Search Results

Views: 1,210

Posted By ibmtech

Re: Too much power not enough tire

I have been told about the 4L80E very little.. Would the 6L80E be a good candidate to put in? A friend of mine is pulling his and putting in a manual shift as he doesn't like auto..

Forum: Wheels and Tires

12-01-2013, 07:39 PM

Replies: 14

Views: 1,210

Posted By ibmtech

Re: Too much power not enough tire

Actually, it is 927 at rear wheel on that trans... I have gone through 3 of them through prebuilt and was guaranteed that this one would hold.. I have been very patient with them but have a 400hyd...

Forum: Wheels and Tires

12-01-2013, 07:14 PM

Replies: 14

Views: 1,210

Posted By ibmtech

Re: Too much power not enough tire

I have full aftermarket suspension. My signature doesn't give me a lot of room to enter everything I have done to the car.

Forum: Interior

12-01-2013, 09:58 AM

Replies: 10

Speedometer Swap

Views: 1,335

Posted By ibmtech

Re: Speedometer Swap

This whole thing about mileage only becomes illegal if you are attempting to sell the car attempting to make the buying believe it has less mileage than it actually does. Other than that, It is your...

Forum: Wheels and Tires

12-01-2013, 09:34 AM

Replies: 14

put a new ecm in and check engine light flashing rapidly

Views: 1,210

Posted By ibmtech

Re: Too much power not enough tire

ok now that leads to the 2nd part of my question.. I like the tires.. I know they are 15 inch x 10.5 now how do I figure out offset currently with the rear end that I have so I can get the proper...

Forum: DFI and ECM

12-01-2013, 07:51 AM

Replies: 19

Computer/ECM removal?

Views: 9,115

Posted By ibmtech

Re: Computer/ECM removal?

I think you have to have ask the one of senior webmasters to change your name...

Forum: DFI and ECM

12-01-2013, 07:47 AM

Replies: 4

Views: 7,665

Posted By ibmtech

Re: put a new ecm in and check engine light flashing rapidly

Did you remember to put the prom in the new ECM when you got it?

Forum: Tech / General Engine

12-01-2013, 07:44 AM

Replies: 6

Ignition switch help!!!

Views: 1,306

Posted By ibmtech

Re: Ignition switch help!!!

When I changed mine about a month ago, I had to have in the off position.

Forum: Wheels and Tires

12-01-2013, 07:40 AM

Replies: 14

Views: 1,210

Posted By ibmtech

Too much power not enough tire

With that being said, I need to get more sneaker on the ground. I am currently still running the original 16x8 rim's to drive around town.. But, I know when I want to play, I will need a larger rim,...

Forum: Engine Swap

11-24-2013, 09:12 PM

Replies: 5

Wiring a 350 with a 6-71

Views: 870

Posted By ibmtech

Re: Wiring a 350 with a 6-71

The only wires that you will need that come out the passenger side are for the heater and A/C if still using this and the electric fans. All the rest of the wires don't apply for your setup any more.

Forum: Body

11-24-2013, 09:37 AM

Replies: 29

140 speedo can i get faster

Views: 2,336

Posted By ibmtech

Re: 140 speedo can i get faster

I still have my Series 2 Dakota Digital Dash for sale for $200 if anyone is still interested.. I took it out about 3 months ago to install the newest Dakota Dash after I returned back from...

Forum: Power Adders

08-06-2013, 07:36 AM

Replies: 8

Fueling Ideas for S/C

Views: 627

Posted By ibmtech

Re: Fueling Ideas for S/C

Exactly,, I am pushing almost 700 now, and I need to find out what the 400 is capable of supporting..

I do like the idea of the areomotive 340lph pump that Project89 suggested... Hopefully he can...

Forum: Power Adders

08-05-2013, 10:42 PM

Replies: 8

Fueling Ideas for S/C

Views: 627

Posted By ibmtech

Fueling Ideas for S/C

While on the Dyno last Sunday:

87 IROC using -6 AN fuel supply and feed line with a 434 on a Vortech S/C using a 3:48 pulley got me 5 lbs of boost at 6500 rpm and I couldn't get enough fuel while...

Forum: Exhaust

05-21-2013, 02:27 PM

Replies: 243

4 reasons why you should remove the AIR (smog) pump

Views: 230,666

Posted By ibmtech

Re: 4 reasons why you should remove the AIR (smog) pump

thanks Kevin91Z as I have removed anything that involves emission's and make way, way over 375 horsepower to the wheels. I live in NY just on the other side of St. Lawrence River across from...

Forum: Exhaust

05-15-2013, 10:14 AM

Replies: 243

4 reasons why you should remove the AIR (smog) pump

Views: 230,666

Posted By ibmtech

Re: 4 reasons why you should remove the AIR (smog) pump

The only bad thing about that entire rant and rave, When ChargerBill wrote, "the amount of wasted resources seem to counter the objectives."

But he isn't taking into account that the cars back...

