[VA] SBC parts Crane Holley Vortec heads
11-25-2009, 07:18 PM
#1
Member
Thread Starter
iTrader: (7)
Join Date: Aug 2002
Posts: 178
Likes: 0
Received 0 Likes
on
0 Posts
SBC parts Crane Holley Vortec heads
I am selling some of my spare parts to fund finishing my newest project.
Crane Cam and lifter kit NEW IN BOX Specs are :
230 @.050 .465 lift intake and exhaust with 1.5 rockers and a 106 LSA. This cam has a choppy idle in a 350, runs and sounds great IMO. $100 + shipping
Crane Cam and lifter kit NEW IN BOX Specs are :
230 @.050 .465 lift intake and exhaust with 1.5 rockers and a 106 LSA. This cam has a choppy idle in a 350, runs and sounds great IMO. $100 + shipping
Last edited by flyin89; 12-09-2009 at 09:16 AM.
11-25-2009, 08:08 PM
#3
Supreme Member
iTrader: (13)
Join Date: Apr 2005
Location: Not in Kansas anymore
Posts: 7,732
Likes: 0
Received 11 Likes
on
11 Posts
Car: 82 Z28
Engine: 383 SP EFI/ 4150 TB
Transmission: T400
Axle/Gears: QP 9" 3.73
Re: SBC parts Crane Holley Vortec heads
Std 1 pce balance on crank ( weight on flexplate ) or internal balance?
Trending Topics
11-25-2009, 10:30 PM
#8
Supreme Member
iTrader: (6)
Join Date: Dec 2008
Location: Norwalk, CA
Posts: 2,540
Likes: 0
Received 0 Likes
on
0 Posts
Car: 91Z28
Engine: 5.7 ls1
Transmission: 4l60e
Axle/Gears: 3.42
Re: SBC parts Crane Holley Vortec heads
Oh never mind or do you know if you can swap from roller to flat
11-28-2009, 10:22 PM
#11
Junior Member
Join Date: Jul 2009
Location: Minneapolis, MN
Posts: 4
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1996 Cadillac/1986 Firebird
Engine: 4.6 Northstar/305V8
Re: SBC parts Crane Holley Vortec heads
I am selling some of my spare parts to fund finishing my newest project.
A Holley Avenger 670 carb. Pretty clean and ran good. $125 local pick-up or $140 shipped in the USA.
Crane Cam and lifter kit NEW IN BOX SPecs are :
230 @.050 .465 lift intake and exhaust with 1.5 rockers and a 106 LSA. This cam has a choppy idle in a 350, runs and sounds great IMO. $100 + shipping
Vortec heads 906 WITHOUT hardened seats. These are the same as any 062 head except the symbol at the front. Matched pair with 80k miles you can use them as they are or have them modded. $150 for the pair + shipping
A SCAT NODULAR 383 crankshaft knife edged counterweights 3.75 stroke, 350 stock mains size 1 pc. rear main seal will include new standard bearings $150.00 + shipping
A Holley Avenger 670 carb. Pretty clean and ran good. $125 local pick-up or $140 shipped in the USA.
Crane Cam and lifter kit NEW IN BOX SPecs are :
230 @.050 .465 lift intake and exhaust with 1.5 rockers and a 106 LSA. This cam has a choppy idle in a 350, runs and sounds great IMO. $100 + shipping
Vortec heads 906 WITHOUT hardened seats. These are the same as any 062 head except the symbol at the front. Matched pair with 80k miles you can use them as they are or have them modded. $150 for the pair + shipping
A SCAT NODULAR 383 crankshaft knife edged counterweights 3.75 stroke, 350 stock mains size 1 pc. rear main seal will include new standard bearings $150.00 + shipping
12-01-2009, 07:40 AM
#14
Junior Member
Join Date: Jul 2009
Location: Minneapolis, MN
Posts: 4
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1996 Cadillac/1986 Firebird
Engine: 4.6 Northstar/305V8
Re: SBC parts Crane Holley Vortec heads
i really want that crank, i'm just waiting for an answer via PM
12-02-2009, 09:31 AM
#15
Member
Thread Starter
iTrader: (7)
Join Date: Aug 2002
Posts: 178
Likes: 0
Received 0 Likes
on
0 Posts
Re: SBC parts Crane Holley Vortec heads
All PM's responded to. Here is just a bit more info on the cam:
It is a hyd. flat tappet cam like pretty much every 1955-1985 SBC. It can be used on post 1986 engines, If it was Hyd roller you would need to swap to the reg SBC flat-tappet cam timing chain and pushrods.
The cam is basically what they would call a 3/4 race cam, it is a bit radical for mild small blocks, with the .230 duration and a 106 LSA, it will have the race car sound without the race parts breakage of extremely high lift (only .465 lift with 1.5 rockers or around .500 with 1.6 rockers.)
It is a hyd. flat tappet cam like pretty much every 1955-1985 SBC. It can be used on post 1986 engines, If it was Hyd roller you would need to swap to the reg SBC flat-tappet cam timing chain and pushrods.
The cam is basically what they would call a 3/4 race cam, it is a bit radical for mild small blocks, with the .230 duration and a 106 LSA, it will have the race car sound without the race parts breakage of extremely high lift (only .465 lift with 1.5 rockers or around .500 with 1.6 rockers.)
Last edited by flyin89; 12-02-2009 at 09:37 AM.
12-04-2009, 08:54 AM
#18
Member
Thread Starter
iTrader: (7)
Join Date: Aug 2002
Posts: 178
Likes: 0
Received 0 Likes
on
0 Posts
Re: SBC parts Crane Holley Vortec heads
I'll take $140 shipped for the carb and that includes the fuel line. IMO I am losimg enough money on it. Yes I take paypal.
I will take $100 for the scat 383 Crank without the bearings + buyer pays actual shipping. or $100 local pickup. (Located in VA.)
I will take $100 for the scat 383 Crank without the bearings + buyer pays actual shipping. or $100 local pickup. (Located in VA.)
12-07-2009, 09:59 PM
#21
Member
Join Date: Dec 2006
Posts: 224
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 camaro z28
Engine: 350sbc
Transmission: TKO 600
Axle/Gears: stock axle with 4.11's
Re: SBC parts Crane Holley Vortec heads
are the rockers self guiding for those heads or were you using guide plates??
how much for heads shipped to 98380
how much for heads shipped to 98380
Thread
Thread Starter
Forum
Replies
Last Post
84z96L31vortec
Tech / General Engine
7
08-20-2017 12:16 AM
L98GTA87
Engine/Drivetrain/Suspension Wanted
1
08-11-2015 06:55 PM
84z96L31vortec
North East Region
1
08-10-2015 08:27 PM
