Third Generation F-Body Message Boards

Search: Posts Made By: Cadride
Showing results 1 to 44 of 44
Search took 0.03 seconds.
Forum: DIY PROM
07-02-2014, 07:24 AM
Replies: 5,155
Views: 636,499
Posted By Cadride

Re: Tuning with the EBL

I working on dialing in BST - Boost PW Multiplier % (2-Bar) table and was wondering if I would be ok to increase the RPM that PE kicks in to 6000; as I won’t be working in that rpm range right now?...
Forum: Power Adders
05-10-2014, 08:51 AM
Replies: 9
Views: 2,948
Posted By Cadride

Re: Methanol Injector Placement

Sorry Guys for falling off the face of the earth. I am currently taking 12 credit hours at the university and full time work and at the end of the semester my class projects got the best of me and...
Forum: Power Adders
04-15-2014, 12:06 PM
Replies: 9
Views: 2,948
Posted By Cadride

Re: Methanol Injector Placement

I contemplated long and hard about doing an port setup, but I was already pretty far down the path with the TB setup when I was considering sending my manifold out to be setup with an injector ports...
Forum: Power Adders
04-11-2014, 12:08 PM
Replies: 9
Views: 2,948
Posted By Cadride

Re: Methanol Injector Placement

I have considered putting it in the TB which I will take another look at tonight. The walls are pretty thin; its a 454 TB bored an additional 4mm per bore to 54mm. Then to make the walls even thinner...
Forum: Power Adders
04-10-2014, 10:40 PM
Replies: 9
Views: 2,948
Posted By Cadride

Re: Methanol Injector Placement

Pocket thanks for the reply.
The current location of the IAT is post SC and post Innercooler as shown below.
337235
With my setup there would be only 1” from the nozzle to the innercooler if I...
Forum: Power Adders
04-05-2014, 09:11 PM
Replies: 9
Views: 2,948
Posted By Cadride

Methanol Injector Placement

Looking for some help on the best place to put a methanol injector? With my setup, I want to inject post SC to keep methanol from misting the air cleaner. Unfortunately, I have limited space to make...
Forum: Engine/Drivetrain/Suspension Wanted
02-25-2014, 07:20 AM
Replies: 0
Views: 214
Posted By Cadride

Wanted EBL Dynamic EFI Flash Switcher

I am interested in purchasing a Flash Switcher for the dynamic EFI Setup. Please PM if you have one available. Will pay $75 for good unit.
Forum: DIY PROM
02-13-2014, 11:16 PM
Replies: 5,155
Views: 636,499
Posted By Cadride

Re: Tuning with the EBL

One thing that really helped me in smoothing the engine out; was after doing VE learns look at the table in the graph and smooth out the low and high points. I did this to many tables and made it run...
Forum: DIY PROM
02-13-2014, 11:15 PM
Replies: 5,155
Views: 636,499
Posted By Cadride

Re: Tuning with the EBL

One thing that really helped me out in smoothing the engine out; was after doing VE learns look at the table in the graph and smooth out the low and high points. I did this to many tables and made it...
Forum: Power Adders
02-04-2014, 08:51 AM
Replies: 85
Views: 14,106
Posted By Cadride

Re: Almost done with SC install on 355 with 454 TBI.

For fuel pressure, it is fairly simple I spliced mine in after the fuel filter which worked great on my truck. I used Auto Meter 2246 and Rob already has it setup with correct parameters in EBL. I...
Forum: Power Adders
02-02-2014, 07:41 PM
Replies: 85
Views: 14,106
Posted By Cadride

Re: Almost done with SC install on 355 with 454 TBI.

To see how my timing compares to others - I am running about 31 under full boost. I attached my timing tables and a snapshot of a spreadsheet I put together to determine the actual. I fought a false...
Forum: Power Adders
02-01-2014, 06:43 PM
Replies: 85
Views: 14,106
Posted By Cadride

Re: Almost done with SC install on 355 with 454 TBI.

You spoke of possibly doing a water/meth injection on your setup. I have also been considering it especially if I increase boost.

With several great resources on this thread figured I would ask...
Forum: Power Adders
01-29-2014, 11:56 PM
Replies: 85
Views: 14,106
Posted By Cadride

Re: Almost done with SC install on 355 with 454 TBI.

I may have missed this, but what kind of fuel pressure are you running under full boost? I am over 45 psi. Do you have a fuel pressure gauge going into your EBL? I am running a similar but different...
Forum: TBI
01-28-2014, 11:59 AM
Replies: 48
Views: 5,336
Posted By Cadride

Re: 454 tbi

My 7.4 TBI has the flat IAC connector, I think it is off of a 93-94, but I could be wrong. I have an extra adapter (square to flat) from when upgraded my TB. I had to cut the wires to switch a couple...
Forum: DIY PROM
01-08-2014, 03:31 PM
Replies: 5,155
Views: 636,499
Posted By Cadride

Re: Tuning with the EBL

Ya I know I stopped driving mine few months ago. This is a great time to research different topics to your build. Since this is an older injection system most topics have already been covered. There...
Forum: DFI and ECM
11-14-2013, 12:02 AM
Replies: 7
Views: 1,437
Posted By Cadride

From my experience I would spend the money for...

