to prevent stalling of my...
Forum: Electronics
09-30-2016, 09:32 AM
Replies: 11
Views: 14,028
Posted By rocn7roc

Re: New Inteliitronix Speedo (digital) and VSS questions

Hi I am going through the same grief with intellitronix what ecm do you have I have the 165 Maf ecm tat needs the 200 pulses by jumpering that with the 4000 pulse speedo wire it just doesn't make...
Forum: Engine Swap
09-24-2016, 09:21 AM
Replies: 2
Views: 550
Posted By rocn7roc

Re: 87 MAF TPI engine in 91 RS

Thanks for replying Don ,Maybe this a first for Maf in 91 I guess,Car is running Everything working need to test drive after bypassing buffer 2K VSS to Intellitronix dash. There is no neutral park...
Forum: Engine Swap
09-22-2016, 08:17 AM
Replies: 23
Views: 10,431
Posted By rocn7roc

Re: Install engine w or w/out headers.

Good way to do it don't install mount bolts in case you have to ;loft it a bit.I got away with out lifting but was tight,get that coolant steel pipe farther back too,it will hit.Good luck
Forum: Engine Swap
09-21-2016, 09:50 AM
Replies: 2
Views: 550
Posted By rocn7roc

87 MAF TPI engine in 91 RS

Hi I need a little guidance as I have swapped in a 87 TPI engine correct ecm WC T5 trans in my 91 RS that had the 305 TBI AUTo. It runs great .VSS hooked up but still dying occassionally on...
Forum: TPI
09-19-2016, 02:43 PM
Replies: 15
Views: 22,323
Posted By rocn7roc

Re: Vehicle Speed Sensor for 85-89 TPI

HI need help VSS sensor for my 89 Camaro 2pulse. Got part numbers can not find one Help Thanks Mike
Forum: TPI
09-18-2016, 09:29 AM
Replies: 15
Views: 22,323
Posted By rocn7roc

Re: Vehicle Speed Sensor for 85-89 TPI

Hi needing advise part number proper VSS sender for 87 Tpi engine T5 trans 3:23 gear using this in 91 RS Camaro engine runs good but stalling on decel. Appreciate any help Thanks Mike
Forum: Engine/Drivetrain/Suspension Parts for Sale
08-10-2016, 01:11 PM
Replies: 2
Views: 469
Posted By rocn7roc

Re: 92 Harness, ECM & TPI

Hi I need tpi air cleaner completeif you have one
Forum: Engine/Drivetrain/Suspension Parts for Sale
08-10-2016, 01:09 PM
Replies: 101
Views: 19,995
Posted By rocn7roc

Re: Parting out 1992 z28 tpi 5 speed car

I need a air cleaner setup in ggod shape will that one fit car with maf If so how much shipped to52151
Forum: Engine/Drivetrain/Suspension Parts for Sale
08-10-2016, 01:06 PM
Replies: 44
Views: 2,536
Posted By rocn7roc

Re: Parting out 89 camaro

I need a tpi air cleaner in good shape complete
Forum: Alternative Port EFI Intakes
08-10-2016, 12:47 PM
Replies: 200
Views: 74,281
Posted By rocn7roc

Re: Aftermarket Cold Air Intake

What reducer do you need off the throttle body
Forum: Transmissions and Drivetrain
07-15-2016, 05:29 PM
Replies: 0
Views: 400
Posted By rocn7roc

t5 shifter handle length

Doing a t5 conversion what would be the best length shifter to clear console and be comfortable and hold boot in place, and does any one know the stock length from mounting flange of tranny to...
Forum: Engine Swap
07-02-2016, 08:05 AM
Replies: 2
Views: 649
Posted By rocn7roc

Re: auto to T5 swap

ThANKS
Forum: Engine Swap
07-01-2016, 04:39 PM
Replies: 2
Views: 649
Posted By rocn7roc

auto to T5 swap

Hi putting car back together and the torque arm from auto car doesn't match up to my T5 rubber bushing, Are the torque arms different, could a guy swap out the rubber bushing to match Thanks Mike
Forum: Engine/Drivetrain/Suspension Parts for Sale
07-01-2016, 04:35 PM
Replies: 101
Views: 19,995
Posted By rocn7roc

