[Sold] Stealth Ram Setup w/ Extras (NON Vortec)
#1
Senior Member
Thread Starter
iTrader: (8)
Join Date: Jun 2009
Location: Peoria, AZ
Posts: 768
Likes: 0
Received 2 Likes
on
2 Posts
Car: 91 Z28, 2000 T/A
Engine: SBC 355, LS1
Transmission: T56, T56
Axle/Gears: 10bolt 3.73, 3.42
Stealth Ram Setup w/ Extras (NON Vortec)
Hey All,
I have a Holley Stealth Ram that I picked up off here a few months back.
Here is what the lot includes
- Stealth Ram upper and lower for standard SBC heads. it's a later casting with the inner bolt holes are drilled for 45* and 72* bolt holes.
- Holley Fuel Rails w/ crossover tube
- Kirban adjustable fuel pressure regulator
- Steel braided fuel lines with hose ends.
- 2/16" Autometer carbon fiber face fuel pressure gauge 0-100 psi
- All the -6 fitting necessary to connect the fuel pressure gauge and fuel lines from the rails, 14mm O ring and 16mm O ring to -6 to hook up to the factory hard lines.
- Thermostat housing
- Throttle cable bracket
- Factory 89-92 style TB modified to clear fuel rails with all sensors and the IAC housing (coolant tubes removed)
- Multiple barbed fitting to connect vacuum accessories, there is a T fitting under the center of the manifold that isn't pictured.
- Heater hose fitting, distributor hold down, CTS and IAT sensor included.
I am not really looking to seperate anything out. This is complete and ready to bolt on, throw your injectors in it and go. My rough guesstimate is $1000 to put everything here together new.
I'd like to get $650 Shipped in the US. I will split the shipping cost to Canada. Thanks for looking!
HSR Weiand Wieand Holly
I have a Holley Stealth Ram that I picked up off here a few months back.
Here is what the lot includes
- Stealth Ram upper and lower for standard SBC heads. it's a later casting with the inner bolt holes are drilled for 45* and 72* bolt holes.
- Holley Fuel Rails w/ crossover tube
- Kirban adjustable fuel pressure regulator
- Steel braided fuel lines with hose ends.
- 2/16" Autometer carbon fiber face fuel pressure gauge 0-100 psi
- All the -6 fitting necessary to connect the fuel pressure gauge and fuel lines from the rails, 14mm O ring and 16mm O ring to -6 to hook up to the factory hard lines.
- Thermostat housing
- Throttle cable bracket
- Factory 89-92 style TB modified to clear fuel rails with all sensors and the IAC housing (coolant tubes removed)
- Multiple barbed fitting to connect vacuum accessories, there is a T fitting under the center of the manifold that isn't pictured.
- Heater hose fitting, distributor hold down, CTS and IAT sensor included.
I am not really looking to seperate anything out. This is complete and ready to bolt on, throw your injectors in it and go. My rough guesstimate is $1000 to put everything here together new.
I'd like to get $650 Shipped in the US. I will split the shipping cost to Canada. Thanks for looking!
HSR Weiand Wieand Holly
Last edited by 3rd gen Will; 02-01-2013 at 03:21 PM.
#3
Junior Member
Join Date: Jul 2008
Location: Somerset NJ
Posts: 3
Likes: 0
Received 0 Likes
on
0 Posts
Re: Stealth Ram Setup w/ Extras (NON Vortec)
Stuff like this always pops up when I have no money! Don't hate me for trying......... Would you take $500 and I'll send you a UPS shipping label to use?
#5
Supreme Member
iTrader: (27)
Re: Stealth Ram Setup w/ Extras (NON Vortec)
Are you open for trades? I have a TON of stuff i'm trying to part with. I also do porting. I'd be willing to port something that you might have. Look up "Endgame Performance" on Facebook for everything I have for trades and portwork if you're interested.
#6
Senior Member
Thread Starter
iTrader: (8)
Join Date: Jun 2009
Location: Peoria, AZ
Posts: 768
Likes: 0
Received 2 Likes
on
2 Posts
Car: 91 Z28, 2000 T/A
Engine: SBC 355, LS1
Transmission: T56, T56
Axle/Gears: 10bolt 3.73, 3.42
Re: Stealth Ram Setup w/ Extras (NON Vortec)
Not likely, Sent you a PM though.
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post
Chas91Z28
Engine/Drivetrain/Suspension Wanted
10
10-22-2015 10:12 AM