Third Generation F-Body Message Boards

Search: Posts Made By: cz350Z
Showing results 1 to 12 of 12
Search took 0.13 seconds.
Forum: Tech / General Engine
12-24-2003, 07:55 PM
Replies: 70
Views: 1,713
Posted By cz350Z

Think about our roof and all that rains back on...

Think about our roof and all that rains back on us. I can admit I'm one of the first people that will would and did hack emission stuff after learning how much more extra power I will get from it.I...
Forum: Tech / General Engine
12-24-2003, 06:51 PM
Replies: 9
Views: 452
Posted By cz350Z

I left out the module cause they usually act up...

I left out the module cause they usually act up after the engine heats. If it was my car I'd try dropping another distributor in it to make sure the pick up coil is ok,or have it put on a bench and...
Forum: Tech / General Engine
12-24-2003, 04:18 PM
Replies: 12
Views: 496
Posted By cz350Z

I'd spend the extra $ and bump the compression a...

I'd spend the extra $ and bump the compression a lil while everything is apart. Then pic a cam to compliment everything. Even if you go a little bigger on the cam now your motor will shine when you...
Forum: Tech / General Engine
12-24-2003, 12:14 PM
Replies: 9
Views: 452
Posted By cz350Z

I had a simalar thing happening last summer. A...

I had a simalar thing happening last summer. A week or so after doing a complete tune up,( cap rotor wires and plugs) Drove me crazy cause I ran outa' places to look for trouble. I also tried...
Forum: Tech / General Engine
12-18-2003, 05:59 PM
Replies: 8
Views: 707
Posted By cz350Z

You can also try heating the head of the bolt...

You can also try heating the head of the bolt slightly with a propane torch so it expands the metal and causes the threads to grip better. This old croation machinest at my work told me that. Just be...
Forum: Tech / General Engine
12-18-2003, 05:25 PM
Replies: 10
Views: 616
Posted By cz350Z

If someone has one of those programs to estimate...

If someone has one of those programs to estimate better that be sweet. I want my compression roughly the same. Heads and push rods are puttin' the squeeze on my funds for a bit. If I over do it...
Forum: Tech / General Engine
12-18-2003, 01:34 PM
Replies: 10
Views: 616
Posted By cz350Z

Sweet! Thats what I like to hear . Hey Daemorok ,...

Sweet! Thats what I like to hear . Hey Daemorok , what cam are you running in your car ? I'm also curious to know if your useing dished pistons . And if yes , were the 64cc chambers put your...
Forum: Tech / General Engine
12-18-2003, 12:26 PM
Replies: 10
Views: 616
Posted By cz350Z

I'm leaning more toward the 180cc size now . Dart...

I'm leaning more toward the 180cc size now . Dart does'nt have theres listed with the 1.94 valves . Maybe I'd be ok with the next size up? . I'm going to see what I can dig up on the pro toplines...
Forum: Tech / General Engine
12-18-2003, 12:05 AM
Replies: 10
Views: 616
Posted By cz350Z

I came to the understanding that smaller runners...

I came to the understanding that smaller runners will help to build up more torque . So going with the 165's might be a better choice . Upon doing more thinking , I thought maybe I'd still get that...
Forum: Tech / General Engine
12-17-2003, 07:38 PM
Replies: 8
Views: 707
Posted By cz350Z

Did you try locking vise-grips on it and pulling...

Did you try locking vise-grips on it and pulling up as you turn?
Forum: Exhaust
12-17-2003, 06:00 PM
Replies: 19
Views: 725
Posted By cz350Z

When I hollowed out my cat my car seems to lose...

When I hollowed out my cat my car seems to lose power . I would'nt say it sounded too great either . I was told the same thing that purple82 mentioned , the bigger open chamber causes turbulance...
Forum: Tech / General Engine
12-17-2003, 05:29 PM
Replies: 10
Views: 616
Posted By cz350Z

new heads

What are your thoughts on the dart iron eagles ? Originally I was thinking about getting the 165cc 1.94 / 1.50 eagle s/s' . CHP flow bench results were 195 cfm@ 0.400 . I'm looking for as much...
Showing results 1 to 12 of 12


 
Forum Jump


All times are GMT -5. The time now is 10:05 PM.