DFI and ECM Discuss all aspects of DFI (Digital Fuel Injection), ECMs (Electronic Control Module), scanners, and diagnostic equipment. Fine tune your Third Gen computer system for top performance.

Codes 33,34,36

Thread Tools
 
Search this Thread
 
Old 08-24-2004, 12:23 AM
  #1  
Junior Member
Thread Starter
 
SassyTA's Avatar
 
Join Date: Aug 2004
Location: So Cal
Posts: 1
Likes: 0
Received 0 Likes on 0 Posts
Car: 1988 GTA Blk
Engine: 305
Transmission: 5spd
Codes 33,34,36

I just purchased a 1988 Blk GTA 305 5spd that died
on me while driving without any symptoms. Engine would
restart but not remain ideling. Found a code 34, installed
a new MAF but had same problem. Next I replaced both the
MAF burnoff relay and MAF power relay. Now I have three
codes,33,34,36 but car seems to be running fine except for
start up. I know this seems to be a common problem and I
researched the archived threads on this board but could not
seem to come up with what to check next.
Sorry this is a little lengthy, any suggestions would be greatly
appreciated.
Look forward to being a member of this board.

Christina
Old 08-24-2004, 08:37 AM
  #2  
TGO Supporter

 
Trickster's Avatar
 
Join Date: Sep 2003
Location: conway, s.c.
Posts: 6,127
Likes: 0
Received 8 Likes on 8 Posts
Car: 1989 Iroc-Z
Engine: 5.7L TPI
Transmission: 700R4
Hello Christina,

Welcome to the board. What you need to do is disconnect the battery positive cable for about 5 to 10 minutes to clear the trouble codes from the ECM. After you have reconnected the battery, take the car for a test drive and see if the SES light comes back on and check the code. Your three codes that you had were probably codes that hadn't been cleared. BTW, after reconnecting the battery you will also have to re-enter any pre-sets that you had on your stereo and clock.
Old 08-24-2004, 08:54 AM
  #3  
Moderator

iTrader: (1)
 
RBob's Avatar
 
Join Date: Mar 2002
Location: Chasing Electrons
Posts: 18,405
Likes: 0
Received 216 Likes on 202 Posts
Car: check
Engine: check
Transmission: check
Please make it the negative battery cable as the one to disconnect. Not like the Trickster to slip up like that

RBob.
Old 08-24-2004, 09:11 AM
  #4  
TGO Supporter

 
Trickster's Avatar
 
Join Date: Sep 2003
Location: conway, s.c.
Posts: 6,127
Likes: 0
Received 8 Likes on 8 Posts
Car: 1989 Iroc-Z
Engine: 5.7L TPI
Transmission: 700R4
Originally posted by RBob
Please make it the negative battery cable as the one to disconnect. Not like the Trickster to slip up like that

RBob.
Hey RBob,

The reason that I mentioned the positive cable is because I have had several instances in the past where disconnecting the negative battery cable produced no results in clearing the codes. This has been the case on more than one make and model car. The service manual also states to disconnect the ECM power feed at the positive battery terminal pigtail, the inline fuse holder, or the ECM fuse in the fuse block. In parenthesis it say, "the negative battery terminal may be disconnected, but other on-board memory data such as preset radio tuning will also be lost.
Old 08-24-2004, 09:37 AM
  #5  
Supreme Member

iTrader: (2)
 
dimented24x7's Avatar
 
Join Date: Jan 2002
Location: Moorestown, NJ
Posts: 9,962
Likes: 0
Received 3 Likes on 3 Posts
Car: 88 Camaro SC
Engine: SFI'd 350
Transmission: TKO 500
Axle/Gears: 9-bolt w/ 3.23's
disconnecting either cable will break the circuit. Ive absent mindedly disconnected teh positive first on some occasions. Nothing like welding a tool to the fender.
Old 08-24-2004, 01:26 PM
  #6  
Junior Member
Thread Starter
 
SassyTA's Avatar
 
Join Date: Aug 2004
Location: So Cal
Posts: 1
Likes: 0
Received 0 Likes on 0 Posts
Car: 1988 GTA Blk
Engine: 305
Transmission: 5spd
Thanks for the info guys.
I am going to drop the car off
tomorrow since I have already paid
the tech for this "repair". I will report
back with results.

Christina
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
89-IROCZ-5.0TPI
TPI
10
02-22-2022 09:26 PM
Falcon50
DFI and ECM
81
08-22-2020 03:26 PM
racereese
Tech / General Engine
14
10-03-2015 03:46 PM
Luigytico09
TPI
0
10-01-2015 08:46 AM
dusterbd
TPI
0
09-29-2015 08:40 AM



Quick Reply: Codes 33,34,36



All times are GMT -5. The time now is 02:36 AM.