Re: Parting out 1992 z28 tpi 5 speed car

Hi do you know if the torque arms are different t5 vs auto I am doing conversion and the rubber bushing looks different ,don't line up Do you still have the torque arm
Forum: Interior
01-01-2016, 09:08 AM
Replies: 22
Views: 19,311
Posted By rocn7roc

Re: My intellitronix gauge install

I have one also when you turn on lights it dims down non adjustable
Forum: Electronics
01-01-2016, 08:58 AM
Replies: 1
Views: 494
Posted By rocn7roc

Vss signal Help

Hi I may have discovered another issue in my Camaro build ,I have 91 camaro using 86 corvettte maf engine that requires 2000 vss signal for ecm .I am using the programmable dakota digital dash 4000...
Forum: Engine/Drivetrain/Suspension Parts for Sale
10-22-2015, 08:30 AM
Replies: 2
Views: 681
Posted By rocn7roc

Re: TPI Snorkle And Air Box $50

Do you still have this?
Forum: Engine/Drivetrain/Suspension Parts for Sale
10-22-2015, 08:16 AM
Replies: 10
Views: 1,279
Posted By rocn7roc

Re: 98-02 "LS1" Front brakes

Besides these parts what are the cost for rotors and the adapter kit thanks Mike
Forum: Camaros for Sale
10-22-2015, 08:11 AM
Replies: 35
Views: 1,289,382
Posted By rocn7roc

Re: 1990 Camaro RS Modified

Nice car well worth the money,where did you get your front turn signals ,mine are dull and would like to replace Thanks Mike
Forum: Electronics
10-22-2015, 07:53 AM
Replies: 10
Views: 32,637
Posted By rocn7roc

Re: 91 Camaro intellitronix gauge install

Great posting I may need some advise when I wire it this winter Appreciate the pics Too Thanks MIke
Forum: Electronics
10-22-2015, 07:49 AM
Replies: 10
Views: 32,637
Posted By rocn7roc

Re: 91 Camaro intellitronix gauge install

yes they lined up any thing you could share about this install would be appreciated Thanks Mike
Forum: Electronics
08-08-2015, 12:34 PM
Replies: 10
Views: 32,637
Posted By rocn7roc

91 Camaro intellitronix gauge install

Hi I am going to be installing these gauge in my 91 camaro, I would like to wire gauges so they plug in to Dash recepticle plug in so I would not have a bunch of wires exposed. has any done this and...
Forum: Engine/Drivetrain/Suspension Parts for Sale
07-16-2015, 03:51 PM
Replies: 100
Views: 9,519
Posted By rocn7roc

Re: 3rd Gen Parts

Need fog lights and dual fan brackets can you help?52151 zip Thanks Mike
Forum: Interior Parts Wanted
07-06-2015, 11:17 AM
Replies: 1
Views: 288
Posted By rocn7roc

Wanted 82-02 dark grey or black seat set

Hi need full seat set for my 91 Camaro,must be excellent condition no burns or rips, can be two tone black grey also. I live in NE Iowa so Wi. and Mn are driveable for me.
Forum: Aftermarket Product Review
05-24-2015, 11:28 AM
Replies: 177
Views: 117,688
Posted By rocn7roc

Re: Best brand Camaro Subframe Connectors? (IROC Z)

They look strong ,being a fab guy would like to make my own.Nice job
Forum: Electronics
03-17-2015, 09:01 AM
Replies: 4
Views: 606
Posted By rocn7roc

Re: Wiring advise needed Maf engine 91 camaro

Want the maf have cam and headers, I just meant vats signal wire and the vats will be deleted in the prom.
Forum: Electronics
03-14-2015, 12:26 PM
Replies: 4
Views: 606
Posted By rocn7roc

Wiring advise needed Maf engine 91 camaro

Installing 86 Corvette maf engine that has vats which I will have the prom delete that .The car is a 91 so it has the vats system and the harness I am using is an 87 Camaro maf that has no wire in...
Forum: Convertibles
03-05-2015, 04:47 PM
Replies: 6
Views: 2,297
Posted By rocn7roc

Re: convertible back seat same as coupe?

