Third Generation F-Body Message Boards

Search: Posts Made By: CANROC85
Showing results 1 to 17 of 17
Search took 0.04 seconds.
Forum: Canadian Region
08-21-2013, 08:42 AM
Replies: 5
Views: 1,567
Posted By CANROC85

Stolen 1985 IrocZ Black London Ontario

Woke up this morning to someone peeling out across my front lawn in my camaro. If everyone could keeps eyes peeled for it. Black no Iroc stripes, one broken hood louver, 4 inch exhaust magniflow race...
Forum: Exhaust
12-30-2012, 08:44 AM
Replies: 28
Views: 6,422
Posted By CANROC85

Re: Dyno XFI280 385

Thanks the intake is an rpm air gap.
Forum: Exhaust
10-12-2012, 05:12 PM
Replies: 28
Views: 6,422
Posted By CANROC85

Re: Dyno XFI280 385

Orr, Mike Jones specked a cam how do you think it would work?
Part# HR73389-74365-110
284/288 @.006"
234/240 @.050"
.389"/.365" Lobe Lift
110 LSA
My HP estimates are always on the low side, but...
Forum: Exhaust
09-12-2012, 09:42 PM
Replies: 28
Views: 6,422
Posted By CANROC85

Re: Dyno XFI280 385

I have comp retro t bar lifters 853-16.
Might be worth a try.
Forum: Exhaust
09-12-2012, 06:28 PM
Replies: 28
Views: 6,422
Posted By CANROC85

Re: Dyno XFI280 385

Orr I was wondering what you think of running 1.7 roller rockers as the gentleman suggested on speed talk ?
Forum: Canadian Region
08-26-2012, 09:59 AM
Replies: 0
Views: 611
Posted By CANROC85

SLP 1 3/4 inch Headers with air tubes

I would like to sell my headers, will try on Canadian site first before I post on the US site.Thks $400.00
Forum: Exhaust
08-21-2012, 11:36 AM
Replies: 28
Views: 6,422
Posted By CANROC85

Re: Dyno XFI280 385

I also wondered what you think about a custom cam similar to the xfi 280 but getting the lift up just over 600 maybe 610?
Forum: Exhaust
08-21-2012, 11:33 AM
Replies: 28
Views: 6,422
Posted By CANROC85

Re: Dyno XFI280 385

I figured that the 3 inch section must be causing some back pressure at that power level. 3 inches only flows 812 cfm 540hsp would be 1188 cfm (2.2 cfm/hsp) just not sure how much it would be.Car...
Forum: Exhaust
08-20-2012, 04:57 PM
Replies: 28
Views: 6,422
Posted By CANROC85

Re: Dyno XFI280 385

Its a 385 afr 195 comps (1095), rpm airgap, prosystems carb, xfi 280, crowler roller rockers 1.6, eagle forged crank,mahle pistons, Thats about it with the new exhaust stainless works longtube 2.5...
Forum: Exhaust
08-20-2012, 04:38 PM
Replies: 28
Views: 6,422
Posted By CANROC85

Re: Dyno XFI280 385

Thanks I hope to break into 120's.
Forum: Exhaust
08-19-2012, 08:08 PM
Replies: 28
Views: 6,422
Posted By CANROC85

Re: Dyno XFI280 385

Last year did one trip to drag strip et was 12.54 some pretty poor launches and 115 mph. That was before I did the first dyno which the first run was 380 to the wheels so hopeful for some good mph...
Forum: Exhaust
08-19-2012, 08:03 PM
Replies: 28
Views: 6,422
Posted By CANROC85

Re: Dyno XFI280 385

Thanks
Forum: Exhaust
08-19-2012, 08:03 PM
Replies: 28
Views: 6,422
Posted By CANROC85

Re: Dyno XFI280 385

Dynojet the graph shows my before and after the exhaust work both done on the same Dyno.
Forum: Exhaust
08-18-2012, 12:14 PM
Replies: 28
Views: 6,422
Posted By CANROC85

Dyno XFI280 385

I just wanted to share my recent dyno results and maybe show the difference the new exhaust made.I had an SLP sysytem 1 3/4 header dual cat system, it was good enough to put 415 hrsp @5600 and 441...
Forum: Exhaust
11-26-2011, 02:34 PM
Replies: 0
Views: 504
Posted By CANROC85

Hawkes SBC LT and offroad Y pipe?

https://02b9194.netsolstores.com/hawkscamarofirebird82-92sbcstainlesslongtubeheaderswithoffroady-pipe.aspx

Has anyone tried these out? I have a t56 swap done at Hawkes so I have the cross member...
Forum: Exhaust
11-19-2011, 04:42 PM
Replies: 24
Views: 3,109
Posted By CANROC85

Re: Fastest pass thru the mufflers

I have an 85 Iroc Z with a 385 afr 195 comp eliminators the same xfi 280 comps cam.T56 The exhaust is an slp dual cat system 1.75 headers to 2.25 Y to a 3 " cat back the muffler is a ? as the slp...
Forum: Sponsored Vendors
10-25-2011, 06:29 PM
Replies: 2
Views: 2,000
Posted By CANROC85

Re: 10% OFF Moser 12 bolt and 9 inch rear ends!!!

Steven is this deal still available?
Showing results 1 to 17 of 17


 
Forum Jump


All times are GMT -5. The time now is 09:13 PM.