[WA] Holley Stealth Ram and Commander 950 PRO ECU/wiring
#1
Supreme Member
Thread Starter
Join Date: Feb 2000
Location: Seattle, Washington
Posts: 1,170
Likes: 0
Received 0 Likes
on
0 Posts
Car: '87 IROC-Z/'82 RX7
Engine: SBC 355/1.1L Rotary
Transmission: T56/5 Speed
Axle/Gears: 4.33/3.93
Holley Stealth Ram and Commander 950 PRO ECU/wiring
Holley Commander 950 PRO ECU Installed into modded thirdgen ECU housing.
Wiring harness for TPI car
I ran a WB02 so you'll need to run one, or buy a 3 wire heated o2 sensor and connector to solder into the harness.
Map Sensor
Distributor - Small Cap EFI OEM
IAT Sensor
GM Small Cap Dizzy Adapter Harness
Software
Serial Cable
$450
Stealthram Intake w/ Fuel Rails w/ Adjustable regulator.
Plenum has fittings on the back for PCV/Interior Vacuum/Regulator/Booster. Also the upper rad hose, water neck, adapter for sensors in the intake and ARP stainless intake bolts.
No Throttle Body/Injectors
Powder coated red base.
Sanded down cast plenum, polished and painted ribs.
Fits old or new style GM SBC Gen 1 Heads.
Uses -6AN fittings. I'll also throw in the Fuel Lines and fittings to make it fit your standard TPI fuel lines on a Camaro for $50 (Well over $100 to buy and make.)
Retails over $600
$350 or $400 w/ fuel lines/adapter fittings
Wiring harness for TPI car
I ran a WB02 so you'll need to run one, or buy a 3 wire heated o2 sensor and connector to solder into the harness.
Map Sensor
Distributor - Small Cap EFI OEM
IAT Sensor
GM Small Cap Dizzy Adapter Harness
Software
Serial Cable
$450
Stealthram Intake w/ Fuel Rails w/ Adjustable regulator.
Plenum has fittings on the back for PCV/Interior Vacuum/Regulator/Booster. Also the upper rad hose, water neck, adapter for sensors in the intake and ARP stainless intake bolts.
No Throttle Body/Injectors
Powder coated red base.
Sanded down cast plenum, polished and painted ribs.
Fits old or new style GM SBC Gen 1 Heads.
Uses -6AN fittings. I'll also throw in the Fuel Lines and fittings to make it fit your standard TPI fuel lines on a Camaro for $50 (Well over $100 to buy and make.)
Retails over $600
$350 or $400 w/ fuel lines/adapter fittings
#2
Junior Member
Join Date: May 2010
Location: ohio
Posts: 62
Likes: 0
Received 0 Likes
on
0 Posts
Car: 88 camaro, 87 TA
Engine: 454 stock, built 468 400hp+150 shot
Transmission: WC t5, m29 t56 spec stg3 clutch
Axle/Gears: 9 bolt 2.77, 9 bolt 3.70
Re: Holley Stealth Ram and Commander 950 PRO ECU/wiring
how much shipped to 44721.
#3
Supreme Member
Thread Starter
Join Date: Feb 2000
Location: Seattle, Washington
Posts: 1,170
Likes: 0
Received 0 Likes
on
0 Posts
Car: '87 IROC-Z/'82 RX7
Engine: SBC 355/1.1L Rotary
Transmission: T56/5 Speed
Axle/Gears: 4.33/3.93
Re: Holley Stealth Ram and Commander 950 PRO ECU/wiring
For the intake setup or the ECU setup?
Intake setup will be about $30 priority shipped with insurance.
ECU/wiring/dist will be about $25.
Intake setup will be about $30 priority shipped with insurance.
ECU/wiring/dist will be about $25.
#4
Junior Member
Join Date: May 2010
Location: ohio
Posts: 62
Likes: 0
Received 0 Likes
on
0 Posts
Car: 88 camaro, 87 TA
Engine: 454 stock, built 468 400hp+150 shot
Transmission: WC t5, m29 t56 spec stg3 clutch
Axle/Gears: 9 bolt 2.77, 9 bolt 3.70
Re: Holley Stealth Ram and Commander 950 PRO ECU/wiring
would you just sell the intake and fuel rails also adapters to stock tpi lines?? if so how much?
#5
Supreme Member
Thread Starter
Join Date: Feb 2000
Location: Seattle, Washington
Posts: 1,170
Likes: 0
Received 0 Likes
on
0 Posts
Car: '87 IROC-Z/'82 RX7
Engine: SBC 355/1.1L Rotary
Transmission: T56/5 Speed
Axle/Gears: 4.33/3.93
Re: Holley Stealth Ram and Commander 950 PRO ECU/wiring
$435 (calculated the shipping to 44721):
Intake Base
Plenum
Fuel Rails
Adjustable regulator
T-Stat 180
Water Neck
Upper Rad Hose
Braided -6AN Fuel Lines
Adapter fittings for the TPI fuel lines that come up infront of the master cylinder.
Intake Base
Plenum
Fuel Rails
Adjustable regulator
T-Stat 180
Water Neck
Upper Rad Hose
Braided -6AN Fuel Lines
Adapter fittings for the TPI fuel lines that come up infront of the master cylinder.
#7
Supreme Member
Thread Starter
Join Date: Feb 2000
Location: Seattle, Washington
Posts: 1,170
Likes: 0
Received 0 Likes
on
0 Posts
Car: '87 IROC-Z/'82 RX7
Engine: SBC 355/1.1L Rotary
Transmission: T56/5 Speed
Axle/Gears: 4.33/3.93
Re: Holley Stealth Ram and Commander 950 PRO ECU/wiring
~SOLD~
Trending Topics
#8
Junior Member
Join Date: Jun 2006
Location: Lemont, IL
Posts: 53
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1988 Camaro
Engine: 383
Transmission: Tremec TKO
Axle/Gears: 373
Re: Holley Stealth Ram and Commander 950 PRO ECU/wiring
Is everything gone? Looking for the ecm and harness?
#9
Junior Member
Join Date: Nov 2013
Location: North Jersey
Posts: 7
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1987 GTA
Engine: 383
Transmission: Tremec 3550
Axle/Gears: 373
Re: Holley Stealth Ram and Commander 950 PRO ECU/wiring
hey i think i have your old stealth ram set up. i bought it off a guy from marrietta ga. just looking at the pictures its identical to the point
Thread
Thread Starter
Forum
Replies
Last Post
Royal_Z
Engine/Drivetrain/Suspension Parts for Sale
4
09-30-2015 08:45 PM