SCCAjunkie

Got rid of the Firebird, now need to sell leftover parts...

Some pics are below, additional available upon request. If you have a specific pic request, let me know.

First up- TPI setup with cool parts.
Stock plenum, ported to match SLP runners (also ported inside the entry)- $50 (I do have the plate for over the distributor)
Stock TB with airfoil- $50
Stock base, matched to runners only- $50
SLP "siamesed" runners, transitions smoothed for better flow- $250
Stock fuel rails- $10
MAP sensor- $10
New EGR (5k miles)- $10 or free with base
Accel 24 lb. injectors (5k miles)- $100
Everything worked great on the car. Made real good power. When I sold the car, the guy didn't want the engine, so I got it all back. Note: Only the TPI setup is for sale, not the whole engine or anything else from it.
$400 for the whole setup, plus shipping (this is heavy and large)

Factory LS1 injectors- 24lb., VERY low miles (under 500)- set of 8- $130 shipped
They are shown at this link.


Parts to complete a T5 swap into an auto car- almost a complete kit
NEW Luk clutch- $100
Bellhousing- cleaned and painted- $25
Flywheel- this is the lighter one!- $50
NEW GM clutch cylinder setup (master and slave)- $25 SOLD!!!
NEW GM lower shift boot- $10
NEW clutch switch- $5
NEW GM clutch fork and pivot ball- $20
NEW Hurst shifter- $100
NEW custom upper shifter boot- red and grey leather- $10
$225 for all, plus shipping (this is sorta heavy and awkward size)
Sorry, I know I have the pedals and the center console panel somewhere, but I can't find them... Trans is NOT included.

NEW stainless SLP Y-pipe for L98 car- $125 plus shipping (light but LARGE box)

Stock TPI parts- all stock, and dirty
Plenum- $50
Runners- $25
Base- $50
Or $100 for all- NO HARDWARE or any other parts

Two REAR 16" "fiero style" Firebird wheels
Were painted white, I started stripping one
Good for drag tires...
$50 for the pair plus shipping

All items located in SE PA, so pickup is welcome.

?-90 Firebird front park light housings-both-not broken- $10 plus shipping

twistedz28

can you tell me what kind of t5 you have?

mmyers_417

would you be willing to sell just the slp runners and plenum or do u wanna keep it a package i live 15min across the bridge in jersey so local pickup shouldnt be a problem

twistedz28

sorry I thought you had the trans too I didn't read carefully enough.

qcworm

i am also intersted in the runners, would you lemt me got those?

SCCAjunkie

Twisted- the T5 is NOT included at this time, but may be for sale later. I'm not sure if it's going to be used for another project at this point.

As far as separating the runners- I have one person who asked fist about the whole package. Should that fall through, I *may* consider splitting it up. If that is the case, I will post here.

Rich2279

iTrader: (7)

What about seperating the Hurst shifter?

SCCAjunkie

PM me with an offer.

mmyers_417

ok let me know bc i have a vortec heads so i cant use the base anyway

ted gerlach

iTrader: (28)

interested in the y-pipe, but is it for a 350 car or 305 car?

SCCAjunkie

I bought it for a 350, but I thought it would fit both...

SCCAjunkie

Separate prices have been listed for all parts.

SCCAjunkie

Added LS1 injectors.

IROC-Z28_CAMARO

iTrader: (4)

I will take all of these and the bell housing. Please pm me and I will give you my adress so we can get a final price with shipping. Thanks.

NEW GM clutch cylinder setup (master and slave)- $25
NEW GM lower shift boot- $10
NEW clutch switch- $5
NEW GM clutch fork and pivot ball- $20

SCCAjunkie

Unfortunately, you were too late for the hydraulics.

Clutch m/c and slave SOLD, package price reduced to reflect that.

1985 camaro 350

is the bellhousing for a v8? if so i will buy it

SCCAjunkie

Yes it is, as far as I know. I never knew there was a difference...

1985 camaro 350

i didnt know there was a difference either until today. could u check to make sure its a v8 bellhousing and give me a price shipped to 73501 if it is?

SCCAjunkie

How would I know the difference? What can I look for?

8airoc

you still have the slp runners?? how much to 79912

SCCAjunkie

PM sent.

ls1>*

iTrader: (32)

do you still have the runners? are they earlier or later tpi setup?

LS4GXP

iTrader: (2)

intrested in the y pipe, whats the collector sizes?

luke j

iTrader: (1)

If 1985 camaro 350 doesn't take the Bellhousing, I will. Just be sure it bolted to the V8 please and it is for hydraulic clutch slave. Should be. Shipping quote to 46077.

Also, when u find pedals and top plate let me know how much. Again, just PM or E-Mail me. Thanks again

Stangski09

iTrader: (10)

Interested in the fuel rails. Please send pics to t.stang@live.ca
Are the injector holes clean and not marked up? Because I know guys like to shove flat heads in them to pry the injectors out.
So please send me detailed pics of the injectors openings.
And is there anything else wrong with them?

Ryanb56

I am interested in the shifter, bellhousing, and clutch fork if you can give me a shipping quote to 83843. Also pics of these items to braunryan@hotmail.com would be great if you can. Thanks.

1989GTATransAm

iTrader: (3)

I'm interested in the stock throttle body if it is for an 1989 to 1992 car.

ninetyone

iTrader: (2)

Do you still have the stock memcal? (chip)?

87SSTPI

iTrader: (7)

Anyone hear anything from this guy lately or know how to get ahold of him?
I tried a PM and the email address listed on his profile, both 3-5 days ago and nothing(???)
Anyone else get any response after showing interest in an item(s)?

86transam.man

iTrader: (3)

I sent pm also but only a day ago and have heard nothing. I am interested in the hurst shifter.

87SSTPI

iTrader: (7)

Well, too bad I guess

ajfincannon

is the bell housing for v8 if so send me piv message and i will more than liky get it

87SSTPI

iTrader: (7)

ajfincannon, This is one of those "drive-by" for sale postings. You know, they are here one second and then they never post again after people show interest in their parts. I wouldn't waste your time, but good luck.

dsudzina

Hi,
Do yo still have the clutch fork rubber boot and the bellhousing inspection cover? I have a 1983 daytona with a 305, and need these 2 parts. Thanks, Dave

nealey82

iTrader: (2)

u still have the t-5 bell housing?if so how much shipped to 28376. was it a 305 or 350?

SCCAjunkie

87SSTPI- I didn't get the message, and obviously haven't been on here in a while. I wouldn't call someone with 48 posts in a variety of forums a "driveby". Your inquiries were 2 months after the original post...

That said, I'll have to look what I have left of the trans. stuff. The ported TPI setup is gone. I still have the following items---

Y-pipe
Stock TPI pieces
LS1 injectors
Wheels
Park light housings

I'm in a deal-making mood.

If interested, email me at-- mattgreen((at))msquaredracing((dot))com

Formula383

iTrader: (3)

Looking for the SLP Y Pipe. Sent pm

83C_CamAroZ28

iTrader: (12)

do u still have the hurst shifter and the lower shift boot?...

SCCAjunkie

Reply sent on Y-pipe.

I'm still not sure on the trans parts. They are at my shop, and I am not there this week.

SCCAjunkie

Y-pipe is sold, paid, and delivered.