EBL .bin settings
#1
EBL .bin settings
I am asking if these changes were warrented. Changes done two years ago GM 7.4L TBI. GM 80 lbs injectors runnin 20 lbs fuel pressure. I presume changes done due to slower opening time of my injectors?
ron.bin ... EBL.bin(305 auto)
PRP prop gain duration idle 3.00 ... 5.00
" offset 14.0 ... 20.0
IAC B9in idle speed 700 ... 0
Inj correction multiplier 12.8 ... 7.02
" offset 14.4(??) 442.5 ... 396.80
PRP gain multiplier vs airflow (example 80 grams/sec) 50 .... 100
Thanks.
ron.bin ... EBL.bin(305 auto)
PRP prop gain duration idle 3.00 ... 5.00
" offset 14.0 ... 20.0
IAC B9in idle speed 700 ... 0
Inj correction multiplier 12.8 ... 7.02
" offset 14.4(??) 442.5 ... 396.80
PRP gain multiplier vs airflow (example 80 grams/sec) 50 .... 100
Thanks.
Last edited by Ronny; 12-06-2010 at 02:55 PM.
#2
Moderator
iTrader: (1)
Join Date: Mar 2002
Location: Chasing Electrons
Posts: 18,406
Likes: 0
Received 216 Likes
on
202 Posts
Car: check
Engine: check
Transmission: check
Re: EBL .bin settings
I am asking if these changes were warrented. Changes done two years ago GM 7.4L TBI. GM 80 lbs injectors runnin 20 lbs fuel pressure. I presume changes done due to slower opening time of my injectors?
ron.bin ... EBL.bin(305 auto)
PRP prop gain duration idle 3.00 ... 5.00
" offset 14.0 ... 20.0
IAC B9in idle speed 700 ... 0
Inj correction multiplier 12.8 ... 7.02
" offset 14.4(??) 442.5 ... 396.80
PRP gain multiplier vs airflow (example 80 grams/sec) 50 .... 100
Thanks.
ron.bin ... EBL.bin(305 auto)
PRP prop gain duration idle 3.00 ... 5.00
" offset 14.0 ... 20.0
IAC B9in idle speed 700 ... 0
Inj correction multiplier 12.8 ... 7.02
" offset 14.4(??) 442.5 ... 396.80
PRP gain multiplier vs airflow (example 80 grams/sec) 50 .... 100
Thanks.
RBob.
#4
Re: EBL .bin settings
TBI settings not published. TPI are published . basically a educated guestimate. My idle speed IAC only allowed to increase the idle speed. TSS set min. GM settings for 7.4L TBI may be hacked but many of us run mod 350/383
ps tko 600 going this week
ps tko 600 going this week
#5
Member
iTrader: (11)
Re: EBL .bin settings
I think I have found what I was looking for. But I should assume that this was already done in the 3001.bin file correct?
Re: 454 tbi
Quote:
Originally Posted by freaky View Post
ok setting up my tune fore the 454tbi an i want to make sure i understand this .i have #55.0 an i'm putting in 80.5 so do i minus the tables by 31.5% ? or do i just take 80.5 an subtract 55 from that leaving 25.5 .then subtract the values by 25.5 from the tables you listed ? ?
thanks ...
55 / 80.5 = 0.68, multiply the table values by .68
RBob
Re: 454 tbi
Quote:
Originally Posted by freaky View Post
ok setting up my tune fore the 454tbi an i want to make sure i understand this .i have #55.0 an i'm putting in 80.5 so do i minus the tables by 31.5% ? or do i just take 80.5 an subtract 55 from that leaving 25.5 .then subtract the values by 25.5 from the tables you listed ? ?
thanks ...
55 / 80.5 = 0.68, multiply the table values by .68
RBob
#6
Member
iTrader: (11)
Re: EBL .bin settings
I found some original bin files on http://gearhead-efi.com/gearhead-efi/bin/
I think I'm going to get an excel chart going to see if the math all works out. The few I had already looked at like the 2025 and the 3001, had very odd numbers in the tables.
I think I'm going to get an excel chart going to see if the math all works out. The few I had already looked at like the 2025 and the 3001, had very odd numbers in the tables.
Thread
Thread Starter
Forum
Replies
Last Post
[Sold] Accel 30# injectors
hydrolic144
Engine/Drivetrain/Suspension Parts for Sale
0
08-29-2015 04:14 PM
mustangdmurder
Engine/Drivetrain/Suspension Parts for Sale
2
08-21-2015 07:17 PM