Forum: Power Adders

03-12-2013, 11:45 AM

Replies: 122

91 camaro twin turbo 406 build thread

Views: 14,165

Posted By ibmtech

Re: 91 camaro twin turbo 406 build thread

Why don't you go with the dart iron eagle instead of the little m? I went through ultrastreet.net when I ordered mine.. Just curious

Forum: Fabrication

02-27-2013, 10:56 AM

Replies: 23

LED sequential tail lights for a Camaro

Views: 8,035

Posted By ibmtech

Re: LED sequential tail lights for a Camaro

I just purchased mine and they are sequential.. I haven't got them installed am working on it now.

https://www.classicindustries.com/search?q=500889

Currently working on website but will upload...

Forum: Exhaust

02-20-2013, 08:35 AM

Replies: 50

Upside Down Headers?

Views: 25,178

Posted By ibmtech

Re: Upside Down Headers?

Running them through the hood isn't a good idea because

1. The exhaust is blowing will be blowing right at the windshield..
2. You will have an extremely loud car.
3. You won't be able to...

Forum: DFI and ECM

02-14-2013, 08:31 PM

Replies: 85

Chip for better milage

Views: 3,116

Posted By ibmtech

Re: Chip for better milage

:thumbsup::iagree:

Forum: Tech / General Engine

02-11-2013, 09:32 PM

Replies: 17

Views: 791

Posted By ibmtech

Re: not a f-body but need some help desperately

Sent you a private message..

Forum: Tech / General Engine

02-11-2013, 09:26 PM

Replies: 17

Views: 791

Posted By ibmtech

Re: not a f-body but need some help desperately

We will work on injectors next if I can keep my open long enough.

Have you checked the fuse block for the 10Amp fuse to see it is good ? You can see the fuse blockon 94 Chevy 2.pdf for reference.

Forum: Tech / General Engine

02-11-2013, 09:22 PM

Replies: 17

Views: 791

Posted By ibmtech

Re: not a f-body but need some help desperately

Now disconnect that jumper from the + POS side of the battery and the GRY wire.

Then with the fuel pump relay plugged into the harness... now take a jumper wire from the Black wire w/ white...

Forum: Tech / General Engine

02-11-2013, 09:18 PM

Replies: 17

Views: 791

Posted By ibmtech

Re: not a f-body but need some help desperately

Remember not to leave that jumper in there as it will burn your Fuel pump motor out.. This is just a check for your fuel pump for diagnosis

Forum: Tech / General Engine

02-11-2013, 09:16 PM

Replies: 17

Views: 791

Posted By ibmtech

Re: not a f-body but need some help desperately

The purple wire is the + side of the fuel solenoid to provide enough voltage to the solenoid to activate the switch using the orange wire from the Fuel pump prime connector (Red Wire) and changes it...

Forum: Tech / General Engine

02-11-2013, 09:12 PM

Replies: 17

Views: 791

Posted By ibmtech

Re: not a f-body but need some help desperately

Sorry, the purple is fed by the ECM... My Bad

Can you make a jumper wire from the Grey wire directly to the battery + side and see if your fuel pump works?

Forum: Tech / General Engine

02-11-2013, 09:08 PM

Replies: 17

Views: 791

Posted By ibmtech

Re: not a f-body but need some help desperately

Purple ??? On the fuel pump relay, You should have 4 wires. According to the diagram 94 chevy 3.pdf

Grey
Red
Orange
Black w/ white stripe..

Do you have power at the orange wire ? It...

Forum: Tech / General Engine

02-11-2013, 08:58 PM

Replies: 17

Views: 791

Posted By ibmtech

Re: not a f-body but need some help desperately

Do you have 12 volts at the org wire with the on the fuel pump relay with the key in the off and on position ?

Forum: Tech / General Engine

02-11-2013, 08:44 PM

Replies: 17

Views: 791

Posted By ibmtech

Re: not a f-body but need some help desperately

You can see from the diagrams that the Ignition module (EST) wires only feed into the ecm.. They don't have anything to do with fuel..

Found another schematic that don't have anything to do with...

Forum: Tech / General Engine

02-11-2013, 08:34 PM

Replies: 17

Views: 791

Posted By ibmtech

Re: not a f-body but need some help desperately

There could be a few culprit wires.. The Grey one needs to be tested for voltage.. The Fuel Pump relay and the Fuel pump as you see it feeds both items.. I would start there and check for 12+ on...

Forum: Tech / General Engine

02-11-2013, 08:11 PM

Replies: 17

Coolant leak, need to replace gaskets to fix. What is the name of this part (pics).

Views: 791

Posted By ibmtech

Re: not a f-body but need some help desperately

Enclosed are the schematics required for your vehicle... You will mainly need 94 Chevy 1 & 3 PDF

You are stating that you are only getting 8.9v to the pump.. That would indicate a bad wire.. Pumps...

Forum: V6

02-11-2013, 07:50 PM

Replies: 51

Views: 6,472

Posted By ibmtech

Re: Coolant leak, need to replace gaskets to fix. What is the name of this part (pics

I would rather have a freeze plug pop then a head gasket .. The rubber ones will hold you over for a while...