HI I am near Lacrosse got any connection for grey or black seats set must be no rips or burns thanks Mike
Forum: Interior
03-04-2015, 01:41 PM
Replies: 212
Views: 50,212
Posted By rocn7roc

Re: 90-92 Intellitronix Digi Dash Prototype In My Hands!

How is the connection made to the computer for VSS from the speedo or speed sensor so as not to set off a code Thanks Mike
Forum: LTX and LSX
08-18-2014, 08:24 AM
Replies: 64
Views: 67,930
Posted By rocn7roc

Re: Additional swap information

Pocket THANK YOU so much for all your info I am installing 86 vette MAF engine in my 91 RS TBI car and this is so valuable to me. Is there any other details about that C100 or other things I may...
Forum: Electronics
08-13-2014, 05:32 PM
Replies: 1
Views: 536
Posted By rocn7roc

86 tpi maf in a 91 RS need advise

Hi need some imput on my project car, first a little back ground i am 60 years old and enjoy my Chevies 57 chevy truck and car I restored and installed tpi engines.Made my own harnesses from junk...
Forum: Electronics
07-29-2014, 04:45 PM
Replies: 1
Views: 423
Posted By rocn7roc

swapping out tbi harness for tpi harness

Hi I am in the process of installing tpi in my 91 rs Camaro,Can any one give me tips on the best way to remove and replace this harness ,what is the routing does it go back in to the dash area.Where...
Forum: Exterior Parts for Sale
07-10-2014, 11:11 AM
Replies: 57
Views: 3,174
Posted By rocn7roc

Re: Parting out a 91 Camaro

looking for a good trunk pulldown assbly,for my 91 rs it is metal frame where it bolts to thanks mike
Forum: Transmissions and Drivetrain
07-05-2014, 03:06 PM
Replies: 14
Views: 8,587
Posted By rocn7roc

Re: T5 swap question

Hi I am doing this conversion also,what wiring changes do i need to make ,neutral switch ,clutch pedal switch, steering column lock cable fro auto shifter Thanks Mike
Forum: Aftermarket Vendor Review
07-03-2014, 08:27 AM
Replies: 24
Views: 2,013
Posted By rocn7roc

Re: Thumbs Up for Lon @ TDS.

There are 3 types of trunk pull downs do they interchange with wiring modifications, looks like mine is 86-90 style on my 91 Thanks Mike
Forum: Exterior Parts for Sale
06-29-2014, 10:15 AM
Replies: 3
Views: 682
Posted By rocn7roc

Re: 91-92 hood blisters

Hi would 100$ plus 20$ shipping be a good offer Mike I am trying to find something local but not having much luck
Forum: Exterior Parts Wanted
06-24-2014, 08:29 AM
Replies: 0
Views: 216
Posted By rocn7roc

Wanted 91-92 Z28 hood with blisters

Hi Looking for a good used 91-92 Z28 hood with the Blisters I can pick up we live in NE Iowa near SW Wi and southern MN and Iowa pick up 319-239-1878 Thanks Mike
Forum: Transmissions and Drivetrain
06-08-2014, 07:44 AM
Replies: 13
Views: 4,932
Posted By rocn7roc

Re: 4th gen posi diff in a 3rd gen housing

Thanks I got the same torsen for the 91 RS should I buy the 99-02 kit or the 86-98 bearing install kit? Thanks for your help Mike?
Forum: Engine/Drivetrain/Suspension Parts for Sale
05-12-2014, 08:24 AM
Replies: 34
Views: 2,822
Posted By rocn7roc

Re: Lots of parts for sale!!! what do you need!

I parted a 91 Gta probly have what you need,let me know
Forum: Engine/Drivetrain/Suspension Parts for Sale
12-26-2013, 10:49 AM
Replies: 6
Views: 689
Posted By rocn7roc

Re: Headers &Ypipe

Do you still have and what model ?
Forum: Engine/Drivetrain/Suspension Parts for Sale
12-26-2013, 10:20 AM
Replies: 61
Views: 4,324
Posted By rocn7roc

Re: parting out 1987 iroc z28 tpi 5 speed

Brain fart I have the 91 so no workie Thanks Mike
Showing results 1 to 50 of 114
 
Page 1 of 3
1
2
3


 
Forum Jump


All times are GMT -5. The time now is 01:25 PM.