UberFast

iTrader: (1)

Hey guys will the speed sensor that come with the 92 on the 5 speed work with my 700r4 that's going into the 92?

Tuned Performance

iTrader: (92)

http://tpiparts.net/inc/sdetail/7587

UberFast

iTrader: (1)

So what sensor were y'all talking about that I could use that was from a 92 but not the one you linked? I took it as I needed a factory 92 vss?

UberFast

iTrader: (1)

Also when I look up 92 speed sensors none of them pictured have gears on them. Is that supposed to be? Do I have to buy that separate?

Will one of these work with my 700r4 and the current wiring on the 92 I'm swapping into?

http://www.autopartswarehouse.com/se...score=7.565071

Tuned Performance

iTrader: (92)

Are you using the 86 700r4 ? If so it is cable drive and the vss in 86 is in the speedometer.
You would need the conversion vss, or swap the tail housing , and drive and driven gears to the later model design.

UberFast

iTrader: (1)

Yes it's from the 86. I see that it's cable drive but where does the cable run to? The back of the speedometer? With that conversion vss do I have to use my 86 cluster?

Tuned Performance

iTrader: (92)

The 92 speedometer will get its signal from the ecm pin b11.

UberFast

iTrader: (1)

OK but that vss conversion you linked says it mounts in between the tranny and speedo cable. Where would I run the other end of the speedo cable since the 92 speedometer is electronic?

Tuned Performance

iTrader: (92)

Stick a cap nut on it.

UberFast

iTrader: (1)

Ok so it won't be used at all. Thanks that's what I was trying to figure out.

UberFast

iTrader: (1)

Alright fellas I'm starting on swapping my shifter over to the 92. What's the best easiest thing to do? Bolt/weld a piece of sheet metal over the hole where the manual was? I guess ill have to cut a hole for the shift linkage too.

pats91rs3.1

hey there, I'm planning on doing a similar swap soon. I have 89 gta 350tpi i want to put in my 91 3.1 rs. I read about using the 91 v6 ecm if you reprogram and a 91-92 engine harness. Can I replace my v6 cluster with a v8 140mphcluster and be able to use all gauges? tranny is coming from the 89 due to it being behind a v8. sorry if im outta place posting here thanks

Tuned Performance

iTrader: (92)

The answer is yes, the 3.1 and 5.7 speed density use the sane ecm the 1227730. The only difference besides the engine wiring is the memcal itself.

UberFast

iTrader: (1)

Hey guys I just started laying the wire harness out on top of the engine before I drop it back into the car and have a couple questions.

I noticed that I have a 2 prong oil pressure switch located next to my distributor and I have a 3 prong pigtail for it. I'm assuming I need a 92 oil pressure switch for it to work? I'm also assuming that pigtail is the oil pressure switch based on pics I looked at on google. Can I simply leave that oil pressure switch where it's at and install the 92 switch above the oil filter?

Tuned Performance

iTrader: (92)

You can change the plug end to female spade. You will need to hook up the orange and grey wire polarity doesn't matter. the blue wire is for a gauge or idiot light.

UberFast

iTrader: (1)

Ok do I need to ground the blue wire? Will the oil pressure light stay on with it disconnected?

Tuned Performance

iTrader: (92)

If you have a idiot light it will come on when the blue wire gets grounded.

UberFast

iTrader: (1)

Which of these will I use? I don't have a blue wire that I see. Do I use the 2 heavier gauge wires that are on the outside? Middle is idiot light?

Tuned Performance

iTrader: (92)

I believe the heavier orange is the hot fused wire buyer your fender well. The other heavier wire goes to the fuel pump. I think the middle one is for the gauge/mil

UberFast

iTrader: (1)

what do i plug my o2 sensor up to? The o2 sensor i have just has a single metal prong i guess you'd say on the end of it. I've looked at some pics of o2 sensor pigtails but i dont see anything like that on mine.

Tuned Performance

iTrader: (92)

the o2 on the harness side is male, it is a few inches away from the cylinder head female gauge green wire. It drops down on the drivers side runs next to the oil pan and on top of the engine mount.

UberFast

iTrader: (1)

ok thanks. As for the cold start injector, i wont be using it anymore will I? Can i just leave it there?