From my experience I would spend the money for the EBL Flash at dynamicefi.com and get your self a WB gauge it will make tuning a lot easier. I started out doing mail order and have ended up with EBL...
Forum: TBI
11-05-2013, 06:20 AM
Replies: 53
Views: 14,057
Posted By Cadride

Re: EBL controlled E85 build

I just tried to switch my truck over to E85, but I couldn't keep enough fuel at WOT. I still have some E85 in the tank as this is not my daily driver; I was also having idle stalling and on my last...
Forum: TBI
10-28-2013, 09:45 PM
Replies: 8
Views: 1,193
Posted By Cadride

I would go with good stock gm distributor and...

I would go with good stock gm distributor and ignition module upgraded coil and plug wires. I run TBI through a Whipple SC, completely upgraded setup pushing 400-500 hp and have no issues with...
Forum: DFI and ECM
10-25-2013, 11:31 AM
Replies: 7
Views: 1,774
Posted By Cadride

Re: False Knock Issue Whipple 5.7

Thanks Rob, as we spoke in email. Had a few contributors to false knock.
Aftermarket Cats were junk and the core was loose in side of the can
Couple small header leaks between the head and the...
Forum: DIY PROM
10-25-2013, 11:11 AM
Replies: 3
Views: 2,165
Posted By Cadride

Re: 4l60e Tuning

Thanks for the input Rob, I did not find any posts from Dimented24x7 on 4l60e, but I have made considerable progress with on the tune; by trying different setting and many google searches.
Forum: Power Adders
10-21-2013, 12:20 PM
Replies: 8
Views: 4,218
Posted By Cadride

Re: Supercharger Cam Selection

Thanks for the input. I ended up going with a Mike Jones Custom Cam .544 lift 216/228 dur @.050, LSA 116. Over all very happy with the cam currently at 5 psi and feels stronger than ever. Plan to...
Forum: DIY PROM
10-20-2013, 07:54 PM
Replies: 3
Views: 2,165
Posted By Cadride

4l60e Tuning

Looking to get some 4l60e tuning opinions; and hopefully a thread that can be referenced in the future as a point of reference for tuning. This is my first time tuning a transmission so if you see...
Forum: DFI and ECM
09-24-2013, 08:49 AM
Replies: 7
Views: 1,774
Posted By Cadride

Re: False Knock Issue Whipple 5.7

I got the fitting installed and it did help, but did not solve the problem completely. One thing that I did notice is that my SA shoot up to 88 - 89 while under boost. The max SA is set to 32. The...
Forum: DFI and ECM
09-23-2013, 11:28 AM
Replies: 7
Views: 1,774
Posted By Cadride

Re: False Knock Issue Whipple 5.7

When I changed the knock sensor out I made sure to use plenty of teflon tape and I used a short ratchet and tried to only tighten it to snug.

Do you think a brass fitting would desensitize it to...
Forum: DFI and ECM
09-23-2013, 10:04 AM
Replies: 7
Views: 1,774
Posted By Cadride

False Knock Issue Whipple 5.7

Hey guys looking for anyone with experience with false knock issues. I have a 94 5.7 TBI with 2.3 Whipple, 195 AFR heads, roller cam, hydraulic lifters, EBL. More specs...
Forum: DIY PROM
09-20-2013, 11:40 PM
Replies: 2
Views: 1,394
Posted By Cadride

Re: Surging Idle EBL Whipple TBI

Rob thanks for the help. Makes a big difference to go back and smooth out the VE table after doing several learns. Between smoothing out the VE table and playing around with the IAC it idles a lot...
Forum: DIY PROM
09-14-2013, 02:44 PM
Replies: 2
Views: 1,394
Posted By Cadride

Surging Idle EBL Whipple TBI

Hey guys I have done quite a bit of research and gotten help from more experienced tuners, but continuing to have some small issues. I am to point that I have a decent idle at some points and pretty...
Forum: DIY PROM
09-05-2013, 11:09 AM
Replies: 5,155
Views: 636,499
Posted By Cadride

Re: Tuning with the EBL

What do I need to change in the $0D mask PCM 7427 to get the TCC to lock up when combined with the Flash EBL? I have wired the EBL ECM and 7427 PCM to Bob's recommendations with the engine coolant...
Forum: Power Adders
05-30-2013, 02:09 PM
Replies: 8
Views: 4,218
Posted By Cadride

Re: Supercharger Cam Selection

Slowly getting me engine together should get short block back from machine shop next week, I did get feedback from Comp Cams, and Crane Cams; which both of them said to stick with my current cam, as...
Forum: Engine/Drivetrain/Suspension Wanted
04-23-2013, 06:19 PM
Replies: 4
Views: 1,123
Posted By Cadride

Re: Dynamic EFI EBL Flash Switcher WTB

I was wondering if you happened to find any one that had the Flash Switcher available; with hopes that you found multiple people with them?
Forum: DIY PROM
04-12-2013, 09:17 AM
Replies: 26
Views: 4,494
Posted By Cadride

Re: EBL -IAT wiring

Thanks Rob
That's what I was hopping, I was a little afraid that the sensor wouldn't react to the temp changes from the SC effectivly.

