SLP 1 3/4 Headers
#1
Senior Member
Thread Starter
iTrader: (6)
Join Date: Sep 2001
Location: Richmond Hill, GA
Posts: 632
Likes: 0
Received 5 Likes
on
3 Posts
Car: They all sit.
Engine: LB9,LB9, LS1, LT4, LT4
Transmission: T5, T5, 4L60, T56, T56
Delete
I've got some SLP headers i'd like to try and swap out for some longtubes and y-pipe. they don't need to be coated, but must be emission free headers.
I don't know much about the SLP headers, except they dont make them anymore. from what ive gathered their stainless steel. once i get them off the car i'll polish them up. have the pipes to hook them to a y-pipe too, but will all need welded.
I have no idea what to ask at the moment, as i'd like to try and trade because i need to put something else right back on when i get them off.
I'll get some pics uploaded soon.
$500
feel free to make offers/trades
I don't know much about the SLP headers, except they dont make them anymore. from what ive gathered their stainless steel. once i get them off the car i'll polish them up. have the pipes to hook them to a y-pipe too, but will all need welded.
I have no idea what to ask at the moment, as i'd like to try and trade because i need to put something else right back on when i get them off.
I'll get some pics uploaded soon.
$500
feel free to make offers/trades
Last edited by jer4251; 04-30-2011 at 07:35 PM.
#3
Senior Member
Thread Starter
iTrader: (6)
Join Date: Sep 2001
Location: Richmond Hill, GA
Posts: 632
Likes: 0
Received 5 Likes
on
3 Posts
Car: They all sit.
Engine: LB9,LB9, LS1, LT4, LT4
Transmission: T5, T5, 4L60, T56, T56
Re: SLP 1 3/4 Headers
yes, they have the air tubes. I'll try to get some pics today, they are on the car still.
#4
Senior Member
Thread Starter
iTrader: (6)
Join Date: Sep 2001
Location: Richmond Hill, GA
Posts: 632
Likes: 0
Received 5 Likes
on
3 Posts
Car: They all sit.
Engine: LB9,LB9, LS1, LT4, LT4
Transmission: T5, T5, 4L60, T56, T56
Re: SLP 1 3/4 Headers
here are some pics. i cleaned off part of the drivers side to show they are in great shape. I don't see any dents in them, not even by the steering shaft. they should clean up great once off. the y-pipe was cut right sfter it makes the 90* turn under the pass side. the one pipe is loose, thats why its lower. just need to weld these to your dual cat setup or throw in a y and weld them to the single cat. or make a custom setup
#5
Senior Member
Thread Starter
iTrader: (6)
Join Date: Sep 2001
Location: Richmond Hill, GA
Posts: 632
Likes: 0
Received 5 Likes
on
3 Posts
Car: They all sit.
Engine: LB9,LB9, LS1, LT4, LT4
Transmission: T5, T5, 4L60, T56, T56
Re: SLP 1 3/4 Headers
this is the car their comming off of. 1991 Z28 with L98 5.7L
#7
Senior Member
Thread Starter
iTrader: (6)
Join Date: Sep 2001
Location: Richmond Hill, GA
Posts: 632
Likes: 0
Received 5 Likes
on
3 Posts
Car: They all sit.
Engine: LB9,LB9, LS1, LT4, LT4
Transmission: T5, T5, 4L60, T56, T56
Re: SLP 1 3/4 Headers
it can be used for either at this point. u just need to put a y where the 2 pipes run next to each other.
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post
redformula88
Engine/Drivetrain/Suspension Parts for Sale
2
10-14-2015 06:08 PM