claus290373

Hello where i live my old car 1989 trans am 5.7 dont need a cat to pass inspection and when the cat went bad i replaced it with a pipe. I dont want to remove the airpump for now and have closed the airpipe where it normal goes to the cat is that okay or ????

thanks claus

I H8 WWD

iTrader: (5)

I see claus and I think of the Fish from American Dad. Anyway, delete that bi...big piece of weight. I bought my delete pulley from Hawks years ago, when it was about $45. Almost double now, but here you go. Hawks Smog Delete Pulley
TPIParts has it for $84.

DynoDave43

iTrader: (11)

$69.25

http://www.ebay.com/itm/131034924958...l2649#shpCntId

While some ebayers won't ship overseas, this one lists Denmark as a location they will ship to.

I H8 WWD

iTrader: (5)

This is fun lol.
$48

DynoDave43

iTrader: (11)

Nothing wrong with finding the best price.

This one you linked to says A/C delete. I think the OP is after the air pump version. I'm assuming they are not interchangeable?

I H8 WWD

iTrader: (5)

Correct, but the part number is for the Smog Delete Pulley. Plus the picture shows the 2bolt design of the smog delete pulley as well. It's just a typo. It's why I always search Part#'s.

DynoDave43

iTrader: (11)

Good catch!

1986 iroc z28

just take the air pump off and use a different belt, no need for a delete pulley

slowsi

iTrader: (2)

do you happen to know a belt number?

chevyredneck8

iTrader: (4)

Y does everyone buy a pulley you can remove it and install a smaller belt if its serpentine. I've been running this setup for years its cheaper and lighter weight!

I'll have to check my recites I just bought on I think the replacement was a 70. Most auto parts stores will let you buy multiple and bring back what you don't need.

gallaire

my new smog pump pulley from hawks is wobbling a little bit . wat a piece tired of this ****

gsmarcano

you will need a 96.8", 6 rib belt and look up the re-routing on this site.

chevyredneck8

iTrader: (4)

I would bypass it with the shorter belt as suggested I've been running this setup for years with zero problems

gallaire

I wasted 100 bucks lol

dmccain

iTrader: (2)

I bought a 96.8 in belt just like I did on my last TPI engine and removed smog pump and the belt was too dang long for the TBI engine.. I put it back on and will probably get the smog delete pulley from Amazon or get a string around it and measure like I should have first.

3rdgenmaro

iTrader: (9)

You sure you got the right belt and have it routed right? Works fine on my 91 TBI.

dmccain

iTrader: (2)

Im going to measure the belt myself it was listed 96.5 or 96.8 in if I can remember but you know things get mixed up in packaging sometimes. As far as the route yea I had a diagram and checked it over good. I was in a hurry and didn't physically measure the belt but im sure they will make good on it and trade me another if it wasn't what I ordered.

3rdgenmaro

iTrader: (9)

You don't have underdrive pulleys do you?

Ty92Z

iTrader: (11)

Serpentine setup is the same for tpi and tbi. I bought the 968k6 and used the alternate routing. Worked great.

dmccain

iTrader: (2)

I just went ahead and ordered the $48 smog delete pulley from Amazon. It does look a little cleaner with it instead of the hole it leaves when you take out the smog pump all together imo.