Tuned Performance

iTrader: (92)

Yeh, just let it be, you can get a block off kit from hawks thirdgen if your worried about it leaking or cosmetics.

UberFast

iTrader: (1)

i think i'll just leave it there. Are the manifold/intake air temp sensors different between 86 and 92? That's another one i can't find a connector for, located under the throttle body.

UberFast

iTrader: (1)

Sorry i was looking at the wrong sensor. The sensor i was looking at is for the cold start injector i believe so that's why i can't find a pigtail.

Tuned Performance

iTrader: (92)

Lmao, there will be a Bosch timer switch on the rh front of the intake and the csi.

UberFast

iTrader: (1)

lol thanks. ok now i have two connectors that look identical except one is white and one is black, one of them goes to the knock sensor but not sure which one. Which one goes to the knock sensor and where does the other go?

Thanks for all your help by the way, i know i have a ton of questions lol

Tuned Performance

iTrader: (92)

The one with the blue wire I believe grey connecter is your knock sensor. The white connecter is the passengers side fan temp sensor.

UberFast

iTrader: (1)

alright sweet. I'm going to let my brain take a break for the rest of the night and pick up in the morning lol. I'm sure i'll have more questions but thanks again for all the help so far.

Tuned Performance

iTrader: (92)

Np, we only charge $10 per correct answer lmao

UberFast

iTrader: (1)

I guess that makes me your retirement plan lol

UberFast

iTrader: (1)

Ok so I'm onto the next obstacle. I believe the alternator pigtail is different on this harness as well. I think it's the alternator wires anyway, has heavier gauged red and black wires going to it and is also on the opposite side my alternator is on which was expected.. Is this as easy as cutting the pigtail off of my 86 harness and splicing it in place on my new harness?

UberFast

iTrader: (1)

This is the connector off the old harness

Tuned Performance

iTrader: (92)

Your right you will need to change the ends, the current harness is a cs alternator, the one on your engine is a Si .

Tuned Performance

iTrader: (92)

pretty much

UberFast

iTrader: (1)

Alright sweet I got that swapped. Now back to the knock sensor. You said the blue wire w/ grey connector is the ks and white connector is for the fan, well my white connector has a blue wire and the black connector has a grey wire. Which is which? Mine must be a little different.

Tuned Performance

iTrader: (92)

Than I remembered the connecter body colors back azz words. Blue wire knock sensor btw you need the 350 3.9K ohm ks and grey wire to the cylinder head temp switch.

UberFast

iTrader: (1)

I don't see anything here that looks like an o2 sensor connector. What does this go to?

Tuned Performance

iTrader: (92)

ac pressure switch on your receiver dryer. btw your knock sensor is acdelco 213-92 gm 1045649 .

UberFast

iTrader: (1)

My ks is standard series KS6T from rock auto. Did I get the right one? Also my cylinder head temp switch is different. Can I simply cut that connector off and splice a female spade connector? Or do I need a 92 cylinder head temp switch?

UberFast

iTrader: (1)

Do I use this at all or was this only for the 86?

Tuned Performance

iTrader: (92)

I though we coved that in post #69 ?

UberFast

iTrader: (1)

Earlier I was asking about the 2 prong part on bottom. I'm wanting to know about the single prong part on top now.

Tuned Performance

iTrader: (92)

That's for the center wire left over from the ops plug for a oil pressure gauge.

UberFast

iTrader: (1)

Oh ok so I need to plug that wire onto that prong and T off to an oil pressure gauge or would i run the wire straight to the oil pressure gauge and leave the prong unplugged?

Tuned Performance

iTrader: (92)

ou will need to double check c100 pinout for the differences but the center wire of the ops runs to the ip gauge if equipped if not it uses a mil. I can't recall the looks of the idiot light sender and the gauge it may work either way idk.

UberFast

iTrader: (1)

Ok ill check the pinouts. Also what does this little guy go to?

Tuned Performance

iTrader: (92)

I think that's the power wire for the hood light

UberFast

iTrader: (1)

ok i know there are some things on the engine that will no longer be used. ive read about most of them but what about the manifold air temp sensor located under the intake near the fpr? i don't have a connector that i see for it.

Tuned Performance

iTrader: (92)

The mat end is a weather pack 2 wire female bye the distributor . A pigtail gets used to attach the mat.