i need ideas and pics on how to make a nos blow shieald
03-31-2008, 08:56 PM
#2
Member
Join Date: Jul 2005
Location: upland, ca
Posts: 235
Likes: 0
Received 0 Likes
on
0 Posts
Re: i need ideas and pics on how to make a nos blow shieald
never heard of a blow sheild. you do need a tube connected to the blow off on the valve that vents outside of the car if the bottle is mounted in the passenger compartment.
04-03-2008, 09:55 PM
#5
Junior Member
Thread Starter
Join Date: Jul 2007
Posts: 15
Likes: 0
Received 0 Likes
on
0 Posts
Re: i need ideas and pics on how to make a nos blow shieald
i was told i need one i guess its like a wall between the bottle and the engine compartment
----------
not the engine compartment the passenger compartment
----------
not the engine compartment the passenger compartment
Last edited by badass91; 04-03-2008 at 09:55 PM. Reason: Automerged Doublepost
04-04-2008, 11:08 AM
#7
Member
Join Date: Mar 2006
Location: FH/Waterford/Port Huron, MI
Posts: 297
Likes: 0
Received 0 Likes
on
0 Posts
Car: 2 camaros 1 trailblazer SS
Engine: 346twinturbo, 383tpi
Transmission: t56 and 700r4
Axle/Gears: 3:46 4:11
Re: i need ideas and pics on how to make a nos blow shieald
Nos can be mounted in the car next to the driver without any type of firewall or shield. They are right about the blow down tube. Due you mean a burst panel? Not needed for track.
Trending Topics
04-04-2008, 10:12 PM
#8
Junior Member
Thread Starter
Join Date: Jul 2007
Posts: 15
Likes: 0
Received 0 Likes
on
0 Posts
Re: i need ideas and pics on how to make a nos blow shieald
ya a burst panel thanks so i dont need one thanks alot guys all i need is the blow down tube? also do i have to weld the bottle bracketts or nut and bolt ?
04-05-2008, 05:49 AM
#9
Supreme Member
Join Date: Mar 2001
Location: Portland, OR www.cascadecrew.org
Posts: 6,577
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1990 Camaro RS
Engine: Juiced 5.0 TBI - 300rwhp
Transmission: T5
Axle/Gears: 3.42 Eaton Posi, 10 Bolt
Re: i need ideas and pics on how to make a nos blow shieald
Some of it will depend on what bottle you have. Which kit did you buy, and what bottle does it have?
You need something like this....
http://store.summitracing.com/partde...5&autoview=sku
then you need a blow-down tube. The tube attaches to that fitting, and the tube must vent to the outside of the vehicle.
http://store.summitracing.com/partde...5&autoview=sku
You can use can bolt the bottle mounts down that is fine, you just have to make sure they are "secure". When I tech my car, they usualy just pull/push on it a bit, and make sure it won't go anywhere.
Here is how I have mine mounted, I drilled a hole in the pastic behind the seatbelt, and then the blowdown tube exits the car through the spare tire well. I had to do a little bit of bending on the tube to make it fit like I wanted, and I cut about 5" off the tube so it didn't hang down that far.
Hope that helps.
--John
You need something like this....
http://store.summitracing.com/partde...5&autoview=sku
then you need a blow-down tube. The tube attaches to that fitting, and the tube must vent to the outside of the vehicle.
http://store.summitracing.com/partde...5&autoview=sku
You can use can bolt the bottle mounts down that is fine, you just have to make sure they are "secure". When I tech my car, they usualy just pull/push on it a bit, and make sure it won't go anywhere.
Here is how I have mine mounted, I drilled a hole in the pastic behind the seatbelt, and then the blowdown tube exits the car through the spare tire well. I had to do a little bit of bending on the tube to make it fit like I wanted, and I cut about 5" off the tube so it didn't hang down that far.
Hope that helps.
--John
Thread
Thread Starter
Forum
Replies
Last Post
Ghettobird52
Tech / General Engine
15
12-29-2023 08:23 AM
1992 Trans Am
History / Originality
27
05-10-2023 07:19 PM
92firebirdchris
Exterior Parts for Sale
0
08-14-2015 11:56 AM
