4" exhaust Gen 3 Camaro/Firebird
#1
Junior Member
Thread Starter
4" exhaust Gen 3 Camaro/Firebird
Mufflex 4" single exhaust with Magnaflow muffler. Comes with matching Y-Pipe for Hooker Super Comp Long Tube Headers 700$ OBO Also comes with muffler delete pipe ( not shown)
Last edited by 1badmaro; 06-17-2020 at 03:28 AM.
#2
Junior Member
Thread Starter
Re: 4" exhaust Gen 3 Camaro/Firebird
Also comes with muffler delete pipe
#4
Junior Member
Thread Starter
Re: 4" exhaust Gen 3 Camaro/Firebird
Yes. But I have a few others interested. If it falls through well work something out.
#7
Member
Join Date: Dec 2003
Location: wv
Posts: 489
Received 0 Likes
on
0 Posts
Car: 92 rs
Engine: 355 stealth ram, dart heads, S480
Transmission: 4L80E
Axle/Gears: 3.42
Re: 4" exhaust Gen 3 Camaro/Firebird
Just curious why you are selling it? I was looking at 4” exhaust. Haven’t heard many reviews
Trending Topics
#8
Junior Member
Thread Starter
Re: 4" exhaust Gen 3 Camaro/Firebird
going fender exit BBC. Heat wrap on muffler is because it was a street car with a factory tank with a sump. System fit awesome and sounded nasty behind a 355 with a solid roller.
#11
Junior Member
iTrader: (1)
Re: 4" exhaust Gen 3 Camaro/Firebird
Does that y pipe fit the Hooker Supercomp BBC headers for the third gen? Photo shows those headers.
Nevermind, I see you had it behind a SBC. Approx shipping to AZ?
Last edited by drdan1341; 05-24-2020 at 09:17 AM. Reason: Question answered
#12
Junior Member
Thread Starter
Re: 4" exhaust Gen 3 Camaro/Firebird
system is located in South Eastern PA 19152 as of now i'm trying to sell local shipping would be expensive and a pain to box up.
#13
Member
Join Date: Dec 2003
Location: wv
Posts: 489
Received 0 Likes
on
0 Posts
Car: 92 rs
Engine: 355 stealth ram, dart heads, S480
Transmission: 4L80E
Axle/Gears: 3.42
Re: 4" exhaust Gen 3 Camaro/Firebird
unfortinately philly is about a 5hr drive away for me. If you decide to just sell the catback and ship I might be interested. I have no use for the front half.
#14
Supreme Member
iTrader: (15)
Re: 4" exhaust Gen 3 Camaro/Firebird
Yea I'm out of the running. I bought a new Hawks sinister kit about 2 weeks ago and picked up a muffler to make my own. The Hawks kit uses all mufflex peices they just dont get the muffler and sell you it with a delete pipe. I will confirm for the OP that the overaxle pipe and the whole kit fits amazing... super impressed that they get it to clear the stock PHB support and it tucked up better than my 3" catback.
Good luck with the sale!
Good luck with the sale!
#15
Junior Member
Thread Starter
Re: 4" exhaust Gen 3 Camaro/Firebird
Bump price drop 700$ picked up
#16
Junior Member
Thread Starter
Re: 4" exhaust Gen 3 Camaro/Firebird
If anyone is interested make me an offer.
#17
Supreme Member
iTrader: (25)
Join Date: Sep 2005
Location: NJ
Posts: 1,816
Received 280 Likes
on
218 Posts
Car: 1987 IROC-Z
Engine: 406 on N20 w/ EFI
Transmission: P.B. 700R4
Axle/Gears: 12 bolt w/ 3.91
Re: 4" exhaust Gen 3 Camaro/Firebird
Wow, this would be an awesome upgrade that I will need to do once I do get the nitrous hooked up. I am in northern NJ but have family over by the phoenixville PA area
question, what size headers are on the car? I have the 1 3/4” dyno dons headers but I think I’ll need a 1 7/8 or 2”
primary tube setup for my 406 when the nitrous is setup.
im
holding off on the nitrous for a bit longer until
i get the car fully sorted out but it is almost there. Prior to exhaust I’ll also need a full set of street tires, so that’s where my money is going next. I’d also need headers to match. But I am interested in the exhaust if it doesn’t sell in a few months time though
question, what size headers are on the car? I have the 1 3/4” dyno dons headers but I think I’ll need a 1 7/8 or 2”
primary tube setup for my 406 when the nitrous is setup.
im
holding off on the nitrous for a bit longer until
i get the car fully sorted out but it is almost there. Prior to exhaust I’ll also need a full set of street tires, so that’s where my money is going next. I’d also need headers to match. But I am interested in the exhaust if it doesn’t sell in a few months time though
#18
Junior Member
Thread Starter
Re: 4" exhaust Gen 3 Camaro/Firebird
Wow, this would be an awesome upgrade that I will need to do once I do get the nitrous hooked up. I am in northern NJ but have family over by the phoenixville PA area
question, what size headers are on the car? I have the 1 3/4” dyno dons headers but I think I’ll need a 1 7/8 or 2”
primary tube setup for my 406 when the nitrous is setup.
im
holding off on the nitrous for a bit longer until
i get the car fully sorted out but it is almost there. Prior to exhaust I’ll also need a full set of street tires, so that’s where my money is going next. I’d also need headers to match. But I am interested in the exhaust if it doesn’t sell in a few months time though
question, what size headers are on the car? I have the 1 3/4” dyno dons headers but I think I’ll need a 1 7/8 or 2”
primary tube setup for my 406 when the nitrous is setup.
im
holding off on the nitrous for a bit longer until
i get the car fully sorted out but it is almost there. Prior to exhaust I’ll also need a full set of street tires, so that’s where my money is going next. I’d also need headers to match. But I am interested in the exhaust if it doesn’t sell in a few months time though
Thread
Thread Starter
Forum
Replies
Last Post
Bigdream
Engine/Drivetrain/Suspension Parts for Sale
8
07-11-2019 07:28 AM
85irocZ2819
Engine/Drivetrain/Suspension Parts for Sale
15
07-07-2019 05:43 AM