[OH] Lots Of Parts For Sale
#1
Junior Member
Thread Starter
iTrader: (3)
Join Date: Nov 2008
Location: Lima, Ohio and Ft. Lauderdale, FL
Posts: 93
Likes: 0
Received 1 Like
on
1 Post
Car: 1983 Camaro Z28
Engine: 350
Transmission: 700R4
Axle/Gears: 3.42
Lots Of Parts For Sale
I have some stuff for sale directly from my 1974 350 with 5,000 miles on it since it was rebuilt. I will ship the cam, headers, and the intake at your cost, as well as the heads and the cat back. The heads and cat back will be costly though.
First, I have a gently used cam and lifter set. It was classified as a "stage one" cam in my Engine Tech rebuild kit. It gave a smooth but aggressive idle in my 350, and had a smooth power band. Perfect for a stock to mild 305 or 350. Specs are as followed:
Stage 1 HP SBC 350 camshaft .050 Duration 204/214 Cam Lift .280/.295 Valve Lift Int .420 / Exh .443 Lobe Center 107/117
$50 OBO
Next, I have a set of stock 350 heads casting number 3998991. Originally had 23,000 miles on them, then I did a valve job and installed new valve seals before I put them on the engine. They look dirty in the pictures, but most of it is just from engine dis-assembly and will wipe right off. They are low compression heads with 75cc combustion chambers, perfect if you are going forced induction.
$75 OBO
Edelbrock Performer intake, used but in good condition. The center two mounting holes are elongated on each side (beats me as to why), but it has no effect on the intakes sealing or mounting properties.
$65 OBO
Lastly, I have a Flowmaster cat back that is less than 2 years old with 5,000 miles on it. It was custom made with a Flowmaster 80 series muffler, 2 1/4" intermediate pipe, and dual 2.5" tail pipes with chrome tips. Tips clean up very nice, one of them has a very small dent in it (not noticeable when it's on the car.) The pipes are welded into the muffler so it will make it a little more difficult to ship, but it's doable.
$100 OBO
First, I have a gently used cam and lifter set. It was classified as a "stage one" cam in my Engine Tech rebuild kit. It gave a smooth but aggressive idle in my 350, and had a smooth power band. Perfect for a stock to mild 305 or 350. Specs are as followed:
Stage 1 HP SBC 350 camshaft .050 Duration 204/214 Cam Lift .280/.295 Valve Lift Int .420 / Exh .443 Lobe Center 107/117
$50 OBO
Next, I have a set of stock 350 heads casting number 3998991. Originally had 23,000 miles on them, then I did a valve job and installed new valve seals before I put them on the engine. They look dirty in the pictures, but most of it is just from engine dis-assembly and will wipe right off. They are low compression heads with 75cc combustion chambers, perfect if you are going forced induction.
$75 OBO
Edelbrock Performer intake, used but in good condition. The center two mounting holes are elongated on each side (beats me as to why), but it has no effect on the intakes sealing or mounting properties.
$65 OBO
Lastly, I have a Flowmaster cat back that is less than 2 years old with 5,000 miles on it. It was custom made with a Flowmaster 80 series muffler, 2 1/4" intermediate pipe, and dual 2.5" tail pipes with chrome tips. Tips clean up very nice, one of them has a very small dent in it (not noticeable when it's on the car.) The pipes are welded into the muffler so it will make it a little more difficult to ship, but it's doable.
$100 OBO
Last edited by Jr. Mechanic; 04-07-2010 at 10:25 PM.
#3
Senior Member
iTrader: (10)
Join Date: Aug 2008
Location: Winchester, VA
Posts: 638
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Camaro RS/1989 Vert RS
Engine: 355/350
Transmission: T-5/T-5
Axle/Gears: BW9bolt3.45posi/3.23 Posi
Re: Lots Of Parts For Sale
The intake bolt holes are elongated to fit post 87 blocks.
Trending Topics
#10
Member
Join Date: Jul 2009
Location: Richmond,VA
Posts: 149
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1984 Trans Am, 1986 Fiero SE
Engine: 5.0 H.O., 2.8
Transmission: T5, M4 Muncie
Axle/Gears: 3.73 disc posi, CAVALIER AXLES!!
Re: Lots Of Parts For Sale
Pmed......Get back to me.
#12
Junior Member
Join Date: Feb 2010
Location: Collegestation Texas
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1989 Camaro RS
Engine: 5.0
Re: Lots Of Parts For Sale
Hey you still have the headers and intake? will the intake fit on a 305 TBI?
Last edited by Aztec12; 03-22-2010 at 02:45 PM.
#13
Senior Member
iTrader: (1)
Join Date: Sep 2007
Location: New Philadelphia/ Canton OH
Posts: 914
Likes: 0
Received 1 Like
on
1 Post
Car: 1991 RS, 84 El Camino conquista RIP
Engine: 5.0 (for now)
Transmission: 4L60
Axle/Gears: 2.xx torsen limited slip & 3.42 ope
Re: Lots Of Parts For Sale
dibs on the exhaust. give me a shipping cost to 44663 and consider it sold. (the cat back)
#15
Junior Member
Thread Starter
iTrader: (3)
Join Date: Nov 2008
Location: Lima, Ohio and Ft. Lauderdale, FL
Posts: 93
Likes: 0
Received 1 Like
on
1 Post
Car: 1983 Camaro Z28
Engine: 350
Transmission: 700R4
Axle/Gears: 3.42
Re: Lots Of Parts For Sale
All of the sales fell though, everything is still for sale.
#16
Junior Member
Thread Starter
iTrader: (3)
Join Date: Nov 2008
Location: Lima, Ohio and Ft. Lauderdale, FL
Posts: 93
Likes: 0
Received 1 Like
on
1 Post
Car: 1983 Camaro Z28
Engine: 350
Transmission: 700R4
Axle/Gears: 3.42
Re: Lots Of Parts For Sale
Headers are sold, prices updated. I need to get rid of this stuff guys!
Thread
Thread Starter
Forum
Replies
Last Post
1992 Trans Am
History / Originality
27
05-10-2023 07:19 PM