FueledSoul

iTrader: (18)

Thanks

Thanks Anything you put work and time into will turn out nice sometimes its more about having patience

updating right now

The one your looking for is http://www.summitracing.com/parts/MCH-22021-09/ if your running a belt driving water pump

yea i got rid of the bulkhead, headlight wires etc all post a pic shortly showing where i routed them.

Thanks

FueledSoul

iTrader: (18)

So after getting the engine harness done it was time to start on the board i used a sheet of 14ga aluminum and had drawn up some dimension and had a friend brake it since i don't have a brake. started with the fuse blocks and relays. i decided i didn't need the painless anymore since i already this far and we have been redoing the entire cars wiring anyway.

FueledSoul

iTrader: (18)

FueledSoul

iTrader: (18)

I started to finish painting the firewall and the rest of the inside. i also decided not to block off or weld a plate in place of the fresh air flap, instead i utilized it for a pressure relief to keep my gaskets from blowing out when i shut the doors or hatch. i would have left the vacuum diaphragm but it ended up interfering with the fuse board i had made up so i took it out and ran a spring.

FueledSoul

iTrader: (18)

I forgot to add to when i was coming up with the board i also wanted to bolt my msd to it so i had it wrap in. i also finished making a fibber glass excess panel for my tranny lines.

FueledSoul

iTrader: (18)

Wires still look messy but it will be better looking then any factory 80's wiring. Heres how i ran the headlight etc wires.

FueledSoul

iTrader: (18)

I got it running this summer but had some AFR issues which later turned out to be dirt in the carb i completely rebuilt it with in the last month also picked up a ultrasonic cleaner which help clean it all up even all orifices and cut rebuilding times down. i turned the fuel pump on and had gas from the front lines pumping into a shop rag and i got a lot of particles in the rag i don't know yet if its in just the lines that have stuff in them or somethings going on in the tank so im just going to cycle the fuel and add new gas and see if i still get anything coming out, im running a factory in-line fuel filter too so will see.

I still have to make a radiator hose, brackets for the carb and a braided kick down, finish the radiator top plate and im still stuck on what to do brakes I.E booster and master, but. . .

For your entertainment heres some videos
Note: The video and sound isn't greatest quality.

noboostnogo

iTrader: (4)

wow what a wire tuck!!!! awsome job




im just curious to know how you are distributing your + power. I cant seem to make it look nice. Is that thick black wire your positive from the battery or starter?

Keep up the amazing work.

FlamedROC

good to see you got it running!

1bad91Z

iTrader: (1)

Since you have allready come this far with your build, I would recommend using a pre-fabbed locking metal access panel (hinged with a latch) for your trans line access.

Summit and Jegs carry them in stock....

FueledSoul

iTrader: (18)

i move the bat to the rear of the car i have a main power wire going to the front of that panel its just not hooked up in that pic, the one you see goes to the starter. thanks



its already cut and the fibber glass one was molded to that area fits perfact, just going to used RTV it hold it in place and keep it sealed. never see it undercarpet

Curtisyz54

iTrader: (5)

Looking great man, I also shaved my firewall, and smooted out alot and filled all holes.






Close up

Sonymaster20

iTrader: (3)

Nice job curtiszyz How old are you again? arent you 17? Great work

Curtisyz54

iTrader: (5)

Thanks, and yes I am.

stage20

iTrader: (3)

dont know how i missed this thread.
pretty slick stuff!
any more progress on your transmission lines cover?

Dustytrix

iTrader: (3)

LOL and I thought I was making progress, great looking bays, both of you.

FueledSoul

iTrader: (18)

Thanks. yours looks nice! too. what color is that?

FueledSoul

iTrader: (18)

the covers done i just needed to run a bead rtv around it and snap it in place

Curtisyz54

iTrader: (5)

Thanks! Its called Deep Water Pearl. It is used on the 09 Challengers and what not. Its a Chrysler color.

noboostnogo

iTrader: (4)

any updates?

FueledSoul

iTrader: (18)

Well i finally decided on what to run for a brake assist.

Brakes:
i bought a LT1 booster and LS1 master cylinder. i just test fitted them on the car. the booster tucks closer to the fire wall and its appearance is much cleaner, i still have to prep it and put on some color, im painting it the same color as the car so it will blend in with the bay a bit more. i will use the stock prop valve with the ls1 master at least that's the plan. the master cylinder is much smaller and more compacted then the 3rdgen master so all in all im much happier plus i gained some brake performance going with a 1" bore ls1 master cylinder.

Carb:
I was having problems with the flimsy crab bracket, im going to order a bracket from loker, i did pick up a braided stainless steel TV cable since its the only one that can be used with that bracket.

