3" vs 4" cowl hood
12-27-2010, 12:49 PM
#1
Member
Thread Starter
iTrader: (2)
Join Date: Mar 2010
Location: IOWA
Posts: 166
Likes: 0
Received 0 Likes
on
0 Posts
Car: 89 IROCZ
Engine: Forged 347 LS1
Transmission: Built 4L60E with 4k stall
Axle/Gears: 4th gen w/ 3.42 gears
3" vs 4" cowl hood
Hi, as the title indicates i'm trying to decide between a 3" and a 4" cowl hood. Its going on a 89 iroc. I want something that will look nice but not block my view of the road and traffic too much while driveing. Any thought or opinions. Any pics would be helpfull as well.
Thanks
Thanks
12-27-2010, 12:54 PM
#2
Senior Member
iTrader: (8)
Join Date: Jun 2009
Location: Peoria, AZ
Posts: 768
Likes: 0
Received 2 Likes
on
2 Posts
Car: 91 Z28, 2000 T/A
Engine: SBC 355, LS1
Transmission: T56, T56
Axle/Gears: 10bolt 3.73, 3.42
Re: 3" vs 4" cowl hood
I had a 4" cowl on my 84 Z, I'm 5' 10" and it didn't block very much of my vision, I daily drove the car b/c it was the only thing I had when I was 19. It did take a little getting used to, but I never ran into anything! haha
12-27-2010, 02:28 PM
#3
Member
Thread Starter
iTrader: (2)
Join Date: Mar 2010
Location: IOWA
Posts: 166
Likes: 0
Received 0 Likes
on
0 Posts
Car: 89 IROCZ
Engine: Forged 347 LS1
Transmission: Built 4L60E with 4k stall
Axle/Gears: 4th gen w/ 3.42 gears
Re: 3" vs 4" cowl hood
Thanks... have any pics of the car?
12-27-2010, 03:16 PM
#4
Senior Member
iTrader: (8)
Join Date: Jun 2009
Location: Peoria, AZ
Posts: 768
Likes: 0
Received 2 Likes
on
2 Posts
Car: 91 Z28, 2000 T/A
Engine: SBC 355, LS1
Transmission: T56, T56
Axle/Gears: 10bolt 3.73, 3.42
Re: 3" vs 4" cowl hood
For whatever reason it wont allow me to enlarge this pic from the driver seat. But this pic is taken with my head back against the head rest for somewhat of a driver's view. It makes visibility look worse than it really is in this pic
Last edited by 3rd gen Will; 12-27-2010 at 05:18 PM.
12-27-2010, 05:15 PM
#6
Senior Member
iTrader: (8)
Join Date: Jun 2009
Location: Peoria, AZ
Posts: 768
Likes: 0
Received 2 Likes
on
2 Posts
Car: 91 Z28, 2000 T/A
Engine: SBC 355, LS1
Transmission: T56, T56
Axle/Gears: 10bolt 3.73, 3.42
Re: 3" vs 4" cowl hood
Well I had a Harwood on my 84 Z and it was perfect. Didn't require anything except trimming the front part of it which they leave long intentionally acording to Harwood.
12-27-2010, 05:35 PM
#7
Supreme Member
Join Date: Mar 2001
Location: Pekin, IL
Posts: 1,754
Likes: 0
Received 0 Likes
on
0 Posts
Car: 91 Formula, 79 Trans Am, 72 LeMans
Engine: 305 TPI, 6.6, 350 Pontiac
Transmission: T5, 3 speed, TH350
Re: 3" vs 4" cowl hood
I have a 4 inch VFN I just traded for. Fits perfect and like the previous post said, you just need to trim the front edge/lip. Not the best pics but best I can do right now...
Will have some better pics once the car is finished with paint.
Will have some better pics once the car is finished with paint.
Trending Topics
01-01-2011, 10:05 PM
#8
Supreme Member
Join Date: May 2001
Location: Your neighbor's hood, MD
Posts: 2,228
Likes: 0
Received 2 Likes
on
2 Posts
Car: 1987 Camaro Z28 IROC-Z
Engine: 5.7L TPI
Transmission: T5
Axle/Gears: 3.42:1
Re: 3" vs 4" cowl hood
2.5 or 3" IMHO is the way to go. 4" is flat out too big.
That, and most all of the 4" hoods are made with the 1st gen camaro body line/ridge going down the center. It looks, well, Ugh.
That, and most all of the 4" hoods are made with the 1st gen camaro body line/ridge going down the center. It looks, well, Ugh.
01-01-2011, 10:29 PM
#9
Senior Member
Join Date: Oct 2009
Location: New York
Posts: 525
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1988 Camaro IrocZ
Engine: Holley Stealth Ram 385 Stroker
Transmission: Redline Performance 700r4 Trans
Axle/Gears: Bulletproof 4thGen Ls1 SS Rear 3.73
Re: 3" vs 4" cowl hood
go for the sunoco cowl. its 2.5-3" clearence and looks great. You don't see them too often either.
-
-
01-02-2011, 07:59 PM
#10
Supreme Member
iTrader: (4)
Join Date: Oct 1999
Location: GO PACK GO
Posts: 4,211
Likes: 0
Received 2 Likes
on
2 Posts
Car: 83Z28 HO
Engine: Magnacharged Dart Little M 408
Transmission: G Force 5 speed
Axle/Gears: Moser 9" w/Detroit Trutrac
Re: 3" vs 4" cowl hood
01-02-2011, 08:19 PM
#11
Supreme Member
iTrader: (25)
Join Date: Feb 2006
Location: Manteca,California. Nor Cal.
Posts: 7,260
Likes: 0
Received 5 Likes
on
5 Posts
Car: SOLD IT. Mopar guy only now.
Engine: gone
Transmission: gone
Axle/Gears: gone
Re: 3" vs 4" cowl hood
my sig pic is the 2.5 inch goodmark steel hood...they say 2.5 but its more of a little over 3. I daily drive mine and i can see everything no problem. But I am also 6'1
01-02-2011, 11:08 PM
#12
Member
Join Date: May 2010
Location: Toronto, Ontario
Posts: 247
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1987 Z28 Camaro
Engine: 30Slow
Transmission: 700R4
Re: 3" vs 4" cowl hood
dear lord.. i dont like 4inch cowls
unless of course you got a big block 
then its suiting. Last edited by BrandonSB; 01-02-2011 at 11:08 PM. Reason: cause i wanted to :)
01-05-2011, 09:18 PM
#14
Junior Member
Join Date: Jul 2004
Location: titusville FL
Posts: 79
Likes: 0
Received 0 Likes
on
0 Posts
Car: 91 camaro rs
Engine: tbi 305
Transmission: 5 speed
01-05-2011, 09:57 PM
#15
Member
Join Date: Mar 2007
Location: elizabethtown ky
Posts: 138
Likes: 0
Received 2 Likes
on
2 Posts
Car: 1991 camaro RS
Engine: currently swapping 5.3
Transmission: 4l60e
Axle/Gears: soon to be 4:11
Re: 3" vs 4" cowl hood
I'm on my phone right know, so I can't upload any pics of my car, search. hugger 91. and ull find a bunch of pics, my car has a 4inch goodmark steel hood.
01-07-2011, 09:13 AM
#17
Supreme Member
Re: 3" vs 4" cowl hood
Unless you need the room or have something under the hood to back up the look stay with a 3" cowl. Nothing worse then all show no go.
Thread
Thread Starter
Forum
Replies
Last Post
91TTOPZ
Exterior Parts for Sale
5
09-20-2016 12:42 PM