Little off topic; for ebl flash would you recommend any...
Forum: DIY PROM
04-12-2013, 06:03 AM
Replies: 26
Views: 4,494
Posted By Cadride

Re: EBL -IAT wiring

Trying to resurrect an old post, instead of stating a new one. I was wondering on the subject of EBL, IAT and best location to put the IAT sensor on a Whipple SCed 5.7 TBI engine? I see many...
Forum: Power Adders
03-30-2013, 12:31 PM
Replies: 8
Views: 4,218
Posted By Cadride

Re: Supercharger Cam Selection

Cam recommended by Lutani for the build I have today is part# 20080721 Advertised Duration (Int/Exh): 270/278 Duration @ .050 (Int/Exh): 221/229 Gross Valve Lift (Int/Exh): .515/.530 LSA 112

Or...
Forum: Power Adders
03-30-2013, 12:21 PM
Replies: 8
Views: 4,218
Posted By Cadride

Re: Supercharger Cam Selection

Current Cam is a 112 LSA.

TraviZ is that a custom grind or does it have a part number so I can look up all the specs.
Forum: Power Adders
03-30-2013, 11:26 AM
Replies: 8
Views: 4,218
Posted By Cadride

Supercharger Cam Selection

Looking for to get some input on who makes the best cams for superchargers. There are so many options and hopping to find a cam grinder that has hands on experience with TBI's and Whipple's would be...
Forum: Power Adders
03-30-2013, 10:24 AM
Replies: 6
Views: 748
Posted By Cadride

Re: Head Selection for Whipple SC

Thanks guys for the input. Ordered a set of AFR 195 had to stick with them for emissions crap. They should be Wednesday can't wait.
Forum: Power Adders
03-26-2013, 10:12 PM
Replies: 6
Views: 748
Posted By Cadride

Re: Head Selection for Whipple SC

Orr89 your info intrigued me to look at your ride. All I can say is amazing and BA. What dynamic CR are you running with 14 psi and seeing that you are running the AFR 195 and got that kind of time...
Forum: Power Adders
03-26-2013, 09:58 PM
Replies: 6
Views: 748
Posted By Cadride

Re: Head Selection for Whipple SC

Thanks for the input. Planning on going with bigger chamber and going with flattops. One thing that has me going back to the 195cc runner is with my last setup using vortec heads I was able to get...
Forum: Power Adders
03-26-2013, 08:51 PM
Replies: 6
Views: 748
Posted By Cadride

Head Selection for Whipple SC

Guys and Gals would like to get some opinions on what is the best size of head to go with for a SC. I have a 355, 2.3 Whipple @ 10psi boost, 750 cfm 454 TBI bored to 54mm ports, Longtube headers 2...
Forum: Engine/Drivetrain/Suspension Parts for Sale
03-18-2013, 04:46 PM
Replies: 0
Views: 313
Posted By Cadride

WTB EBL Flash Selector

I am interested in purchasing an EBL Flash Selector if someone has one laying around that they want to get rid of?

Please PM if have one available.

Thanks,
Forum: DIY PROM
11-19-2012, 08:40 PM
Replies: 26
Views: 8,524
Posted By Cadride

Re: ebl flash vs ebl p4

I was hoping to run the EBL P4 on my TBI [Current PCM 16197427] with a Whipple SC where I wouldn't think that independent injector firing would be necessary; is this correct? I would like to use the...
Forum: Engine/Drivetrain/Suspension Parts for Sale
11-15-2012, 07:38 PM
Replies: 1
Views: 824
Posted By Cadride

Re: RBOBS FLASH EBL

Do you happen to still have the EBL for sale.

Thanks,
Forum: TBI
11-04-2012, 12:27 PM
Replies: 11
Views: 5,573
Posted By Cadride

Re: EBL and a 4l60E trans

Thanks Rob for the clarification helps, on making transmission upgrade decision.
Forum: TBI
11-04-2012, 09:40 AM
Replies: 11
Views: 5,573
Posted By Cadride

Re: EBL and a 4l60E trans

To use an EBL Flash ECM in a truck with an E transmission the stock PCM remains in place. It stays to run the transmission. Another set of ECM harness connectors are added to the stock harness. Power...
Showing results 1 to 44 of 44


 
Forum Jump


All times are GMT -5. The time now is 04:26 PM.