Gauging interest in EFI 355 small block 404hp 407ft-lbs

Reply Subscribe

Thread Tools

Search this Thread

02-20-2008, 11:09 AM

eXesiv|83ta

TGO Supporter

Thread Starter

iTrader: (4)

Join Date: Oct 2004

Location: Rockford, MI

Posts: 300

Likes: 0

Received 0 Likes on 0 Posts

Car: 1983 Pontiac Trans AM

Engine: 355 chevy

Transmission: 700R4 Built

Axle/Gears: Built 10 bolt 3.73 gears

Gauging interest in EFI 355 small block 404hp 407ft-lbs

Hey guys I am looking at selling my gen 1 355 roller motor for a new LS based motor. I need to sell my setup for the money I need. I have the dyno sheet for it and it makes 407hp and 404ft-lbs of torque. It has an OK tune on it right now, I'm sure if it was tuned professionally it would make more. This motor has two summer seasons on it with approximately 8,000 miles total. I am in Michigan.

87 350 bored .030 2bolt main
Melling HV oil pump and pickup ARP pump shaft
Stock crank was polished and chamfered
Scat forged I beam 5.7" rods
All block work done at Performance Engineering in Jenison, MI
I have all receipts
Comp cams XR276HR cam 282ad dur 502/510 lift with matching springs
Summit 1.5 roller rockers with ARP screw in studs and guideplates
Speed pro hypereutectic pistons flat top 10.1:1 comp with 64cc heads
Dart iron eagle platinum heads 200cc intake 2.02 1.60 valves
Holley Stealth Ram with FAST fuel injection
BBK 58mm throttle body
ARP main studs with Moroso windage tray
MSD pro billet distributor(small cap)
MSD wires and remote mount coil
MSD 6al

I am interested in selling the entire set up from ignition to oil pan or if I have to I will part it out.

Please email me any inquiries or questions as I am not on here alot.
triggerarg@hotmail.com
I also have pictures and can get specific pictures as needed.

thanks,

Justin

Last edited by eXesiv|83ta; 02-20-2008 at 02:30 PM.

Reply Like

02-22-2008, 03:57 PM

eXesiv|83ta

TGO Supporter

Thread Starter

iTrader: (4)

Join Date: Oct 2004

Location: Rockford, MI

Posts: 300

Likes: 0

Received 0 Likes on 0 Posts

Car: 1983 Pontiac Trans AM

Engine: 355 chevy

Transmission: 700R4 Built

Axle/Gears: Built 10 bolt 3.73 gears

Re: Gauging interest in EFI 355 small block 404hp 407ft-lbs

Bump!

Willing to part out also!

Reply Like

02-22-2008, 10:52 PM

djtricia

Senior Member

iTrader: (4)

Join Date: Feb 2005

Location: Portage, MI.

Posts: 593

Likes: 0

Received 0 Likes on 0 Posts

Car: 1986 Z-28

Engine: 350

Transmission: 700R4

Re: Gauging interest in EFI 355 small block 404hp 407ft-lbs

Prices might help?

Reply Like

02-24-2008, 06:27 PM

eXesiv|83ta

TGO Supporter

Thread Starter

iTrader: (4)

Join Date: Oct 2004

Location: Rockford, MI

Posts: 300

Likes: 0

Received 0 Likes on 0 Posts

Car: 1983 Pontiac Trans AM

Engine: 355 chevy

Transmission: 700R4 Built

Axle/Gears: Built 10 bolt 3.73 gears

Re: Gauging interest in EFI 355 small block 404hp 407ft-lbs

OK,right now I would like to get $4,500 for the whole setup. This is a put into your car and drive it setup. I will even throw in the accessories that I have with the half serpentine system on it. Obviously the price is negotiable and if you want individual prices please post up here what your interested in and I will try and throw out a price. The motor is in my car right now and if you would like a ride or want to see it please email me. My email is above and if you would like to talk just shoot me an email and I will email back my phone number.Thanks!!Justin

Reply Like