Tunerpro RT V4?
#1
Junior Member
Thread Starter
Tunerpro RT V4?
I have a 1988 5.7L TPI with ECU 1227165. Can someone point me in the direction or have a link on what Data Stream Definition I need to data log my car.
I've downloaded one but itdoesn't seem to be working.
please see link below. Thanks.
I've downloaded one but itdoesn't seem to be working.
please see link below. Thanks.
Last edited by JuanZ28; 03-22-2024 at 01:29 PM.
The following users liked this post:
JuanZ28 (03-23-2024)
#4
Junior Member
Thread Starter
Re: Tunerpro RT V4?
Hi I am using a USB to TTL adapter by SB UART.
I jumper the TX and RX together and connected the wire to the car ALDL diagnostic connector port M and the Ground wire to port A.
The data is weird, I either have a bad ECU or the wrong Data Definition.
The $32b ads/ adx is that a Bin file or a Data logging Definition file? I need a data logging file for a 1988 Camaro 5.7 TPI with MAF.
Thank you.
I jumper the TX and RX together and connected the wire to the car ALDL diagnostic connector port M and the Ground wire to port A.
The data is weird, I either have a bad ECU or the wrong Data Definition.
The $32b ads/ adx is that a Bin file or a Data logging Definition file? I need a data logging file for a 1988 Camaro 5.7 TPI with MAF.
Thank you.
The following users liked this post:
JuanZ28 (03-23-2024)
#6
Junior Member
Thread Starter
Re: Tunerpro RT V4?
I've tried Tunerpro RT V5 download an ads definition file then imported it to convert to and adx file. But Tunerpro RT V5 won't connect to my ECU. I'm new to this Tunerpro RT and I'm unaware of the 10k mode.
#7
Sponsor
iTrader: (92)
Re: Tunerpro RT V4?
https://www.thirdgen.org/forums/tpi/...i-da-data.html
you can also use winaldl to see if data looks good. Before you connect tp or winaldl use a 10k ohm resistor across a to b at the aldl then hit connect.
you can also use winaldl to see if data looks good. Before you connect tp or winaldl use a 10k ohm resistor across a to b at the aldl then hit connect.
The following users liked this post:
JuanZ28 (03-23-2024)
Trending Topics
#8
Junior Member
Thread Starter
Re: Tunerpro RT V4?
I will order some 10k ohm resistors.
Also Im running the Bosch3 fuel injectors and I have another ecu 16198259 that has a Delco ANYH 9298. Can you tune/burn it to be use for my car?
Also Im running the Bosch3 fuel injectors and I have another ecu 16198259 that has a Delco ANYH 9298. Can you tune/burn it to be use for my car?
#10
Member
Join Date: Sep 2002
Location: honolulu
Posts: 187
Likes: 0
Received 10 Likes
on
10 Posts
Car: '86MCSS
Engine: 396 .030"
Transmission: M20
Re: Tunerpro RT V4?
https://www.thirdgen.org/forums/tpi/...i-da-data.html
you can also use winaldl to see if data looks good. Before you connect tp or winaldl use a 10k ohm resistor across a to b at the aldl then hit connect.
you can also use winaldl to see if data looks good. Before you connect tp or winaldl use a 10k ohm resistor across a to b at the aldl then hit connect.
ads/adx is the datalogging file used with tp v4 and v5 respectively.
The following users liked this post:
JuanZ28 (03-23-2024)
Thread
Thread Starter
Forum
Replies
Last Post