Im also going to have to add a fuel fillter close to the carb, i already have one thats inline under the car but im picking up some junk in the carb which caused some fuel problems and flooding i rebuilt the carb entirety a few months back so its all ready to go for round 2. so i might have to re-do some lines and run things a bit differently now.

Other:
I have to paint the top radiator plate and bolt that in, i have to find some clips for the hood release. i still have to mount the 4thgen washer bottle and then find a place to bolt the aftermarket over flow and some other miscellaneous stuff. engine related i also have to make a y-pipe and hook up my exhaust system. then im pretty much done other then doing some small detail work and touch ups and a wash.

Oh and im about 75% done with wiring up the whole entire car thanks to my dad

t-top havoc

iTrader: (3)

Good to hear from ya FueledSoul!!!
Interesting use for brake booster & master cylinder....

Amazing work...Thanks for adding to inspiration...

Iroc-Dennis

FueledSoul i have send you a PM

dennis

The Project

iTrader: (6)

Cool idea

noboostnogo

iTrader: (4)

we need pictures lol
hows the wiring coming along?

FueledSoul

iTrader: (18)

Thanks

PM sent back






If your talking about the brake setup i might have time to take some comparison pics and post them tomorrow. still haven't got any of it hooked up on the car yet. as far as wiring we have to wire in the door locks, power windows, hatch pull down and wires for the curiosity lights. then its all done for the most part but we'll still have to test everything before i loom it.

FueledSoul

iTrader: (18)

Heres some pics

FueledSoul

iTrader: (18)

4thgen and 3rdgen booster compare

FueledSoul

iTrader: (18)

LS1 master with 3rdgen prob valve

I H8 WWD

iTrader: (5)

Definitely remembering this when I clean out my bay and do my brake setup. Awesome comparison.

Gibson27

iTrader: (1)

Have you considered hydroboost? Alot smaller than that bulky vacuum booster.

I H8 WWD

iTrader: (5)

Something like this, in which they have a bolt in application for us, gets rid of the big ole' brake booster
http://www.hydratechbraking.com/GM_3rdgenF_Body.html

Gibson27

iTrader: (1)

or even a hydroboost off a astrovan for the budget minded. Eventually I'll go that route when the engine bay is ready for painting and such.

FueledSoul

iTrader: (18)

Iv looked into running hydro-boost, pass. iv looked into everything. . . over a year this is what i ended up with its cheap and better looking then the 3rdgen master and booster. i would love to dump the booster and run manual brakes and really clean up the bay but this is going to be driven on the street

stroker_SS

Good job, you've inspired me.

FueledSoul

iTrader: (18)

thanks

FueledSoul

iTrader: (18)

I worked on the prop valve tonight cleaned it put it back together and semi polished it. . .

camarozz383

iTrader: (2)

I'm at the same thing right now, nice work man!!

Duane's 91 Z/28

iTrader: (1)

Wow its been a long time since I've been to this thread and wow, what an inspiration for me to want to at least work on my wiring harness and fix some of the wires that have been cut and splices before I got the car. Great job!!

Awesome-X

So how goes the progress Soul, we haven't heard from you in here for almost a year!

built91Z28

I'm glad I looked at this thread. I think I need a new booster anyways and really wanted one that sat just a little farther back than the stock one. The tip of my master hits my Spohn strut mount and only lets me set the camber so far in.

Daytona_83

Wow, great thread! I was looking for how-to's about cleaning the engine bay up...but I don't think I'm ready to rip the motor out and respray it just yet. LoL! I just wanted to clean up the existing bay as there is so much grease and crap, and it's a white car, so it's filthy. Someday I hope to have an engine bay as clean as yours. Great job!

Awesome-X

How did the car turn out? Did you get it finished?

FueledSoul

iTrader: (18)

Thanks for all the comments and complements guys! Progress has been some what slow on the bay, iv been busy busting out the body panels, here's whats going on with that
https://www.thirdgen.org/forums/auto...ml#post4647632

Here is some pics of the booster and other parts i installed into the bay.
its not much.

Drilled out and mounted my secondary fan control box



Got some peaces in primmer painted

FueledSoul

iTrader: (18)

Here is some crappy camera phone pics, sorry for the quality, hope to get some better ones when im done with everything

Awesome-X

Ah I didn't know you'd started another thread, I like your door handles lol. The engine bay looks amazing, and I really like that color.

FueledSoul

iTrader: (18)

thanks man

Daytona_83

Sweet man, I'll have to come down to the cities sometime and check the car out when it's done...I'm just going through your body work thread right now.

Camaroguy6984

iTrader: (2)

WOW!

Scorpner

iTrader: (4)

That looks great!