[PA] Vortec 350 sbc with 700r4
#1
Vortec 350 sbc with 700r4
I have a 350 small block chevy with a 700R4 trans out of my third gen camaro for sale. Motor is fresh, trans mileage unknown but good working order when pulled. Motor/trans only removed because I am going LS.
Motor:
350 SBC .030 over
2 bolt main, stock bottom end, 10:1 flat top pistons
062 GMPP vortec heads
Comp cam (have specs, will get later)
GMPP TBI vortec intake
TBI unit with larger injectors
Jegs high torque starter
Motor rebuild about 4 years ago, less than 5,000 mi since rebuild
No accessory drive or exhaust included
Trans:
700R4, unknow mileage
B&M shift kit
B&M 2400 stall converter
This setup put my 92 camaro 13.8's in the 1/4 mile at 100 mph. Estimated ~315-330 crank HP
Willing to sell just motor, just trans, or together for $1,300.
Located in philadephia suburbs zip 19428. Local pickup only
Motor:
350 SBC .030 over
2 bolt main, stock bottom end, 10:1 flat top pistons
062 GMPP vortec heads
Comp cam (have specs, will get later)
GMPP TBI vortec intake
TBI unit with larger injectors
Jegs high torque starter
Motor rebuild about 4 years ago, less than 5,000 mi since rebuild
No accessory drive or exhaust included
Trans:
700R4, unknow mileage
B&M shift kit
B&M 2400 stall converter
This setup put my 92 camaro 13.8's in the 1/4 mile at 100 mph. Estimated ~315-330 crank HP
Willing to sell just motor, just trans, or together for $1,300.
Located in philadephia suburbs zip 19428. Local pickup only
#2
TGO Supporter
Join Date: Jul 2001
Location: Cheyenne, Wyoming
Posts: 4,991
Likes: 0
Received 1 Like
on
1 Post
Car: 1992 B4C 1LE
Engine: Proaction 412, Accel singleplane
Transmission: built 700R4 w/custom converter
Axle/Gears: stock w/later 4th gen torsen pos
Re: Vortec 350 sbc with 700r4
I am very curious to know about the tune/ECM you used for this setup.
#7
TGO Supporter
Join Date: Jul 2001
Location: Cheyenne, Wyoming
Posts: 4,991
Likes: 0
Received 1 Like
on
1 Post
Car: 1992 B4C 1LE
Engine: Proaction 412, Accel singleplane
Transmission: built 700R4 w/custom converter
Axle/Gears: stock w/later 4th gen torsen pos
Re: Vortec 350 sbc with 700r4
I am curious about this as well ^^^
Also still very interested in what cam you ran. Inquiring minds want to know!
Also still very interested in what cam you ran. Inquiring minds want to know!
Trending Topics
#8
Re: Vortec 350 sbc with 700r4
I believe I had 68# injectors at 18psi. Yes, it was underfueled. Never got around to properly fueling it due to other projects. I'll see if I can dig up the cam card and post it.
I still have the GMPP manifold and TBI unit if anyone is interested. I sold the motor/trans without the intake setup.
I still have the GMPP manifold and TBI unit if anyone is interested. I sold the motor/trans without the intake setup.
Thread
Thread Starter
Forum
Replies
Last Post
TADailyDriver
Engine/Drivetrain/Suspension Parts for Sale
3
04-14-2018 08:07 AM
89RsPower!
Engine/Drivetrain/Suspension Parts for Sale
2
09-17-2011 11:22 PM
rx7 punk
Tech / General Engine
4
05-19-2007 08:26 PM