:iagree:

Forum: Alternative Port EFI Intakes

02-08-2013, 10:00 PM

Replies: 12

AFR 210's, Mini-Ram, 355 N/A

Views: 2,645

Posted By ibmtech

Re: AFR 210's, Mini-Ram, 355 N/A

I used to use the 210cfm with 75 cc CNC heads part number was #1100 on a 355 with a Vortech Supercharger and ran into a ton of issues with tuning. I now have a 434 CID and just torqued the heads down...

Forum: TPI

02-08-2013, 09:37 PM

Replies: 4

TPI Removal

Views: 896

Posted By ibmtech

Re: TPI Removal

Did you already drain your coolant ? If not your might want to pull your knock sensor on the bottom of the block to drain your block and drain your radiator before you pull the heads so you don't get...

Forum: TPI

02-08-2013, 09:25 PM

Replies: 4

Tpi won't run

Views: 430

Posted By ibmtech

Re: Tpi won't run

Classic thing that I discovered. Once your plugs get fuel saturated, don't reuse them, Replace them. I have tried to reused old plugs by burning off the excess fuel and it just doesn't work as well...

Forum: TPI

02-08-2013, 09:20 PM

Replies: 4

Tpi won't run

Views: 430

Posted By ibmtech

Re: Tpi won't run

Make sure that NO#1 cylinder is up on TDC on the (Compression Stroke) not (exhaust stroke) or your timing will be off 180 degrees

You can disconnect your ALDL wire prior to attempting to start...

Forum: Exhaust

02-08-2013, 09:13 PM

Replies: 3

EGR stem rusted onto manifold! Help.

Views: 737

Posted By ibmtech

Re: EGR stem rusted onto manifold! Help.

Depends on your local state law on your emissions. Depending on where I go in N.Y. certain garages will not pass my car because I removed all emissions (Air Pump, EGR, Cat, AIRE manifolds, Bypass...

Forum: TBI

02-08-2013, 09:07 PM

Replies: 7

Magical mysterious code 13 and code 43

Views: 3,263

Posted By ibmtech

Re: Magical mysterious code 13 and code 43

:yup:

Your TPS setting is a little high also.. Not outragious though. I have seen some people set their at 1.54 for their Low Voltage at idle and I don't understand why. I think it should be...

Forum: Tech / General Engine

01-31-2013, 05:38 PM

Replies: 27

L98 wont stay running

Views: 2,146

Posted By ibmtech

Re: L98 wont stay running

A vaccum leak will cause the engine to run at a higher RPM

Forum: Suspension and Chassis

01-30-2013, 07:13 PM

Replies: 86

Views: 10,342

Posted By ibmtech

Re: Suspension question

:doh:
That figures.. I will keep that in mind when they come in. I know someone that has the 1LE that will buy them..

Forum: Suspension and Chassis

01-30-2013, 06:55 PM

Replies: 86

Views: 10,342

Posted By ibmtech

Re: Suspension question

Ok, you got me convinced... I'll keep the same calipers.. LOL.. I will just get them cleaned up... I did order a bunch of other crap that I need though.

1 EIB-3-Pro Eibach Pro Performance...

Forum: Suspension and Chassis

01-30-2013, 03:44 PM

Replies: 86

Back hatch wont open? Anyway i can pop it another way??

Views: 10,342

Posted By ibmtech

Re: Suspension question

Money isn't really an option.. My brakes have a good feel to them currently, I just don't know if they will handle what I have in the future.. I was additionally looking at the PBR setup on Spohn.net...

Forum: Aftermarket Product Review

01-30-2013, 11:56 AM

Replies: 40

Camaro Daytona Hood/Turbo Hood (POST PICTURES)

Views: 16,953

Posted By ibmtech

Re: Camaro Daytona Hood/Turbo Hood (POST PICTURES)

http://www.cardomain.com/gallery/8701359

http://www.cardomain.com/gallery/8701361

http://www.cardomain.com/gallery/8701389

Forum: Electronics

01-30-2013, 08:58 AM

Replies: 1

Views: 530

Posted By ibmtech

Re: Back hatch wont open? Anyway i can pop it another way??

Pull your senter console where your window and trunk switch's are.. put the Trunk wire directly to another 12+ wire to activate the motor and open the trunk .

Forum: Suspension and Chassis

01-30-2013, 08:55 AM

Replies: 86

Views: 10,342

Posted By ibmtech

Re: Suspension question

So does anyone have any Rotors / calipers they recommed.

Forum: Suspension and Chassis

01-29-2013, 08:08 PM

Replies: 86

Views: 10,342

Posted By ibmtech

Re: Suspension question

You have given me a plethura of information on brakes and I can understand that I really don't need other brakes because they appear better and I can save alot of money now. You don't like drilled...

Forum: Suspension and Chassis

01-29-2013, 11:57 AM

Replies: 86