What bin to start with for my setup?
11-14-2014, 03:13 AM
#1
Member
Thread Starter
iTrader: (8)
Join Date: Mar 2006
Location: TN
Posts: 205
Likes: 0
Received 1 Like
on
1 Post
Car: 92 rs z28 clone
Engine: forged 350
Transmission: 700r4 fully built
Axle/Gears: moser axles eaton posi 3.73 gears
What bin to start with for my setup?
I am just getting my new setup together and ready to go in the car I will be tuning with EBL and was wondering should I start with a 92 l98 bin or would a y body l98 bin be a better bin to start with because they came with the better flowing alum. heads and what not?
11-14-2014, 07:19 AM
#2
Moderator
iTrader: (1)
Join Date: Mar 2002
Location: Chasing Electrons
Posts: 18,405
Likes: 0
Received 216 Likes
on
202 Posts
Car: check
Engine: check
Transmission: check
Re: What bin to start with for my setup?
Is this the engine in your sig? If so I'd start with a TPI BIN (Port Mod) and copy the VE tables over from the base TBI BIN. The HSR is going to produce a completely different torque curve then a TPI intake.
Assuming this is an EBL Flash (not P4 Flash), start with the EBL_F_3005 BIN. That one is set up as an iron head L98 with an automatic.
Then as mentioned copy the VE tables over from the base TBI BIN. Do some fuel tuning and see how it is. Can then try this semi-tuned BIN with the main & extended SA tables copied over from the EBL_F_3006 BIN (L98 w/alum heads & 6-spd). See if that provides better driveability and/or power.
RBob.
Assuming this is an EBL Flash (not P4 Flash), start with the EBL_F_3005 BIN. That one is set up as an iron head L98 with an automatic.
Then as mentioned copy the VE tables over from the base TBI BIN. Do some fuel tuning and see how it is. Can then try this semi-tuned BIN with the main & extended SA tables copied over from the EBL_F_3006 BIN (L98 w/alum heads & 6-spd). See if that provides better driveability and/or power.
RBob.
11-14-2014, 10:11 AM
#3
Member
Thread Starter
iTrader: (8)
Join Date: Mar 2006
Location: TN
Posts: 205
Likes: 0
Received 1 Like
on
1 Post
Car: 92 rs z28 clone
Engine: forged 350
Transmission: 700r4 fully built
Axle/Gears: moser axles eaton posi 3.73 gears
Re: What bin to start with for my setup?
Is this the engine in your sig? If so I'd start with a TPI BIN (Port Mod) and copy the VE tables over from the base TBI BIN. The HSR is going to produce a completely different torque curve then a TPI intake.
Assuming this is an EBL Flash (not P4 Flash), start with the EBL_F_3005 BIN. That one is set up as an iron head L98 with an automatic.
Then as mentioned copy the VE tables over from the base TBI BIN. Do some fuel tuning and see how it is. Can then try this semi-tuned BIN with the main & extended SA tables copied over from the EBL_F_3006 BIN (L98 w/alum heads & 6-spd). See if that provides better driveability and/or power.
RBob.
Assuming this is an EBL Flash (not P4 Flash), start with the EBL_F_3005 BIN. That one is set up as an iron head L98 with an automatic.
Then as mentioned copy the VE tables over from the base TBI BIN. Do some fuel tuning and see how it is. Can then try this semi-tuned BIN with the main & extended SA tables copied over from the EBL_F_3006 BIN (L98 w/alum heads & 6-spd). See if that provides better driveability and/or power.
RBob.
11-14-2014, 10:50 AM
#5
Member
Thread Starter
iTrader: (8)
Join Date: Mar 2006
Location: TN
Posts: 205
Likes: 0
Received 1 Like
on
1 Post
Car: 92 rs z28 clone
Engine: forged 350
Transmission: 700r4 fully built
Axle/Gears: moser axles eaton posi 3.73 gears
Re: What bin to start with for my setup?
Okay thanks I will do that also.
Thread
Thread Starter
Forum
Replies
Last Post
evilstuie
Tech / General Engine
22
01-09-2020 08:29 PM