When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Auto Detailing and AppearanceShare tips and tricks on how to make your Third Gen shine! Get opinions on products or how something tasteful looks on your Chevrolet Camaro or Pontiac Firebird.
Hello everyone. I have a request for those of you who have the power bulge hood with the louvered decal on it.
I purchased that decal from Phoenix Graphics and sent it to a company to have something custom made, however, they are no longer communicating with me so there goes that $150 decal.
Would anyone be able to trace the decal onto paper as a template? I would just need the outer edges of it traced, not all the inner louver portion.
Any help would be appreciated. Thanks.
-Jim
Last edited by CharcoalBird; 10-11-2021 at 07:22 PM.
Reason: Title change.
Awfully large to try to trace, but here's a pic of a decal on a spare hood I have. 13-1/2" across the top. 4-1/2" across the bottom. 36" tall along the straight side. That oughta help you mock-up an outline.
Awfully large to try to trace, but here's a pic of a decal on a spare hood I have. 13-1/2" across the top. 4-1/2" across the bottom. 36" tall along the straight side. That oughta help you mock-up an outline.
Thank you for the reply, LAFireboyd. It is large, and I hate to order another decal that I'm not going to use. Nobody local that I know of has that hood decal. Guess I could just trace the lines of the power bulge. What I am having done is a real louver in place of the decal louvers.
I had sent the decal to TrackSpec to have this made similar to what they have been doing for the IROC hood louvers. After I sent the decal to them, they quit communicating with me. Member Morrow will now be doing it for me. Just need to provide him with a template.
I like the idea. Real louvers could be made to fit the bulge better than the decal does. If it works out, and people like it, I hope Morrow will be prepared to make more, rather than chalking it up to a one-off.
The products Trackspec offers on its website look good. And plenty of people have their IROC louvers, so it's obviously a legitimate operation. At least, keep after them to get your decal back.
Once I unveil them installed, I'm sure he will receive more requests for them.
Them? At first I was thinking you would be changing to a Power Bulge hood, which would require only one louver, obviously. But now it sounds like you might be keeping your RA2 hood, and installing them like IROC louvers? If this is the case, then wouldn't IROC louvers look the same, just as good? After all, the Trackspec IROC louvers, driver's side, specifically, is similar enough in shape to the power bulge, that it looks like it would almost fit, as it is. And nothing would need to be specially fabricated. Just saying, not criticizing, because I think I'm going to like whatever you're planning.
I thought of one other possibility, too, but I'll leave that alone, just in case, so you can try to keep your project under wraps, whatever it is, until you're ready to reveal.
Call the police department in the city where you sent the decal and see if they'll pay the company a visit... might scare them into sending your decal back...
Them? At first I was thinking you would be changing to a Power Bulge hood, which would require only one louver, obviously. But now it sounds like you might be keeping your RA2 hood, and installing them like IROC louvers? If this is the case, then wouldn't IROC louvers look the same, just as good? After all, the Trackspec IROC louvers, driver's side, specifically, is similar enough in shape to the power bulge, that it looks like it would almost fit, as it is. And nothing would need to be specially fabricated. Just saying, not criticizing, because I think I'm going to like whatever you're planning.
I thought of one other possibility, too, but I'll leave that alone, just in case, so you can try to keep your project under wraps, whatever it is, until you're ready to reveal.
I can see how that was confusing, apologies. I am switching to a power bulge hood and it will only be 1 just like factory.
I should be able to make the template based on your measurements and following the curvature on the hood. Will let you know how it turns out.
Edit: Received an email back from TrackSpec finally. Design is done and they will be working on the prototype next week.
Last edited by CharcoalBird; 02-11-2021 at 08:27 PM.
It's been 4 and a half months... anything good to report?
TrackSpec did not reply to my last email 2 or 3 months ago(has been almost 9 months since they received the decal.) I ended up sending another decal to Morrow in mid May, hopefully he will be finished with it soon.
Once the louver arrives from him, I'll send another e-mail to TrackSpec. The last e-mail I received from them they stated that the prototype would be arriving to their location with the next batch(January or Feb) as they had already made it. I will ask for my decal back and depending on their answer, I'll leave a review.
These look pretty nice. Would you be willing to share what you paid?
Thinking these might be helpful on my turbo ‘84 TA build.
What I paid and what you would pay may be different. Now that they have the template and sizing for their cnc machine. I paid $485 for them to custom make this for me. I have roughly $750 into this vent though.
Dropped it off at the paint shop yesterday. Next picture I post will be when I install it on the car.
You dropped off the hood at the paint shop on the 2nd? Today is the 11th. When do you expect to get it back? Does the louver bolt down easily, no curvature issues?
You dropped off the hood at the paint shop on the 2nd? Today is the 11th. When do you expect to get it back? Does the louver bolt down easily, no curvature issues?
I'm hoping to have it back somewhere around the 20-24th. Said he would get started on it this week. There should be no issue bolting it down. It does bend enough to lay flat through the curvature.
Now that you've accomplished your goal, you might consider changing the title of this thread to, Power Bulge Hood Louver, or something similar. By mentioning the louver, I think it will garner more interest.
Looks good, natural, like it could be factory... ish. This is what the decal seems to be representing/emulating.
Thanks. I was at the Fbody Beach Bash this past weekend and had an 84 T/A next to me. I should have taken a picture of them side by side. Looked great. Got many compliments on it.
Does it have an anodized finish, or is it paintable? I can't help wondering how it might look if painted to match. Probably just as good.
When you order it you can request to leave it bare. I had this one powder coated. I thought about having it painted gloss black.
Originally Posted by battmann
I like how that turned out. IMO - I’d leave it black since it matches your wheels.
I intend to. Kinda wish I had it painted a gloss black instead of powder coated the same as the IROC louvers are.
Originally Posted by LAFireboyd
Now that you've accomplished your goal, you might consider changing the title of this thread to, Power Bulge Hood Louver, or something similar. By mentioning the louver, I think it will garner more interest.
.
Was at the Fbody Beach Bash this weekend and it had plenty of interest.
Originally Posted by Mongoose
So is this a one of one or is there a potential of it being mass produced?
It will be produced when ordered. If enough interest I'm sure he'll make a batch of them.
Last edited by CharcoalBird; 10-11-2021 at 08:40 PM.
02-08-2021, 09:57 PM
