New to the board
#1
Junior Member
Thread Starter
Join Date: Jan 2014
Location: Long Island, NY
Posts: 68
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1987 Transam
Engine: LT1 conversion
Transmission: Rebuilt 700r4 w/2400 stall
Axle/Gears: 373
New to the board
Hey guys I been around here for a long time but just recently joined up. I had my 1987 Transam since 1995 and did the engine and interior over in 2001 spending well over $20,000. Since then its basically been garaged and maybe driven 3000 miles at best due to marriage/kids. Just recently registered and insured it again so I can finally start to truly drive and enjoy this beast again. Just ordered 4 new tires and still have 4 brand new 16x8 GTA black honeycomb rims I got from Classic Industries back in 2000 still in the box. Here is what has been done so far: (any comments/suggestions/criticisms are all appreciated)
1994 LT-1 engine bored+honed .30
Air Flow Research Heads 190 LT-1 reverse cool 74cc
Sanderson Street Rod Headers- small block Chevy ceramic coated
MSD ignition and coil
Cold air induction kit
Fuel pressure regulator
Moroso Valve cover gaskets
Pro Torque converter 10.5' 700r4 30 spline
Rebuilt 700r4 Transmission w/ shift kit
Comp cam LT1 xr269hr-12
BBR 52mm throttle body
160* thermostat
Hotchkis panhard rod bar
Crane Gold Race Pro Series Rockers 11755-16
Rocker Arms, Stud Mount, Full Roller, Aluminum, 1.6 Ratio, Fits 7/16 in. Stud,
3 inch custom exhaust
373 gears
H/P custom chip
SSM Subframe Connectors welded
Edlebrock Lower Trailing Arms
Edlebrock Strut Tower Brace
Koni rear shocks
Power stop slotted rotors
SSBC calipers
New GM power window motors and pull down hatch motor
GM ground deflector 12395557
1994 LT-1 engine bored+honed .30
Air Flow Research Heads 190 LT-1 reverse cool 74cc
Sanderson Street Rod Headers- small block Chevy ceramic coated
MSD ignition and coil
Cold air induction kit
Fuel pressure regulator
Moroso Valve cover gaskets
Pro Torque converter 10.5' 700r4 30 spline
Rebuilt 700r4 Transmission w/ shift kit
Comp cam LT1 xr269hr-12
BBR 52mm throttle body
160* thermostat
Hotchkis panhard rod bar
Crane Gold Race Pro Series Rockers 11755-16
Rocker Arms, Stud Mount, Full Roller, Aluminum, 1.6 Ratio, Fits 7/16 in. Stud,
3 inch custom exhaust
373 gears
H/P custom chip
SSM Subframe Connectors welded
Edlebrock Lower Trailing Arms
Edlebrock Strut Tower Brace
Koni rear shocks
Power stop slotted rotors
SSBC calipers
New GM power window motors and pull down hatch motor
GM ground deflector 12395557
#3
Junior Member
Thread Starter
Join Date: Jan 2014
Location: Long Island, NY
Posts: 68
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1987 Transam
Engine: LT1 conversion
Transmission: Rebuilt 700r4 w/2400 stall
Axle/Gears: 373
Re: New to the board
Thanks I wish it still looked like that though. That pic was from 2001. I gotta get in there and do some cleaning.
Thread
Thread Starter
Forum
Replies
Last Post
Linson
Auto Detailing and Appearance
12
10-01-2015 09:50 PM