Third Generation F-Body Message Boards

Search: Posts Made By: 63a
Showing results 1 to 14 of 14
Search took 0.02 seconds.
Forum: DFI and ECM
09-13-2022, 02:14 PM
Replies: 0
Views: 206
Posted By 63a

stock ECM (7727) convert to EBL or MS

I apologize if this question has been asked/answered repeatedly but I think I've read so many tuning posts that I'm considering going back to carb and points.

I dont have a thirdgen but my car has...
Forum: Tech / General Engine
06-10-2019, 12:28 PM
Replies: 0
Views: 712
Posted By 63a

ignition module troubleshooting

Project car has a 1999 3.1 V6 using a 7727 ECM and harness from a 92 Lumina 3.1. Car has been running great but died a few days ago. I quickly found the blown 10A ignition fuse and replaced it. ...
Forum: Electronics
10-04-2018, 11:36 PM
Replies: 10
Views: 1,778
Posted By 63a

Re: tach issue

Thanks for all your help- finally got the tach working.
Forum: Electronics
09-28-2018, 09:15 AM
Replies: 10
Views: 1,778
Posted By 63a

Re: tach issue

Great - thanks for the info. I'll go to the electronics supply this weekend and get the parts.

I've seen several threads showing which resistor to replace/modify on the Camaro tach board but...
Forum: Electronics
09-28-2018, 12:40 AM
Replies: 10
Views: 1,778
Posted By 63a

Re: tach issue

Thanks Bob. Work puled me away for a few days but now need to get back at it.

I copied your adapter instructions from the link but have a few questions-
For the level shifter (tach), use a...
Forum: Electronics
09-21-2018, 10:17 PM
Replies: 10
Views: 1,778
Posted By 63a

Re: tach issue

Bummer- hoping that might be a workaround. I built a converter from an old relay using the instructions in the link below but it did not make a difference on the tach. The converter did increase...
Forum: Electronics
09-20-2018, 04:09 PM
Replies: 10
Views: 1,778
Posted By 63a

Re: tach issue

Thanks Bob. I'll see what I can find on google for up converting the tach signal to 0-12V but if you have a link that would be great.

Is the EST signal from the ICM to the ECM a 0-12V pulse? ...
Forum: Electronics
09-19-2018, 09:59 PM
Replies: 10
Views: 1,778
Posted By 63a

Re: tach issue

I did check the 2 Firebird V6 tachs with a battery charger and both appear to working correctly - showed 2400RPM when connected to charger.
Forum: Electronics
09-19-2018, 09:10 PM
Replies: 10
Views: 1,778
Posted By 63a

tach issue

I don't have a 3rd gen Camaro/Firebird but I've used many 3rd gen parts in my project car so I hope posting here is OK

I installed a 3100 V6 in my Opel Kadett and all is working great except for a...
Forum: Engine/Drivetrain/Suspension Wanted
05-06-2015, 06:23 AM
Replies: 4
Views: 372
Posted By 63a

Re: Wanted: 2.8/3.1/3.4 V6 timing cover/ balancer/pulleys- TX

Eric and Eddie,
Thanks for the replies. I'm hoping to get all the parts in one shot so will wait to see if anybody has a timing cover, balancer and pulleys. If that doesn't happen will PM you.
...
Forum: Engine/Drivetrain/Suspension Wanted
05-05-2015, 08:22 PM
Replies: 4
Views: 372
Posted By 63a

Wanted: 2.8/3.1/3.4 V6 timing cover/ balancer/pulleys- TX

Looking for timing cover, harmonic balancer, crank pulley and water pump pulley for 1988-up 2.8/3.1/3.4 V6. I'm doing a 3400 RWD swap so I need the timing cover from 88 or newer to work with the FWD...
Forum: Engine/Drivetrain/Suspension Wanted
07-29-2013, 11:12 AM
Replies: 6
Views: 405
Posted By 63a

Re: WTB: T5 trans- good or bad

BigBubba,
I shipped a T5 with Fedex ground a few years ago and the cost wasn't too bad. I sent you a PM.

Thanks
Forum: Engine/Drivetrain/Suspension Wanted
07-29-2013, 08:05 AM
Replies: 6
Views: 405
Posted By 63a

Re: WTB: T5 trans- good or bad

Pardon my ignorance, but which mounting face (GM or Ford) does your transmission have. I know some of the V6 T5s use the Ford pattern but don't know which ones.

Thanks
Forum: Engine/Drivetrain/Suspension Wanted
07-28-2013, 11:29 PM
Replies: 6
Views: 405
Posted By 63a

WTB: T5 trans- good or bad

Looking for V8 T5 trans- WC or NWC- will be behind a V6 in 1700lb car so NWC should be fine. Prefer V8 trans for ratios but will consider V6 T5.

Will consider good (ready to bolt in) or bad...
Showing results 1 to 14 of 14


 
Forum Jump


All times are GMT -5. The time now is 04:24 PM.